FG Füge- und Schweißtechnik
Refine
Year of publication
Document Type
Way of publication
- Open Access (7)
Keywords
- schweißen (26)
- fügen (23)
- Fügetechnik (19)
- welding (12)
- Simulation (10)
- mechanical properties (8)
- microstructure (6)
- Laserstrahlschweißen (5)
- Schweißsimulation (5)
- Al – Mg – Si alloy (4)
Institute
For the purpose of this research, single track details were manufactured in the shape of thin walls with a length of 100 mm and a height of 80 mm. Two welding speeds were chosen for this experiment–13.3 mm/s and 20.0 mm/s corresponding to the following heat inputs: 120 J/mm and 80 J/mm. The gas metal arc welding (GMAW) method was used for the build-up of the specimens in the cold arc pulse mode. The structure of the specimens was studied using X-ray diffraction (XRD) analysis carried out with CuKα radiation with a wavelength of 1.5406 Ǻ, optical microscopy, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDX). Furthermore, the Vickers hardness of the samples was determined using a ZwickRoell DuraScan 10/20 G5 unit at a force of 1 N. A preferred crystallographic orientation towards the (200) plane was observed in all cases, however a vastly textured structure was observed with inclusions of peaks in the (111), (220), and (311) crystallographic planes. The full width at half maximum (FWHM) of samples taken from different stages of build-up was calculated indicating an increase of the dislocation density at the more advanced stages of specimen growth. Despite that an increase of the hardness was observed towards the top of both specimens. This is attributed to the change in the structure of the αAl + Si formations from an irregular one at the bottom of the specimens, towards a fibrous one at the top. The results are discussed in regard to the optimization of the build-up process during wire arc additive manufacturing (WAAM).
Das pulverbasierte 3D-Metalldrucken ermöglicht die Fertigung von hochkomplexen Integralbauteilen, die als Trägerstruktur für Mikroreaktoren benutzt werden. Nach einer Beschichtung der Struktur mit einem Katalysatormaterial, können diese Mikroreaktoren höchst effizient für die CO2-Methanisierung eingesetzt werden. Durch die additive Fertigung mit dem selektiven Laserstrahlschmelzen (SLM) wurden adaptierte dreidimensionale periodische Gitterstrukturen mit sehr geringen Wandstärken hergestellt. Diese weisen ein sehr günstiges Verhältnis von Oberfläche zu Volumen (TPMS - Triply periodic minimal surface) auf. Des Weiteren zeigen die TPMS-Strukturen vorteilhafte Strömungseigenschaften, die sowohl für die Beschichtung mit dem Katalysator-Material als auch die Durchströmung mit den Reaktionsmedien im Betrieb essentiell sind. So ist es beispielsweise möglich, durch die Variation der Dimension einer TPMS-Struktur die Oberfläche pro Volumeneinheit, den hydraulischen Durchmesser des Reaktors und somit auch den Transportprozess des Fluids deutlich zu verbessern. Diese Faktoren ermöglichen eine effektivere Gas-Katalysator-Reaktion. Im Vergleich zu Mikroreaktorstrukturen aus den traditionellen Herstellungsverfahren liefern die additiv gefertigten Strukturen sowohl eine höhere CO2-Umwandlungsrate als auch eine CH4-Selektivität innerhalb des diffusionskontrollierten Bereichs.
Im vorgestellten Projekt wurden werkstoff- und konstruktionsgerechte Knotenformen aus Aluminiumschaumsandwich gestaltet und mit unterschiedlichen Schweißverfahren, wie dem Metall-Inertgas-Schweißen und dem Rührreibschweißen, gefügt und geprüft. In umfangreichen Untersuchungen wurden die Knoten, der Sandwichverbund und die Einzelkomponenten des Sandwich, Schaum und Decklagen, anhand der statischen Festigkeit und Schwingfestigkeit bewertet. Zusätzlich wurden innere Schädigungsmechanismen betrachtet. Mit experimentellen und numerischen Nachweismethoden konnte die anwendungssichere Knotengestaltung, -anbindung und -berechnung der unterschiedlichen Verbindungstypen umgesetzt werden. Die Ergebnisse wurden im Rahmen der Nachweisführung gegenübergestellt und hinsichtlich eines praxisgerechten Einsatzes nach FKM-Richtlinie bzw. Eurocode9 bewertet. Mit den ermittelten Ergebnissen wurde die bisherige Gestaltungs- und Fügerichtlinie um neue Verbindungstypen erweitert.
Microhardness variations across the friction stir welded (FSW) and impulse friction stir welded (IFSW) AA2024–T351 joints have been elucidated by the transformations of the S–Al2CuMg phase with a special focus on a distinguished hardness peak within the heat-affected zone (HAZ) of the impulse welds. The increase in hardness within the stir zone (SZ) originated from the partial re-precipitation of the initial Guinier-Preston-Bagaryatsky zones (GPB) and metastable S needles, previously dissolved.) Formation and growth of stable S precipitates via coalescence accounted for the softening through the thermo-mechanically affected zone (TMAZ). The peak strengthening within the HAZ of the IFSW joints was mainly caused by the dense needle-shaped S particles, which can be explained by a mutual influence of the process specific temperature and strain cycles. Dislocations and subgrain boundaries introduced to the material due to plastic deformation facilitated the nucleation of strengthening S precipitates in the HAZ. It demonstrates that the impact of deformation should be considered by the characterization of the precipitation development in the HAZ.
The effect of heat treatment at various temperatures (650, 850, 1050, and 1100°C) and dwell times (10 min and 1 h) on the metallurgical and microstructural evolution as well as on the related tensile properties of stainless steel 316L processed by selective laser melting (SLM) has been systematically evaluated. The metallurgical and microstructural features such as defects, stability of the columnar–cellular structure and substructure, second phase particles, and phase transformation imparted by SLM and heat treatment have been discussed. It has been shown that the processing conditions specific to SLM significantly alter the kinetics of phase evolution compared to standard welding techniques which affects the accuracy of the prediction. The influence of these characteristics on tensile properties and hardness was elucidated. It was disclosed that with increasing heat treatment temperature there was a gradual increase in elongation but a decrease in strength related to the dislocation density and the development of the microstructure.
Durch den strukturellen Einsatz von Faser-Kunststoff-Verbunden (FKV) lassen sich hochwertige gewichtsoptimierte Karosserien in Mischbauweise umsetzen. Die untersuchte CMT-Pin-Schweißtechnik zur Verbindung von thermoplastischen Organoblechen mit Stählen bietet, im Vergleich zu anderen Verfahren, neben einer einseitigen Zugänglichkeit, ein hohes Leichtbaupotenzial. Das Vorhaben wurde auf eine werkstoff-, prozess- und konstruktionsgerechte Umsetzung des Verfahrens ausgerichtet.
Auf Basis experimenteller und numerischer Untersuchungen wurde eine Methode zum Vorwärmen von Organoblechen mittels Infrarotstrahlung entwickelt. Die Eignung der CMT-Pin-Technologie wurde sowohl für das Fügen von karbon- als auch glasfaserverstärktem PA6 betrachtet. Als Bewertungskriterien wurden das Schweißgut sowie der Faser- und Matrixerhalt in Abhängigkeit der Schweißparameter untersucht. Das entwickelte Verfahren wurde mit herkömmlichen Fügemethoden bzgl. der in Kopf- und Scherzugversuchen ermittelten Festigkeiten verglichen. Zur Bestimmung der Beständigkeit der Verbindungen gegen unterschiedliche Witterungsbedingungen wurden Salzsprühnebel- und Wechselkorrosionstests durchgeführt. Mit dem Fügen von Hutprofilen wurde die Anwendung der entwickelte CMT-Pin-Technik am Tunnel sowie den Längs- und Querträgern der Bodenstruktur eines Kraftfahrzeugs demonstriert.
The beam inclination leads to a change in the laser spot size on the material surface. The higher the inclination, the larger the irradiated area and the lower the laser intensity. Moreover, if the material surface is outside of the beam focal plane, the intensity distribution profile becomes asymmetric. In this study, a heat source model, which calculates the intensity distribution on the workpiece surface as a function of beam parameters (beam waist, divergence half-angle) and process parameters (laser power, incidence angle, and distance to focal plane) was developed. The applicability of the heat source model was demonstrated by simulating 4 different laser hardening regimes. Once the heat efficiency coefficient had been calibrated the developed finite-element model allowed computation of temperatures while hardening with perpendicular laser beams as well as with inclined beams. The open-source software FEniCSx was used for the finite element computations. The mathematical formulation, required for performing temperature simulations with FEniCSx was briefly introduced.
Due to the recent developments of hardware components and the hereby resulting ability to increase process parameters, the application area of the cold gas spray technology is expanding quickly. The present
research focuses on the influence of working gas pressure and working gas temperature on the adhesive strength of inner diameter coatings, which were produced with two different alloy steel powder variants. Gas pressure and gas temperature were varied in four different parameter sets. At first, the powder variants were examined for morphology and particle size distribution. Secondly, the influence of
four different process parameters on the achievable particle velocity was measured. In addition, the arithmetical mean height (Sa) of the coating was measured in order to determine the effect of the four parameter sets on the achievable surface roughness. Furthermore, the impact of the process parameters on the steel particles’ penetration
depth into the aluminum substrate was examined. Finally, adhesion strength measurements of the inner diameter coatings were carried out. The results reveal that with rising process parameters, the particle velocity increases, and the achievable surface roughness is lowered. It was also shown that the penetration depth of the particles into
the substrate increases with increasing particle velocity. In addition, this study demonstrated a dependence of the process parameters on the adhesion strength for inner diameter coatings.
3D-printed structured catalysts for CO2 methanation reaction: Advancing of gyroid-based geometries
(2022)
This work investigates the CO2 methanation rate of structured catalysts by tuning the geometry of 3D-printed metal Fluid Guiding Elements (FGEs) structures based on periodically variable pseudo-gyroid geometries. The enhanced performance showed by the structured catalytic systems is mostly associated with the capability of the
FGEs substrate geometries for efficient heat usages. Thus, variations on the channels diameter resulted in ca. 25% greater CO2 conversions values at intermediate temperature ranges. The highest void fraction evidenced in the best performing catalyst (3D-1) favored the radial heat transfer and resulted in significantly enhanced catalytic activity, achieving close to equilibrium (75%) conversions at 400 ◦C and 120 mL/min. For the 3D-1 catalyst, a mathematical model based on an experimental design was developed thus enabling the estimation of its behavior as a function of temperature, spatial velocity, hydrogen to carbon dioxide (H2/CO2) ratio, and inlet CO2 concentration.
Its optimal operating conditions were established under 3 different scenarios: 1) no restrictions, 2) minimum H2:CO2 ratios, and 3) minimum temperatures and H2/CO2 ratio. For instance, for the lattest scenario, the best CO2 methanation conditions require operating at 431 ◦C, 200 mL/min, H2/CO2 = 3 M ratio, and inlet CO2 concentration = 10 %.
Among different joining methods, the electron beam welding is recently applied for manufacturing of turbine components from temperature-resistant nickel-based conventionally cast Alloy 247 LC CC. However, the high tendency to hot cracking, in particular the formation of solidification cracks, remains a major challenge. Experiments indicate a significant reduction in hot cracks if the welding is performed outside the common welding parameter range. To understand these observations, a study of local thermo-mechanical conditions during electron beam welding of Alloy 247 samples was carried out using numerical simulations. The results were subsequently compared with reference test welds. For this purpose, a finite element model for coupled transient thermal and mechanical analysis was created and used. The work presents a comparative analysis of the evolution of strain components in brittle temperature range during cooling, considering the distribution and orientation of the cracks. Various relations between local strain kinetics and crack appearance, with notable influence of the plastic strain vector, were observed. Finally, the aspects of assessment of hot crack susceptibility with aid of thermo-mechanical welding simulation are discussed.