Fakultät Maschinenbau
Refine
Year of publication
Document Type
- conference proceeding (article) (30) (remove)
Has Fulltext
- no (30)
Is part of the Bibliography
- no (30)
Institute
- Fakultät Maschinenbau (30) (remove)
Structural mechanic properties of fiber reinforced plastics depend on the single components’ properties, namely matrix and fiber [5]. Simple micromechanic homogenization theories reach a limit when a laminate consists of fabric reinforced layers instead of unidirectional layers. The ondulations of warp and fill yarn caused by the textile semi-finished product are the reason why the mesoscopic scale, which is in between the microscopic and the macroscopic scale, has to be taken into account when mechanically characterizing fabric reinforced composites [3]. In this scale a mesomechanic kinematic can be derived analytically. Especially, when considering free damped vibrations of structures the repeated acting of the kinematic correlation significantly affects the damping behaviour to higher values compared to theoretically predicted damping ratios. The model is investigated using Finite-Element-Analyses and basically validated experimentally.
High quality semi-finished products with reproducible properties of basaltic fibres are hardly available on the market. In order to examine the properties of basalt fibre reinforced plastics high quality specimens are necessary. The fibre volume content and the porosity of the produced specimen are used as the typical criteria to evaluate the achieved quality of the produced material. The effect of the geometrical properties of the different semi-finished products on the fibre volume contents is relatively small whereas the porosity content is considerably affected.
This paper describes the results of tensile tests and finite element (FE) calculations with representative volume elements (RVEs) of basalt fibre reinforced plastic with two different types of fabric reinforcements. As fabric reinforcements show repeating ondulations of warp and fill yarn, simple mixtures laws reach their limits. That is the reason why the mesoscopic dimension, lying between the microscopic and the macroscopic dimension, has to be taken into account when a mechanical characterization of fabric reinforced composites is carried out. The aim of this work is to determine the stiffness of a fabric reinforced composite in warp and fill direction with numerical investigations. The simulations are based on FE-calculation with two different RVEs. The tensile tests and the FE-calculations have been carried out for two different types of basalt fabrics, namely twill 2/2 and twill 1/3. The comparison between the experimental data and the results of the FE-calculations are provided in order to support the validity of the proposed model.
Purpose:
A route to manufacture porous carbon fiber reinforced plastic (CFRP) for study purposes is described.
Design/methodology/approach:
The porous CFRP is characterized using standard techniques such as matrix digestion as well as the more sophisticated method of high resolution Microfocus X-Ray Tomography (μCT). A comparison of the results of those methods is presented. The mass gains of specimens with a wide range of porosity have been measured both in constant humidity and in alternating environments.
Findings:
It could be shown that severe temperature changes can temporarily increase the moisture content of porous CFRP. However, after the return to a constant environment, the moisture content returns back to saturation levels. Furthermore, it could be shown by X-Ray Tomography that even under severe climatic conditions no permanent liquid water condensates inside the pores.
Research limitations/implications:
Using Microfocus Computed Tomography it could be shown that even after nearly a year under hot-wet conditions and more than 150 severe temperature cycles there is no liquid water detectable inside the pores.
Originality/value:
In this paper the effects of severe temperature changes and high humidity on porous CFRP.
Investigation of Bolted Composite Joints with Different Reinforcement Elements at the Bolt Hole
(2014)
Structural Dynamic Analysis of Thin Composite Plates Using Noncontact Measurement and Excitation
(2016)
Analysis of the Acoustic Emission Failure Frequencies of Glass Fiber Reinforced Composite Components
(2017)
This article presents first results of artificial aging experi-ments by ultraviolet (UV) irradiation on thermoplasticmaterials conducted as an intent of the research project Thermoplastic Composite Structures (TheCoS) in colla-boration of the Ostbayerische Technische Hochschule(OTH) Regensburg and the University of West Bohemia(UWB) in Pilsen as part of a cross-border cooperation. In technical applications, thermoplastic materials are oftenaffected by aging and a related deterioration of the mechanical properties. Therefore, it is necessary to identifythe aging behavior of thermoplastic materials. For this,experiments were performed for three thermoplasticmaterials, namely polypropylene (PP), ultra high mole -cular weight polyethylene (UHMWPE) and high impactstrength polystyrene (HIPS). For these experiments, a UV chamber was constructed according to the internationalstandard EN ISO 4892-3 for simulation of exposurebehind window glass. The results are evaluated by testing the flexural strength and the dynamic mechanicalresponse after a selected period of time under UV lightand then compared to untreated test specimens.
The effect of process variables such as shear rate and temperature on the viscosity of polypropylene during the processing of thermoplastic based composites was investigated in this study. The melt impregnation is used in the process of continuous glass fibre reinforced thermoplastic composites. To develop a mathematical model for roving impregnation, it's essential to know about the viscous behaviour of the matrix system. Therefore, this paper will discuss rheological models to describe these phenomena, based on the gathered viscosity data from the partner laboratory at the University of West Bohemia in Pilsen.
We present the application of plasma actuators as a technology for ice prevention at airfoils. The miniaturized dielectric barrier discharge (DBD) plasma actuators (PA) were fabricated by means of microelectromechanical systems (MEMS). We elucidate how to make the actuator samples scalable and applicable to any desired shape by the use of flexible inorganic zirconia substrates. For this purpose, we applied our developed embedding method to integrate the micro actuators in modern carbon/glass fiber reinforced polymer (CFRP/GFRP) materials. Next, the embedded actuator samples were mounted on a mechanical air profile-like fixture and placed in the icing wind tunnel iCORE. The samples were tested in rime ice conditions at temperatures of -15 to -20° C and air speeds up to 30 m/s. Unlike other groups we used a thin film zirconia substrate as dielectric for the plasma actuator. Due to the low substrate thickness of just 150 µm, an operating voltage of 2 kVRMS is already sufficient enough for a stable plasma formation. The experiments show that the operated actuator was able to prevent the ice formation and first indications of a De-icing function were also found. Hence, we show that it is feasible to realize an anti-icing system with zirconia-based plasma actuators operated at lower voltages compared to conventional ones.