Refine
Year of publication
Document Type
- conference proceeding (article) (76)
- Article (45)
- Part of Periodical (8)
- conference talk (4)
- Part of a Book (1)
- conference proceeding (volume) (1)
Is part of the Bibliography
- no (135)
Keywords
- field emission (24)
- Current measurement (13)
- silicon (13)
- Iron (10)
- CATHODES (8)
- elemental semiconductors (8)
- field emitter arrays (8)
- Etching (7)
- field emitter array (7)
- silicon tips (7)
Institute
- Fakultät Angewandte Natur- und Kulturwissenschaften (127)
- Labor Mikrosensorik (121)
- Hochschulleitung/Hochschulverwaltung (8)
- Institut für Angewandte Forschung und Wirtschaftskooperationen (IAFW) (7)
- Fakultät Elektro- und Informationstechnik (2)
- Fakultät Maschinenbau (2)
- Labor Faserverbundtechnik (LFT) (2)
- Labor Optische Übertragungssysteme (2)
- Technologie-Campus Neustadt an der Donau (2)
- Labor Biofluidmechanik (1)
Begutachtungsstatus
- peer-reviewed (94)
The study on electrical properties for both 2,3,7,8,12,13,17,18-octaethyl-21,23H-porphine Cu (II) (Cu-porphyrin) and 2,3,7,8,12,13,17,18-octaethyl-21,23H-porphine (porphyrin) thin film, which were fabricated using spin coating method was conducted. Porphyrins were diluted with chloroform of various concentrations (0.05 mg/ml, 0.1 mg/ml, 0.5 mg/ml, 2.0 mg/ml and 3.0 mg/ml). The solution was spin coated on top of glass substrates. A layer of aluminum was evaporated on top of the organic thin film through thermal evaporation and shadow mask was placed on top of the organic thin film where two electrodes with a gap of 50 μm were formed. Surface morphology of the organic thin film was observed by scanning electron microscope (SEM) and profilometer. Different concentrations of organic solutions greatly affected the molecular packing and arrangement order of the organic thin film and thickness of the organic layer and eventually affected electrical properties of the devices.
The performance of thermal conductivity vacuum gauges can be improved by a well-designed geometry. The lower measurement range limit is determined by the size of the active sensing area and the thermal conduction heat losses through the supporting structures. The upper measurement range is limited by the distance between the heated element and the cold reference plane. Silicon based MEMS-technology gives the possibility to fabricate both sensing structures with suitable areas out of low thermal conductive materials and narrow gaps in order to extend the measurement range in both directions. In this work we present a MEMS-process to fabricate high thermal resistance sensor structures. The rectangular sensitive areas are anchored by four beams and are structured out of low thermal conductive PECVD-siliconnitride films with 1 µm in thickness. The metallic heating structure is completely embedded in the SiN-layer. Both sensitive area and its support beams were released from the silicon bulk material by anisotropic underetching. In this way a free-supporting structure with a gap of 150 μm to the silicon substrate was formed. The influence of the filament geometry and temperature was systematically investigated to determine the properties of the chips as thermal conductivity vacuum gauges. The temperature of the sensitive area was held constant by a self-balancing bridge circuit and the heating power was measured by a Δ-Σ-ADC. The average solid state thermal conductivity is in the order of 106WK1. The measuring range of the most sensitive structures covers 8 orders of magnitude from 105 mbar to 1000mbar.
The authors report on the fabrication and characterization of p-type Si tip arrays with an integrated gate electrode for applications as field emission electron sources. After the reactive ion etching of the emitters, the combined thermal dry and wet oxidation was used for both the sharpening of the emitters and for the realization of an enhanced insulation layer. Au was evaporated in a self-aligned process as gate electrode. Arrays of 16 Si tips were fabricated with tip heights of about 3 μm and tip radii of about 20 nm with integrated gate electrode concentrically positioned ≈2 μm below the tip apex. Integral measurements with an additional anode showed improved field emission properties with a reproducible and stable emission behavior. A fast activation of the tips, low onset voltages of about 30 V, and moderate field emission currents up to 0.55 μA were noticed. The field emission parameters were calculated using the Fowler–Nordheim characteristics. A pronounced saturation regime was observed, and current fluctuations of less than ±1% were investigated for 30 min. Long-term measurements were carried out for a period of more than 8 h. In the first 6 h of operation, the authors observed a drift of the emission current from 0.35 to 0.55 μA caused by an increased emission surface.
Innovatives Verfahren zur Herstellung und Integration metallischer Nanokonen für die Feldemission
(2017)
In den letzten Jahren wurde am Institut für Elektromechanische Konstruktionen die Fabrikation und Integration von metallischen Nanodrähten und Nanokonen mittels Template-basierter Abscheidung erforscht. Diese Variante der in-situ Abscheidung von metallischen Nanostrukturen bietet eine Vielzahl von Anwendungsmöglichkeiten. Im Rahmen dieses Beitrags werden das Herstellungsverfahren zur Herstellung metallischer Nanokonen vorgestellt. Dies beinhaltet sowohl die Templatepräparation mittels asymmetrischen Ätzens als auch die anschließende Integration mittels galvanischer Abscheidung. Eine Anwendung der metallischen Nanokonen stellt die Verwendung als Feldemitter in der Vakuumelektronik dar. Es werden erste Messungen der Langzeitstabilität des Feldemissionsstromes der metallischen Konen präsentiert.
Fabrication and simulation of silicon structures with high aspect ratio for field emission devices
(2014)
To obtain higher field enhancement factors of Si-tip structures, we present an improved fabrication process utilizing reactive-ion etching (RIE) with an inductively coupled plasma (ICP). In our design, a pillar under the tips is realized by a combination of RIE with ICP. With adjusted power settings (≈ 240 W) and step times (<; 5 s), vertical slopes with a low roughness of approximately 10 nm to 20 nm are possible. The remaining silicon is oxidized thermally to sharpen the emitters. A final tip radius of R <; 20 nm is obtained for the tips of the emitters. The pillar height HP can be mainly adjusted by the duration of the ICP-etching step. A total emitter height of H ≈ 6 μm with a pillar height of HP ≈ 5 μm is achieved. Simulations with COMSOL Multiphysics® are applied to calculate the field enhancement factor β. A two-dimensional model is used in rotational symmetry. In addition to the previous model, a pillar with a varying diameter ØP and height HP is added. A conventional emitter (H = 1 μm and R = 20 nm) placed on a pillar of the height HP ≈ 5 μm approximately results in a three times higher β-factor (β≈ 105). By decreasing the diameter ØP a slight increase of the β-factor is observed. However, the aspect ratio of the emitter mainly influences on the β-factor.
A compact vacuum-sealed field emission electron gun with an operation voltage below 5 kV is presented. With a 150 nm thick pyrolytic carbon membrane, a transmission of 40% at 5 kV is obtained. For more than 2500 h of continuous operation at an emission current of 100 nA, no significant increase (<50V ) and almost no degradation were found. From this measurement, a lifetime of more than 10 000 h at continuous operation with approximately a linear increase of the extraction voltage from about 545 V to about 730 V is predicted. This electron source enables application of field emitter arrays in poor vacuum or even ambient pressure.
ACKNOWLEDGMENT
This work was supported by the German Federal Ministry for Economic Affairs and Energy under Project No. ZF4081502GM8. C.P., R.L., M.H., and R.S. were supported by Grant No. ZF4562901GM8.
Influence of adsorbates on the performance of a field emitter array in a high voltage triode setup
(2017)
In the present work, black-silicon field emitter arrays (FEAs) are investigated regarding the influence of residual gas pressure on the characteristics and lifetime in the high voltage triode setup. Current-voltage-characteristics at different pressure levels are recorded and show a decreasing emission current with rising pressure. This decrease can be explained by an increase of the work function and charging of the emitter surface caused by adsorbates. The emission current can be restored to its initial value by heating of the FEA up to 110 °C during active emission. With this regeneration procedure, an extended lifetime from about 20 h to 440 h at a residual gas pressure of 10−5 mbar is achieved.
An electron source with an array of individually controllable single tips allows the observation of each emitter current simultaneously as well as the measurement of the integral current. Furthermore, the initial activation process of the individual tips and current distribution of the source can be examined. The Si cathode consists of an array of 2 x 2 conically shaped emitter structures on a borosilicate glass substrate. The emitters were fabricated by laser micromachining and wet etching. Integral field emission (FE) measurements were performed in a diode configuration in a vacuum chamber at pressures of about 10(-9) mbar with a self-aligned Si extraction grid, due to adjustment pins. The total emission current was regulated to a predefined value (4.0, 10, 20, 40, and 50 mu A) by an external regulating circuit and recorded individually during the measurement. The onset voltage for a current of 1 nA varied between 320 and 430 V. The voltage conversion factor is in the range of 7.6 x 10(4) cm(-1) to 1.3 x 10(5) cm(-1). Constant currentmeasurementsover a longer periodof time (1800 values with a sample rate of 0.5 Hz) were performed and show a total current fluctuation less than 0.6% due to the regulation circuit. Despite the stable total current in regulated operation, it was observed that the individual emitters fluctuate up to 75% for low (similar to 10(-8) A) and 5% for high (similar to 10(-5) A) currents.
The field electron emission characteristics of individual tips of a silicon field emitter array are analyzed. The array of conical‐shaped tips is fabricated on a p‐type silicon wafer by using reactive ion etching and sharpening oxidation. The tips are decorated with single tungsten nanoparticles at their apexes. Furthermore, the focused ion beam is also used to increase surface conductivity of some of the tips. Comparative measurements of field emission are performed by using the scanning anode probe field emission microscopy technique. All types of tips demonstrated emission activation consisting of a sudden current increase at a certain value of the applied voltage. Compared to the pristine tips, a noticeable reduction of the saturation effect in the current–voltage characteristics and a smaller light sensitivity for the decorated tips is found. For ion‐treated tips, saturation effects and light sensitivity are completely suppressed. Scanning electron microscopy observations reveal the formation of single nanoscale protrusions extending from the metal particles and from the apexes of bare ion‐treated tips after exposure under strong electric fields during the field emission measurements. The influence of protrusions growth on characteristics of silicon field emitter arrays is discussed.
The components for a silicon chip electron source were fabricated by laser micromachining using pulsed laser ablation and wet chemical cleaning and etching dips. The field emission electron source consists of a silicon field emission cathode with 4 × 4 conical shaped emitters with a height of 250 μm and a tip radius of about 50 nm, a 50 μm thick laser-structured mica spacer, and a silicon grid electrode with a grid periodicity of 200 μm and a bar width of 50 μm. These three components are combined to a single chip with the size of 14 × 10 mm2 and the thickness of 1 mm to form the electron source. Several of these devices were characterized in ultrahigh vacuum. Onset voltages of about 165 V and cathode currents of about 15 μA for voltages lower than 350 V were observed. Operating the electron source with an anode voltage of 500 V and an extraction grid voltage of 300 V yielded a cathode current of 4.5 μA ± 8.9%, an anode current of 4.0 μA ± 9.6%, and a corresponding grid transmittance of 89%. Regulating the anode current by the extraction grid voltage, an extremely stable anode current of 5.0 μA ± 0.017% was observed. A long-term measurement over 120 h was performed, and no significant degradation or failure was observed.