7.2 Ingenieurbau
Filtern
Erscheinungsjahr
- 2022 (52) (entfernen)
Dokumenttyp
- Vortrag (27)
- Beitrag zu einem Tagungsband (14)
- Zeitschriftenartikel (11)
Schlagworte
- Ground vibration (7)
- Structural Health Monitoring (7)
- Gründungsstrukturen (4)
- Structural health monitoring (4)
- Belastungsversuch (3)
- Building vibration (3)
- Großer Fallturm Horstwalde (3)
- Leichtbau (3)
- Modalanalyse (3)
- Offshore Windenergieanlagen (3)
- Offshore wind energy (3)
- Schwingungsdynamik (3)
- Artificial intelligence (2)
- Automatisierte schweißtechnische Fertigung (2)
- Bayesian System Identification (2)
- Brücke (2)
- Compressive strength (2)
- Digitalisierung (2)
- Earth block masonry (2)
- Elastische Elemente (2)
- Erschütterungen (2)
- Evaluation (2)
- Faseroptik (2)
- Finite Elemente Simulation (2)
- Irregularities (2)
- Layered soil (2)
- Measurement (2)
- Moisture content (2)
- Monitoring (2)
- Offshore Wind Energy (2)
- Optimal Sensor Placement (2)
- Radar (2)
- Railways (2)
- Research data management (2)
- Strukturmonitoring (2)
- Tomographic damage evaluation (2)
- Value of Information (2)
- Vehicle-track interaction (2)
- Vibration (2)
- Wellenausbreitung in der Tiefe (2)
- Acoustic emission (1)
- Ambient excitation (1)
- Asymptotic local approach (1)
- Attenuation (1)
- Automatisierte Fertigung (1)
- Automatisierte schweißtechniche Fertigung (1)
- Axle loads (1)
- Axle pulses (1)
- Bahngleis (1)
- Bauwerksdiagnostik (1)
- Bauwerksmonitoring (1)
- Bauwerksüberwachung (1)
- Belastungsfahrt (1)
- Belastungstest (1)
- Bionik (1)
- Bodenschlitz (1)
- Brücken (1)
- Buckling (1)
- Building information modelling (1)
- Combined finite-element boundary-element method (1)
- Compression tests (1)
- Concrete (1)
- Continuously inhomogeneous geological media (1)
- Coupler systems (1)
- Damage detection (1)
- Damage evolution (1)
- Datenmanagement (1)
- Dynamic axle loads (1)
- Dynamische Bodensteifigkeit (1)
- Einflusslinien (1)
- Einfügungsdämmung (1)
- Entscheidungsfindung (1)
- Ermüdungsprüfung (1)
- Erschütterungen im Fernfeld (1)
- Erschütterungsminderung (1)
- Fatigue (1)
- Filter effects (1)
- Finite element method (1)
- Finite elements (1)
- Foundation reliability analysis (1)
- Foundations (1)
- GNSS (1)
- Gebäudelagerung (1)
- Geometric vehicle and track irregularities (1)
- Global ambient vibrations (1)
- Hammer impact (1)
- High-speed (1)
- Impact (1)
- Impact damage of reinforced concrete (1)
- Impact damage on reinforced concrete (1)
- Impedanzmethode (1)
- Kraft auf den Boden (1)
- LBM-DEM (1)
- Leichtbauprinzipien (1)
- Load tests (1)
- Load-bearing behaviour (1)
- Maschinenbetrieb (1)
- Micromechanical simulation (1)
- Minderungsmaßnahmen (1)
- Modal analysis (1)
- Model update (1)
- Modell-Update (1)
- Modellierung (1)
- Modes (1)
- Modes and waves (1)
- Monopile installation risks (1)
- Monopiles (1)
- Multi-beam track model (1)
- Nachgiebigkeiten (1)
- Nelson’s method (1)
- Numerical damage simulation (1)
- Numerical simulation of impact damage (1)
- Offshore (1)
- Offshore Windenergie (1)
- Offshore geotechnics (1)
- Perfectly Matched Layer (PML) (1)
- Pfahlnachgiebigkeiten (1)
- Pile retrofit system (1)
- Prediction (1)
- Probabilistic modelling (1)
- Probability of detection (1)
- Propagation from a tunnel (1)
- Rail roughness (1)
- Railway trafiic (1)
- Random dynamics and vibrations (1)
- Randomly heterogeneous soil (1)
- Reinforcement (1)
- Relative humidity (1)
- Risslumineszenz (1)
- Rissprozes (1)
- Rissprozess (1)
- Scattering (1)
- Schadensüberwachung (1)
- Schienenfahrweg (1)
- Schienenfahrwege (1)
- Schwingungsmonitoring (1)
- Sensitivity vectors (1)
- Simple and fast prediction (1)
- Simple prediction (1)
- Soil-building interaction (1)
- Soil-wall-floor model (1)
- Sorption isotherm (1)
- Spatially varying ground conditions (1)
- Static axle loads (1)
- Statistical tests (1)
- Stiffness variation (1)
- Stress stiffening (1)
- Stress-strain relation (1)
- Structural integrity maintenance (1)
- Structural system identification (1)
- Support structures (1)
- Surface line (1)
- Systemidentifikation (1)
- Track damage quantification (1)
- Track filtering (1)
- Train passage (1)
- Train-induced ground vibration (1)
- Tunnel (1)
- Tunnel line (1)
- Tunnel-pile transfer (1)
- UAS (1)
- Ultrasonic testing (1)
- Unbounded domain (1)
- Uncertainty quantification (1)
- Varying soil stiffness (1)
- Varying stiffness (1)
- Varying track stiffness (1)
- Vibration measurement (1)
- Waves (1)
- Wheelset (1)
- Windenergieanlagen (1)
- Windenergy (1)
- building information modelling (1)
- layered soil (1)
- structural health monitoring (1)
- structural integrity management (1)
- support structures (1)
- Überwachung (1)
Organisationseinheit der BAM
- 7.2 Ingenieurbau (52) (entfernen)
Paper des Monats
- ja (1)
Eingeladener Vortrag
- nein (27)
The Perfectly Matched Layer (PML) method is an efficient approach to imposing radiation conditions at the bounded region of interest in case of wave propagation in unbounded domains. This paper presents and validates 3D FE/PML numerical schemes based on two different PML formulations for homogeneous and inhomogeneous geological media exhibiting discrete or continuous inhomogeneity. In the equation of motion for the PML domain the applied stretching behavior is expressed either as complex material properties or as complex coordinates. Both PML formulations are implemented in the FEM and verified against analytical solutions. Three different types of material inhomogeneity are considered: layered half-space, continuously inhomogeneous half-space with linear velocity profile and continuously inhomogeneous half-space with nonlinear velocity profile. Sensitivity analyses are conducted, and the performance of the developed numerical schemes is investigated taking into account a broad variation of the PML parameters. Recommendations are given for the optimal values of the PML parameters for the case of homogeneous and inhomogeneous geological media.
The attenuation of wave amplitudes is ruled by the planar, cylindrical or spher-ical geometry of the wave front (the geometric or power-law attenuation) but also by the damping of the soil (an exponential attenuation). Several low- and high-frequency filter effects are derived for the layering and the damping of the soil, for the moving static and the distributed train loads and for a homoge-neous or randomly heterogeneous soil. Measurements of hammer- and train-induced vibrations at five sites have been analysed for these attenuation and filter effects. The measured attenuation with distance can be discribed by gen-eralised power laws and some reasons will be discussed. The theoretical filter effects can well be found in the measurements.
Aim of this study is to provide information about moisture dependent material behaviour of unstabilised loadbearing earth blocks and mortars. Compressive strength and Young’s modulus were investigated after conditioning in varying relative humidity reaching from 40 % up to 95 %. The material composition and physical properties were investigated to understand the influence of relative humidity onto the mechanical properties. A normalisation of strength and stiffness by the values obtained at 23 ◦C and 50 % relative humidity reveals a linear dependence of compressive strength and Young’s modulus that is regardless of the material composition.
Thus, it is possible to describe the influence of relative humidity onto the load-bearing behaviour of unstabilised earth masonry materials in a generally valid formulation.
Train-induced ground vibrations are all generated by the vehicle, by static or dynamic vehicle loads. The most important and most accepted excitation are the dynamic wheel loads from the passage over track irregularities. Dynamic wheel loads will be compared from parallel axle-box and ground vibration measurements at more than seven sites. Some low-frequency excitation of ground vibrations, typically between 10 and 30 Hz, cannot be found in the axle-box measurements. Therefore, other vehicle modes, such as rigid bogie modes, flexible carriage modes, rigid and flexible wheelset modes, have been analysed for additional excitation forces. These vehicle dynamics analyses give an explanation for higher axle-box results at high frequencies, but not for the excitation of the higher low-frequency ground-vibration component. Finally, the effect of the moving static train loads will be analysed. For a regular track and soil, the moving static train loads yield the quasi-static response which exists only in the low-frequency nearfield of the track. If the support stiffness is randomly varying along the track, the pulses on the track generate an additional low-frequency component which is called the irregular pulse responses.
This component will be demonstrated by numerical analysis where all axle pulses are superposed in frequency domain.
The train passages over intact or damaged slab tracks on different soils have been calculated by two methods. The finite element method (FEM) uses a Winkler soil under the track model by adding a thin “soil layer”. The combined finite element boundary element method has a continuous soil model which is included by the boundary element method. The basic results are the distributions of the track (rail, track plate, and base layer) displacements along the track for a single axle laod. These solutions are superposed to a complete train load and transformed to time histories. The influence of track and soil parameters has been analysed. The main interest is the influence of the track damage. A gap between track plate and base layer of different lengths has been studied for changes in amplitudes and widths of deflection. A best fit to measured track displacements has been found so that the track damage can be identified and quantified. The FEM model with Winkler soil cannot be fitted to the amplitude and width with the same soil parameters. Therefore, the FEBEM model is preferable for these railway track problems.
block and mortar types is analysed with particular regard to the influence of varying relative humidity. The uniaxial compressive strength and deformation characteristics of unstabilised earth blocks and mortars as well as of unstabilised earth block masonry are studied in detail and compared to conventional masonry to evaluate whether the structural design can be made accordingly. An increase of 30 % points in relative humidity leads to a reduction of the masonry´s compressive strength between 33 % and 35 % whereas the Young´s modulus is reduced by 24–29 %. However, the ratio between the Young´s modulus and the characteristic compressive strength of earth block masonry ranges between E33/fk = 283–583 but is largely independent of the relative humidity. The results show that the mechanical properties of the investigated unstabilised earth block masonry are sufficient for load-bearing structures, yielding a masonry compressive strength between 2.3 MPa and 3.7 MPa throughout the range of moisture contents
investigated. In general, the design concept of conventional masonry can be adapted for unstabilised earth masonry provided that the rather low Young´s modulus as well as the moisture dependence of both, compressive strength and Young´s modulus, are sufficiently taken into
account.
Vibration measurements have many causes and many technical and natural sources. Problems can sometimes be solved by short-term measurements, but in many cases, a long-term measurement is necessary. In long-term measurements of days, weeks, months and even years, it is easy to collect a huge quantity of raw data, but at the end, the post-processing of these data can be exhausting (for example one-year vibration data of a wind energy tower). A software has been developed which con-sists of measuring and evaluation routines where the measuring routines can operate different meas-uring systems and different measuring cards. The main advantage of this software is the fact that the interesting evaluations can be integrated in the measuring process so that the characteristics of the vibration can be extracted without storing all the raw data. Only important time segments are stored, for example train passages. The overall concept of the software and the main evaluation routines will be described in some details. Examples of our measurement experience will illustrate the capabilities of the software. 1) Surveying construction work in nearby sensitive buildings (for example an old wind tunnel), including a stable alarm system and meaningful vibration limits. 2) Prediction of train-induced vibration for a planned building to prevent annoyance and to improve the building design. 3) Modal analysis and long term measurements of several single- or multi-span, concrete or steel bridges 4) Modal and wave analysis of coupled floors in a historical building (“Neues Palais” at Potsdam). 5) Soil properties of various measurement sites (different routines to evaluate the dispersion). Moreover, from many projects, amplitudes, frequencies, and attenuation laws have been collected and analysed for the different sources such as vibratory or impact pile driving and ground compaction, demolition work with different machines, blasting in quarries and in tunnel works, bomb and mine clearing.
Usually, geometric irregularities are considered as the main cause of ground vibrations from trains. A varying stiffness of the track, the track support and the soil can also generate ground vibrations. The regular stiffness variation of the track on and between the sleepers results in a deterministic dynamic axle load. The random stiffness variation of the track support yields also dynamic axle loads. The dynamic axle loads are generated by the varying wheel displacements under the static axle load by the acceleration of the unsprung mass of the rail vehicle. The random stiffness variation has a second effect. The pulses from the passage of the static axle loads are superposed regularly to the quasi-static response, but also irregularly to yield a “scattered” part of the axle pulses. The same holds for a random variation of the soil stiffness. All these effects of stiffness variations have been calculated by wavenumber-domain multi-beam track models, a random finite-element soil model and the superposition of axle impulses in a stochastic simulation. The results are confronted with many measurements at different sites. It is concluded that the stiffness variation of the track and the soil generate an important ground vibration component near railway lines.
A simple and fast prediction scheme is presented for train-induced ground and building vibrations. For the emission, finite-element boundary-element or multiple-beam-on-continuous-soil models of the track have been analysed and approximated by faster track-on-Winkler-soil models. The vehicle-track interaction due to irregularities yields the excitation forces. For the transmission of waves in the soil, the wavenumber integral of the compliance of layered soils has been evaluated. The calculation time is reduced for the prediction by using the solution of a homogeneous half-space with a frequency-dependent wave velocity (the dispersion) of the soil. For the immision, many 2 and 3-dimenisonal finite-element building models have been investigated, and a good approximation has been established by a 1-dimensional soil-wall-floor model. In addition, the axle sequence of the train, the quasi-static and the “scattered” response of the soil, and the wave propagation from a tunnel to a pile foundation of a building have been included.
This talk provides a brief overview on some geomechanical phenomena and problematic issues in the field of offshore wind-energy geotechnics, with reference to their associated challenges for a numerical analysis/simulation. These may include large deformations, fluid coupling and grain-scale phenomena, all of which are generally difficult to be addressed with conventional FE techniques.
These challenges are illustrated here with a practical example for the retrofit of axially loaded piles using compaction grouting techniques. In this case, the mechanical effects of the retrofit may be analysed with standard FE techniques, but require the adoption of strong assumptions, while the injection process itself can only be analysed with special techniques such as the MPM.
Finally, an LBM-DEM framework for the micromechanical analysis of such problems is introduced and a practical application for the estimation of the soil resistance to driving (SRD) in layered profiles is discussed.