4 Material und Umwelt
Filtern
Dokumenttyp
- Vortrag (18)
- Posterpräsentation (8)
- Zeitschriftenartikel (3)
- Buchkapitel (2)
- Beitrag zu einem Tagungsband (1)
- Forschungsbericht (1)
- Forschungsdatensatz (1)
Referierte Publikation
- nein (34) (entfernen)
Schlagworte
- Per- and Polyfluoroalkyl substances (PFAS) (9)
- Sewage sludge (7)
- XANES spectroscopy (7)
- Soil (6)
- Düngemittel (5)
- PFAS (5)
- Phosphorus (5)
- Bottom ash (4)
- Combustion Ion Chromatography (4)
- Fertilizer (4)
Organisationseinheit der BAM
- 4 Material und Umwelt (34)
- 4.3 Schadstofftransfer und Umwelttechnologien (25)
- 4.4 Thermochemische Reststoffbehandlung und Wertstoffrückgewinnung (15)
- 1 Analytische Chemie; Referenzmaterialien (2)
- 1.1 Anorganische Spurenanalytik (2)
- 1.7 Organische Spuren- und Lebensmittelanalytik (2)
- 1.8 Umweltanalytik (1)
Eingeladener Vortrag
- nein (18)
Antimony in incineration bottom ash – Leaching behavior and conclusions for treatment processes
(2020)
Antimony (Sb) is used in industrial products mainly as flame retardant in plastic material. Due to such additives in plastics, about a half of Sb ends up in municipal solid waste incineration at the end-of-life and consequently in relevant amounts in the generated bottom ash. In contact with water, the initial leachability is low, as antimonates form sparingly soluble compounds with Ca2+. Following the carbonation of the incineration bottom ash (IBA) during the proceeding ageing the pH in the leachates decreases. With decreasing concentration of Ca in the eluate the solution equilibrium changes and antimonates dissolve. In Germany it is intended to regulate Sb in IBA with the planned implementation of the so called Mantelverordnung (MantelVO, containing provisions on the utilisation of mineral waste) in the near future. The limit values set in the draft might be critical for IBA and therefore pose a risk for the utilisation of the mineral fraction of IBA in the well-established recycling routes.
Die agronomische Effizienz von Düngemitteln wird üblicherweise im Vegetationsversuch geprüft. Vegetationsversuche erlauben die Betrachtung unterschiedlicher Kulturpflanzen und deren Strategien der Nährstoffmobilisierung und -Aneignung ebenso wie die Berücksichtigung verschiedener Substrattypen und deren Eigenschaften hinsichtlich Nährstofffixierung und -freisetzung. Solche Versuche, selbst wenn sie nicht im Feld, sondern nur im Gefäß durchgeführt werden, sind jedoch sowohl zeit- als auch kostenintensiv. In erster Näherung wird die Pflanzenverfügbarkeit insbesondere von Phosphor (P)-Düngemitteln daher herkömmlicherweise mit Hilfe standardisierter chemischer Extraktionsmethoden abgeschätzt, deren Durchführung in der deutschen ebenso wie in der europäischen Düngemittelverordnung normiert ist. Diese Methoden werden auch im Rahmen der staatlichen Düngemittelverkehrskontrolle genutzt, um die Einhaltung düngemittelrechtlicher Vorgaben zu überprüfen. Wie jüngere Arbeiten gezeigt haben, ist jedoch die Übertragung herkömmlicher Standardextraktionsmethoden auf neue Dünger aus Recyclingmaterialien wie Klärschlamm mit einigen Schwierigkeiten verbunden. Korrelationen zwischen P-Aufnahme im Vegetationsversuch und chemischer Löslichkeit im Standardextrakt sind oft nur mäßig bis schwach oder überhaupt nicht signifikant. Die vorliegende Literaturübersicht gibt einen Überblick zum aktuellen Stand des Wissens über die chemische Löslichkeit von klärschlammbasierten P-Recyclingdüngern, deren Effizienz im Vegetationsversuch und statistische Relationen zwischen beiden Parametern. Anschließend werden alternative Methoden
zur Abschätzung der P-Verfügbarkeit von Recyclingdüngern vorgestellt, die derzeit Gegenstand der wissenschaftlichen Diskussion sind.
Die agronomische Effizienz von Düngemitteln wird üblicherweise in Vegetationsversuchen geprüft. Diese erlauben die es, unterschiedliche Kulturpflanzen und deren Strategien der Nährstoffmobilisierung und -aneignung zu betrachten und verschiedene Substrattypen und deren Eigenschaften im Hinblick auf Nährstofffixierung und -freisetzung zu berücksichtigen. Solche Versuche, selbst wenn sie nicht im Feld, sondern nur im Gefäß durchgeführt werden, sind jedoch sowohl zeit- als auch kostenintensiv. In erster Näherung wird die Pflanzenverfügbarkeit insbesondere von Phosphor (P)-Düngemitteln daher in der Regel mit Hilfe standardisierter chemischer Extraktionsmethoden abgeschätzt, deren Durchführung in der deutschen ebenso wie in der europäischen Düngemittelverordnung normiert ist. Diese Methoden werden auch bei der staatlichen Düngemittelverkehrskontrolle genutzt, um zu überprüfen, ob die düngemittelrechtlichen Vorgaben eingehalten werden. Wie jüngere Arbeiten gezeigt haben, ist es jedoch schwierig, herkömmliche Standardextraktionsmethoden auf neue Dünger aus Recyclingmaterialien wie Klärschlamm zu übertragen. Korrelationen zwischen P-Aufnahme im Vegetationsversuch und chemischer Löslichkeit im Standardextrakt sind oft nur mäßig bis schwach oder überhaupt nicht signifikant. Die vorliegende Literaturübersicht gibt einen Überblick zum aktuellen Stand des Wissens über die chemische Löslichkeit von klärschlammbasierten P-Recyclingdüngern, deren Effizienz im Vegetationsversuch und statistische Relationen zwischen beiden Parametern. Anschließend werden alternative Methoden zur Abschätzung der P-Verfügbarkeit von Recyclingdüngern vorgestellt, die derzeit Gegenstand der wissenschaftlichen Diskussion sind.
Wie können industriell synthetisierte Schadstoffe aus einer Stoffklasse quantifiziert werden, deren genauer Umfang unbekannt ist und auf mehrere tausend Verbindungen geschätzt wird? Im Falle der per- und polyfluorierten alkylierten Substanzen (PFAS) stellen sich Wissenschaftler*innen weltweit seit über zehn Jahren diese Frage. Neben der etablierten Methodik der Einzelstoffanalytik (engl. target analytic) existieren Summenparameteranalysen zur Quantifizierung
organisch gebundener fluorierter Verbindungen in Umweltmedien und Konsumprodukten. An der Bundesanstalt für Materialforschung und -prüfung (BAM) beschäftigen wir uns mit der Weiterentwicklung von Summenparametermethoden am Beispiel von PFAS-belasteten Umweltkompartimenten wie Böden, Klärschlämmen und Gewässerproben sowie PFAS-haltigen Konsumgütern. In diesem Beitrag stellen wir zwei ausgewählte Fallbeispiele vor und diskutieren die Vor- und Nachteile der Methoden im Vergleich zur Einzelstoffanalytik.
Due to its large mineral fraction, incineration bottom ash (IBA) from municipal solid waste incineration is an interesting raw material that can be used for road construction or to produce secondary building materials. However, leaching chloride, sulfate, and potentially harmful heavy metals may cause problems in using IBA in civil engineering. Investigating leaching behavior is crucial for the assessment of the environmental compatibility of IBA applications. Various test procedures are available for that purpose. In the present study, a long-term leaching test of a wet-mechanically treated IBA was performed in a lysimeter for almost six years.
While concentrations of chloride, sulfate and the majority of the heavy metals started to decrease rapidly with progressive liquid-to-solid ratio (L/S), antimony (Sb) and vanadium (V) behaved differently. At the beginning of the lysimeter test, the Sb and V concentrations were low, but after approximately one year of operation at an L/S ratio of around 0.8 L/kg, a steady increase was observed. It was shown that this increase is the result of low Ca concentrations due to the formation of CaCO3.
With the data, the solubility products from Ca-antimonate and Ca-vanadate were calculated. The unusual leaching behavior of Sb and V should be kept in mind when considering field scenarios and evaluating the impact on the environment.
Per- and polyfluoroalkyl substances (PFAS) are a large group of organofluorine surfactants used in the formulations of thousands of consumer goods, including aqueous film-forming foams (AFFF) used to suppress aviation fires in training scenarios, non-stick cookware, fast-food wrappers, water-repellent fabrics, medical equipment, and plastic and leather products. As a result of the perpetual use of PFAS containing products, effluents and sewage sludge from wastewater treatment plants (WWTPs) have been observed to be an important pathway for PFAS into the environment. In Germany, phosphorus and other nutrients from sewage sludge and wastewater should be recycled in WWTPs of cities with a large population. However, it is not clear if PFAS contamination from wastewater and sewage sludge end up in novel wastewater-based fertilizers. Normally, PFAS are analyzed using PFAS protocols typically with time-consuming extraction steps and LC-MS-MS quantification. However, for screening of PFAS contaminations in sewage sludge or wastewater-based fertilizers also passive sampler based on the Diffusive Gradients in Thin-films (DGT) technique can be used for the PFAS extraction. Afterwards, combustion ion chromatography (CIC) can be applied to analyse the “total” amount of PFAS on the passive sampler. Here, we show results from the DGT method in comparison to those of the extractable organic fluorine (EOF) method for a variety of wastewater-based fertilizers. Additionally, we analysed the adsorption of PFAS on the weak anion exchanger (WAX) based DGT passive sampler binding layer by infrared and fluorine K-edge X-ray adsorption near-edge structure (XANES) spectroscopy.
Per- and polyfluoroalkyl substances (PFAS) are a group of anionic, cationic and zwitterionic synthetic products, in which the hydrogen atoms on the carbon skeleton of at least one carbon atom have been completely replaced by fluorine atoms and which include more than 4730 compounds, depending on the definition. As a result of continuous and prolific use, mainly in aviation firefighting foams, thousands of industrial and military installations have been found to contain contaminated soil, groundwater and surface water. As a result of the perpetual use of PFAS containing products, effluents and sewage sludge from wastewater treatment plants (WWTPs) have been observed to be an important pathway for PFAS into the environment. In Germany, phosphorus and other nutrients from sewage sludge and wastewater should be recycled in WWTPs of cities with a large population. However, it is not clear if PFAS contamination from wastewater and sewage sludge end up in novel wastewater-based fertilizers. Normally, PFAS are analyzed using PFAS protocols typically with liquid chromatography tandem mass spectrometry (LC-MS/MS) quantification. To get a better overview of the amount of “total PFAS,” we applied sum parameter methods based on combustion ion chromatography (CIC) to screen the PFAS contaminations in various sewage sludge and wastewater-based fertilizers. Furthermore, current decontamination strategies of PFAS-burdened soils mainly consist of adsorption methods using adsorbents for fixation of PFAS in the ground. A second option is the utilization of a “pump and treat” process, cycling polluted soils through a washing plant leading to the concentration of the pollutants in the fine fraction. Only a subsequent, high-energy consuming pyrolysis process guarantees the total destruction of all fluorinated organic contaminants. Both approaches are cost-intensive and not intended for the direct decomposition of all PFAS contaminants. Hence, there is a great demand for innovative developments and chemical treatment technologies, dealing with new strategies of tackling the PFAS problem.
Per- und polyfluorierte Alkylsubstanzen (PFAS) im Klärschlamm - Analytische Methoden und Grenzwerte
(2022)
Per- und Polyfluoralkylsubstanzen (PFAS) sind eine Gruppe von mehr als 4700 anionischen und kationischen anthrophonen Stoffen, die aufgrund ihrer inerten chemischen Stabilität und ihrer Widerstandsfähigkeit gegen den Abbau durch Hitze oder Säuren in einer Vielzahl von Produkten verwendet werden. Infolge der ständigen Verwendung, vor allem in Feuerlöschschäumen für die Luftfahrt, wurden in Tausenden von Industrie- und Militäranlagen kontaminierte Böden und Grundwasservorkommen gefunden. Aufgrund der ständigen Verwendung von fluorierten Konsumgütern haben sich jedoch auch Abwässer und Klärschlamm aus Kläranlagen als Quelle für die Kontamination der aquatischen Umwelt mit PFAS erwiesen. Infolge der strengeren Vorschriften und Beschränkungen, die in den letzten Jahren für die Verwendung langkettiger (≥C8) PFAS erlassen wurden, findet in der chemischen Industrie eine deutliche Verlagerung hin zur Herstellung kurz- (C4-C7) und ultrakurzkettiger (C1-C3) Alternativen statt. Mit der Novellierung der Klärschlammverordnung im Jahr 2017 hat der deutsche Gesetzgeber die Ausbringung von Klärschlamm auf landwirtschaftlichen Flächen verboten, und bis 2029/2032 wird die Ausbringung von Klärschlamm in der Landwirtschaft vollständig verboten sein. Während die Belastung der Umwelt mit organischen Schadstoffen wie PFAS, Pestiziden und Arzneimitteln nicht mehr erwünscht ist, muss Phosphor (P) aus Klärschlamm weiterhin zur Herstellung hochwertiger P-Dünger für eine Kreislaufwirtschaft genutzt werden. Derzeit können pflanzenverfügbare P-Düngemittel aus Klärschlamm/Abwasser mit verschiedenen Behandlungsmethoden hergestellt werden, darunter Fällung, Auslaugung und thermische Behandlung. Der Verbleib von PFAS bei der Auslaugung, Ausfällung und Behandlung von Klärschlamm und Abwasser ist jedoch noch weitgehend unbekannt.
Dust deposition is an important source of phosphorus (P) to many ecosystems. However, there is little evidence of dust-derived P-containing minerals in soils. Here we studied P forms along a well-described climatic gradient on Hawaii, which is also a dust deposition gradient. Soil mineralogy and soil P forms from six sites along the climatic gradient were analyzed with bulk (X-ray diffraction and P K-edge X-ray absorption near edge structure)
and microscale (X-ray fluorescence, P K-edge X-ray absorption near edge structure, and Raman) analysis methods. In the wettest soils, apatite grains ranging from 5 to 30 μm in size were co-located at the micro-scale with quartz, a known continental dust indicator suggesting recent atmospheric deposition. In addition to colocation with quartz, further evidence of dust-derived P included backward trajectory modeling indicating that dust particles could be brought to Hawaii from the major global dust-loading areas in central Asia and northern Africa. Although it is not certain whether the individual observed apatite grains were derived from long-distance transport of dust, or from local dust sources such as volcanic ash or windblown fertilizer, these observations offer direct evidence that P-containing minerals have reached surface layers of highly-weathered grassland soils
through atmospheric deposition.
A wide range of analytical methods are used to estimate the plant-availability of soil phosphorus (P). Previous investigations showed that analytical methods based on the Diffusive Gradients in Thin films (DGT) technique provide a very good correlations to the amount of bioavailable nutrients and pollutants in environmental samples (Davison 2016, Vogel et al. 2017). However, the DGT results do not identify which P compound of the soil has the high bioavailability. But there are various spectroscopic techniques (infrared, Raman, P K-edge and L-edge XANES and P NMR spectroscopy) available to characterize P species in soils. Therefore, spectroscopic investigation of DGT binding layers after deployment allow us to determine the specific compounds. Nutrients such as phosphorus and nitrogen are often, together with other elements, present as molecules in the environment. These ions are detectable and distinguishable by infrared, P K- and L-edge X-ray absorption near-edge structure (XANES) and NMR spectroscopy, respectively. Additionally, microspectroscopic techniques make it also possible to analyze P compounds on the DGT binding layer with a lateral resolution down to 1 μm2. Therefore, species of elements and compounds of e.g. a spatial soil segment (e.g. rhizosphere) can be mapped and analyzed, providing valuable insight to understand the dynamics of nutrients in the environment.
The aim of this study was to investigate the passive sampler method Diffusive Gradients in Thin-films (DGT) for ammonium and nitrate in amended soils. Therefore, we used soils from a pot experiment with maize where nitrogen (N) was supplied as ammonium sulfate nitrate (ASN), without and with a nitrification inhibitor (NI). The additional use of a NI can delay the nitrification in the soil and making the ammonium available for a longer period in the soil solution after its application. Homogenized soil samples were collected directly from each pot after one week of incubation before sowing and after harvesting the maize. Nitrate and ammonium in these soil samples were extracted using DGT devices equipped with a Putolite A520E (for nitrate) and Microlite PrCH (for ammonium) binding layer. Ammonium DGT which determined the mobile and labile ammonium forms based on diffusion and the resupplies from the solid soil phase, only showed a significantly higher amount of extractable ammonium with NI compared to that without NI for some samples. However, significantly lower values were found for nitrate of treatments with NI compared to without NI after harvest. Thus, the lower nitrate amounts for treatments with NI compared to the treatments without NI after harvest indicated the delay of the nitrification process by the NI. Furthermore, we compared also the ammonium and nitrate
DGT results to chemical extraction with KCl solutions. The results demonstrated that the trends of DGT results and chemical extraction were complimentary through all the treatments.
Phosphorus (P) fertilizers from secondary resources became increasingly important in the last years. However, these novel P-fertilizers can also contain toxic pollutants. Chromium in its hexavalent state (Cr(VI)) is regulated with low limit values for agricultural products due to its high toxicity, but the determination of Cr(VI) in these novel fertilizer matrices can be hampered by redox processes that lead to false results. Thus, we applied the passive sampler technique Diffusive Gradients in Thin-films (DGT) for the determination of Cr(VI) in fertilizers and compared the results with the standard wet chemical extraction method (German norm DIN EN 15192) and Cr K-edge X-ray absorption near-edge structure (XANES) spectroscopy. We determined an overall good correlation between the wet chemical extraction and the DGT method. DGT was very sensitive and in most cases selective for the analysis of Cr(VI) in P-fertilizers. However, hardly soluble Cr(VI) compounds cannot be detected with the DGT method since only mobile Cr(VI) is analyzed. Furthermore, Cr K-edge XANES spectroscopy showed that the DGT binding layer also adsorbs small amounts of mobile Cr(III) compounds which leads to overestimated Cr(VI) values. The results of certain types of P-fertilizers containing mobile Cr(III) or partly immobile Cr(VI), showed that optimization of the DGT method is required to avoid over- or underestimation of Cr(VI).
Per- and polyfluoroalkyl substances (PFAS) have been used extensively in the past because of their inert chemical character and resistance to degradation by environmental influences. Since the beginning of their commercial use, PFAS have been widely exposed to the environment by application of PFAS in consumer products or as foaming agent in firefighting foams, thus several cases of contaminated soils sites have been reported. Since the number of known PFAS already exceeds 4700, their characterization and direct analysis is challenging given the current available techniques. Here, we introduce the novel fluorine (F) K-edge X-ray absorption near-edge structure (XANES) spectroscopy as a tool to analyze PFAS and inorganic fluorine compounds in contaminated soils and sewage sludges. While F K-edge bulk-XANES spectroscopy provide us information on the overall fluorine bonding in a sample micro X-ray fluorescence (XRF) in combination with F K-edge micro-XANES spectroscopy can also detect minor fluorine compounds and PFAS hotspots in investigated soils and sludges. Additionally, we used the combustion ion chromatography (CIC) to analyze the total amount of all PFAS as a sum parameter (extractable organic fluoride: EOF) in soils and sewage sludges. During combustion in the CIC, the PFAS in the sample get destroyed at temperatures of approx. 1000 °C and converted in inorganic fluorides that subsequently gets quantified by ion chromatography. Thus, for the first time we successfully combined F K-edge XANES spectroscopy and CIC as analytical tools to detect and quantify PFAS contaminants in soils and sewage sludges.
Analytical Challenges for PFAS in Environmental Samples - Methods, Approaches and Applicability
(2022)
Per- and polyfluoroalkyl substances (PFAS) are anionic, cationic and zwitterionic synthetic products, in which the hydrogen atoms on the carbon skeleton of at least one carbon atom have been completely replaced by fluorine atoms and which include up to 1.7 M compounds, depending on the definition. As a result of continuous and prolific use, mainly in aviation firefighting foams, thousands of industrial and military installations have been found to contain contaminated soil, groundwater and surface water. Furthermore, because of the continuous contamination through PFAS containing commercial products, effluents and sewage sludge from WWTPs have been shown to be an important source of PFAS discharge into the aquatic environment. In the last few years, legacy PFAS (≥C4) have been found in various environments, including soil, water and wastewater, and their environmental pathways have been partly described.
Several long-chain PFAS species, and their respective salts are considered as persistent organic pollutants by the United Nations Stockholm Convention. These pollutants have been linked to altered immune and thyroid function, liver disease, lipid and insulin dysregulation, kidney disease, adverse reproductive and developmental outcomes, and cancer. A significant shift in the chemical industry towards production of short (C4-C7) and ultrashort (C1-C3) alternatives was observed in response to recently intensified regulations and restrictions on the use of long-chain (≥C8) PFAS. PFAS analysis in environmental samples is currently mainly done by liquid chromatography tandem mass spectrometry (LC-MS/MS). This efficient method is conducted in a targeted fashion analyzing a small subset of PFAS. The US EPA method for analysis of PFAS using LC-MS/MS for example currently lists 40 PFAS (≥C4). However, to get a better overview of the amount of “total PFAS,” sum parameter methods like total oxidizable precursor (TOP) assay and methods based on combustion ion chromatography (CIC) are in development. CIC results in data regarding the sum of absorbable organic fluorine (AOF) or extractable organic fluorine (EOF), which can also quantify other organically bound fluorine compounds such as fluorinated pesticides and pharmaceutical. Moreover, non-target and suspect screening mass spectrometry can be used to identify novel emerging PFAS and partly unknown fluorinated compounds in environmental samples. Furthermore, to analyze ultrashort PFAS (C1-C3), supercritical fluid chromatography (SFC), hydrophilic interaction chromatography (HILIC) and gas chromatography-mass spectrometry (GC-MS) are available, but further research is needed to develop reliable and accurate methods to quantify several ultrashort PFAS in environmental samples.
Additionally, for research purpose several spectroscopical methods like X-ray photoelectron spectroscopy (XPS), fluorine K-edge X-ray absorption near-edge structure (XANES)spectroscopy, particular induced gamma-ray emission (PIGE) spectroscopy and 19F nuclear magnetic resonance (NMR) spectroscopy are available.
Per- and polyfluoroalkyl substances (PFAS) are a large group of anionic, cationic, or zwitterionic organofluorine surfactants used in the formulations of thousands of products and consumer goods, including aqueous film-forming foams (AFFF) used to suppress aviation fires in training scenarios, non-stick cookware, fast-food wrappers, water-repellent fabrics, medical equipment. Because PFAS have been extensively used in a variety of AFFF products they can be found in soils from industrial and military installations. Current decontamination strategies of PFAS-burdened soils mainly consist of adsorption methods using adsorbents for fixation of PFAS in the ground. A second option is the utilization of a “pump and treat” process, cycling polluted soils through a washing plant leading to the concentration of the pollutants in the fine fraction. Only a subsequent, high-energy consuming pyrolysis process guarantees the total destruction of all fluorinated organic contaminants. Both approaches are cost-intensive and not intended for the direct decomposition of all PFAS contaminants. Hence, there is a great demand for innovative developments and chemical treatment technologies, dealing with new strategies of tackling the PFAS problem. Previously, mechanochemical treatment of polychlorinated organic compounds in soils showed an efficient dechlorination. Thus, we investigated mechanochemical treatment of PFAS contaminated soils with various additives in a ball mill and analyzed the PFAS defluorination with gas chromatography mass spectrometry (GCMS) and liquid chromatography tandem mass spectrometry (LC-MS/MS), respectively, as well es the fluoride mineralization by ion chromatography (IC) and fluorine K-edge X-ray absorption near-edge structure (XANES) spectroscopy.
Per- and polyfluoroalkyl substances (PFAS) are anionic, cationic and zwitterionic synthetic products, in which the hydrogen atoms on the carbon skeleton of at least one carbon atom have been completely replaced by fluorine atoms (see Figure 1) and which include more than 4730 compounds, depending on the definition. As a result of continuous and prolific use, mainly in aviation firefighting foams, thousands of industrial and military installations have been found to contain contaminated soil, groundwater and surface water. Furthermore, because of the continuous contamination through PFAS containing commercial products, effluents and sewage sludge from WWTPs have been shown to be an important source of PFAS discharge into the aquatic environment. In the last few years, legacy PFAS (≥C4) have been found in various environments, including soil, water and wastewater, and their environmental pathways have been partly described. To get a better
overview of the amount of “total PFAS,” sum parameter methods like total oxidizable precursor (TOP) assay and methods based on combustion ion chromatography (CIC) are in development. CIC results in data regarding the sum of absorbable organic fluorine (AOF) or extractable
organic fluorine (EOF), which can also quantify other organically bound fluorine compounds such as fluorinated pesticides and pharmaceutical. Additionally, for research purpose several spectroscopical methods like X-ray photoelectron spectroscopy (XPS), fluorine K-edge X-ray absorption near-edge structure (XANES) spectroscopy, particular induced gamma-ray emission (PIGE) spectroscopy and 19F nuclear magnetic resonance (NMR) spectroscopy are available. Therefore, an overview is given on various analytical techniques for PFAS in environmental samples and their application possibilities discussed for different kind of PFAS compounds
Recycling-Düngemittel auf Basis von sekundären Ressourcen (Gülle, Gärreste, Klärschlamm, Tiermehl etc.) gewinnen in den letzten Jahren zunehmend an Bedeutung in der Landwirtschaft. Die in den Recycling-Düngemitteln enthaltenen P-Spezies weichen oft stark von denen in konventionell hergestellten Düngemitteln aus Rohphosphat ab, zudem enthalten Recyclingdünger oft mehrere verschiedene P-Formen. Die Pflanzenverfügbarkeit des P in ist ganz wesentlich von der enthaltenen P-Form abhängig. Derzeit gibt es außer zeitaufwendigen und kostspieligen Gefäß- und Feldversuchen keine zufriedenstellende Testmethode zur Analyse der P-Pflanzenverfügbarkeit von unterschiedlichen Recycling P-Düngemitteln. Die im europäischen Düngemittelrecht normierten chemischen Extraktionsmethoden (Wasser, Zitronensäure, Ameisensäure, neutral Ammoniumcitrat etc.) zeigen oftmals keine oder nur sehr geringe Korrelation zu der P-Aufnahme von Pflanzen in Gefäßversuchen mit Recycling-Düngemitteln (Kratz et al. 2010, Steckenmesser et al. 2017, Vogel et al. 2017). Eine grundlegende Schwäche chemischer Extraktionsmethoden liegt darin, dass es sich dabei um statische Methoden handelt, die nicht in der Lage sind, die im System Boden/Düngemittel-Bodenlösung-Pflanze stattfindenden dynamischen Prozesse wie P-Freisetzung und Entzug durch die Pflanzenwurzeln abzubilden.
Einen Lösungsansatz bieten hier sog. P-Senken-Methoden. Bereits in den 1950er Jahren wurden erstmals P-Senken zur Analyse des Boden-P angewendet (Chardon et al. 1996). In den darauffolgenden Jahrzehnten wurden verschiedene P-Senken auf der Basis von Eisenoxid-Papier entwickelt (Chardon et al. 1996). Jedoch konnten diese Ansätze auch nur begrenzt zur Bestimmung der P-Pflanzenverfügbarkeit des Boden-P eingesetzt werden. Mitte der 1990er Jahre wurde die DGT (engl. diffusive gradients in thin films) Methode entwickelt (Zhang et al. 1998). Bei der DGT Methode diffundiert P aus der Bodenlösung des angefeuchteten Bodens durch einen Membranfilter und die Diffusionsschicht und wird anschließend an einer Bindungsschicht absorbiert. Durch den Diffusionsgradienten wird das Gleichgewicht in der Bodenlösung permanent gestört, wodurch auch labiles P im Boden gelöst wird. Die stetige Entnahme von P aus der Bodenlösung über die Diffusions-/Bindungsschicht simuliert dabei den Entzug von P durch die Pflanzenwurzel. Die an die Bindungsschicht adsorbierte Menge an P korreliert stark mit der P-Aufnahme von Pflanzen (u.a. Mason et al. 2005, 2013; Menzies et al. 2005, Six et al. 2012). Im Gegensatz zu chemischen Extraktionsmethoden werden bei der DGT Methode Mischungen an Düngemittel und Boden für mehrere Tage inkubiert (Vogel et al. 2017; Duboc et al. 2017), da ansonsten wasserlösliche P-Dünger den DGT Adsorber sättigen und wasserunlösliche P-Dünger unterschätzt werden. Ein bis zwei Wochen Inkubation sind ausreichend, damit sich pflanzenverfügbares P in die Mischungen bildet.
In letzter Zeit haben verschiedene Forschungsgruppen gezeigt, dass die DGT Methode auch eine sehr gute Korrelation mit der Pflanzenverfügbarkeit verschiedener Typen von (Recycling-)P-Düngemitteln aufweist (Vogel et al. 2017; Duboc et al. 2017; Foereid 2017; Haarstad and Bavor 2017; Lemming et al. 2017). Bei Gefäßversuchen mit verschiedenen Recycling P-Düngemitteln konnte die DGT Methode den Ertrag bzw. die P-Aufnahme von Mais deutlich besser vorhersagen als herkömmliche chemische Extraktionsmethoden (Vogel et al. 2017; Duboc et al. 2017).
Daher kann die DGT Methode im Vorfeld der Zulassung von neuen Düngermitteltypen als zuverlässige und robuste Methode zum Screening von Produktvarianten eines Düngemittelherstellers verwendet werden. Um dieses Messverfahren im Rahmen des Düngemittelrechts als Bewertungsinstrument für die Abschätzung der Pflanzenverfügbarkeit unterschiedlicher Düngemittel zu verwenden, muss es allerdings zunächst standardisiert werden. Zu diesem Zweck bietet sich der Einsatz eines „standardisierten“ Bodens bzw. Bodenrezepts an. Zur Kalibrierung der Methode im jeweiligen Labor könnten auch chemisch definierte P-Verbindungen mit bekannter Löslichkeit/Pflanzenverfügbarkeit als Referenz-substanzen verwendet werden.
Specific co-fertilization of nutrients can enhance their plant-availability and thus the yield of plants. To investigate this effect, we performed a pot experiment with three different P-fertilizers and ammonium nitrate sulfate as a co-fertilizer, without and with a nitrification inhibitor (NI), and analyzed the form of nitrogen (N) in the soil via novel X-ray spectroscopic method. The application of NI with the N fertilizer led to a higher dry matter yield of maize. Novel N K-edge micro-X-ray absorption near-edge structure (micro-XANES) spectroscopy identified that the application of a NI promotes the temporary formation of a non-exchangeable N in detectable hot-spots in the soil. The subsequent slow release and prolonged availability of N during plant growth leads to higher yield. It can be concluded that NIs lead to a temporary fixation of ammonium-N in a pool that can be accessed by plant roots. Those types of available nutrient pools meet the idea of so-called “next generation fertilizers” as plants have access to nutrients according to their current demand.
Previous research shows that analytical methods based on Diffusive Gradients in Thin films (DGT) provide very good correlations to the amount of bioavailable nutrients and pollutants in the environmental samples. However, these DGT results do not identify which compound of the specific element has the high bioavailability. Using various spectroscopic techniques (infrared, XANES and NMR spectroscopy) to analyze the dried DGT binding layers after deployment could allow us to determine the specific elements or compounds. Nutrients such as phosphorus and nitrogen are often, together with other elements, present as molecules in the environment. These ions are detectable and distinguishable by infrared and NMR spectroscopy, respectively. In addition, XANES spectroscopy allows for the specification of nutrients and pollutants (e.g. chromium) on the DGT binding layer. Furthermore, microspectroscopic techniques make it also possible to analyze compounds on the DGT binding layer with a lateral resolution down to 5 µm2. Therefore, species of elements and compounds of e.g. a spatial soil segment can be mapped and analyzed, providing valuable insight to understand the dynamics of nutrients and pollutants in the environment. Here we will present the advantages and limitations of this novel combination of techniques.
Phosphorus (P) fertilizers from secondary resources became increasingly important in the last years. However, these novel P-fertilizer can also contain toxic pollutants e.g. chromium (Cr) in the hexavalent state (Cr(VI)), which is regulated with low limit values in agricultural products (German fertilizer ordinance limit: 2 mg/kg Cr(VI)). The determination of Cr(VI) in these novel fertilizer matrices can be hampered by redox processes that lead to false results with the standard wet chemical extraction method (German norm DIN EN 15192). Therefore, we analyzed Cr(VI) in various P-fertilizers with the DGT technique. DGT devices equipped with a APA (polyacrylamide) diffusion layer and Cr(VI) selective N-methyl-D-glucamine (NMDG) binding layer were used for the study. After a 24 h conditioning period of the fertilizer at 60% of the water holding capacity (WHC), the fertilizers were brought to 100% WHC, transferred onto the DGT devices and deployed for 24 h at 25°C. The extraction of Cr from the DGT binding layer was carried out with 1 M HNO3 for 24 h. The Cr-concentrations of the extract were determined by means of ICP-MS. We found a good correlation between the standard wet chemical extraction and the DGT method for the whole range of P-fertilizers. However, partly soluble Cr(VI) compounds cannot be detected in full extent by the DGT method that is best suited for mobile Cr(VI). Furthermore, Cr K-edge XANES spectroscopy showed that the Cr(VI)-selective DGT binding layer also adsorbs mobile Cr(III) compounds from acid treatment of phosphates which can therefore cause an overestimation of Cr(VI). The DGT method was very sensitive and in most cases selective for the analysis of Cr(VI) in P-fertilizers made from recycled materials. However, the results of certain types of P-fertilizers containing mobile Cr(III) or partly immobile Cr(VI) show that still some optimization of the method is required to avoid over- or underestimation of Cr(VI).