Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (61) (entfernen)
Sprache
- Englisch (33)
- Deutsch (22)
- Mehrsprachig (6)
Schlagworte
- Rheology (14)
- Rheologie (6)
- Cement (5)
- Concrete (5)
- Betoninstandsetzung (4)
- Geopolymers (4)
- Instandsetzung (4)
- Self-compacting concrete (4)
- Alkali-activation (3)
- Beton (3)
- Polycarboxylate ether (3)
- Rice husk ash (3)
- Selbstverdichtender Beton (3)
- Superplasticizers (3)
- Accelerated carbonation (2)
- Admixtures (2)
- Baustoffe (2)
- Engineered recycled mineral admixtures (2)
- Frischbetoneigenschaften (2)
- Geringer fester Beton (2)
- Instandsetzungsmörtel (2)
- One-part formulation (2)
- Polymer cement concrete (PCC) (2)
- Polysaccharides (2)
- Proficiency testing (2)
- Quality control (2)
- Reinforcement (2)
- Repair mortar (2)
- Repair systems (2)
- Robustheit (2)
- Robustness (2)
- Round robin (2)
- SCC (2)
- SVB (2)
- Sprayed polymer cement concrete (SPCC) (2)
- Spritzmörtel (2)
- Stabilising agent (2)
- Starch ether (2)
- Strength (2)
- Temperatur (2)
- Temperature (2)
- Urban heat island (2)
- Wasserbau (2)
- Workability (2)
- Yield stress (2)
- ZTV-LB 219 (2)
- Zusatzmittel (2)
- (Reinforced) concrete (1)
- AOQL (1)
- Acid resistance (1)
- Acoustic emission analysis (1)
- Africa (1)
- Ageing (1)
- Alkali activated materials (1)
- Alkali-activated materials (1)
- Allgemeines (1)
- Alterung (1)
- Ausführung (1)
- Basic oxygen furnace slag (1)
- Bauausführung (1)
- Baustellenanwendung (1)
- Betonglasrestaurierung (1)
- Betonpflasterstein (1)
- Betonpflastersteine (1)
- Betontechnologie (1)
- Bio-based concrete (1)
- Bio-based materials (1)
- Biopolymers (1)
- Blended cement (1)
- Box-Behnken (1)
- Brick clay (1)
- C3A (1)
- CFD simulation (1)
- CO2 reduction (1)
- CUSUM (1)
- Calcined clay (1)
- Carbonation behaviour (1)
- Casting (1)
- Cement testing (1)
- Cementitious materials (1)
- Chemical admixtures (1)
- Church windows (1)
- Churches (1)
- Coarsely dispersed systems (1)
- Compressive strength (1)
- Computertomografie (1)
- Concrete 3D-printing (1)
- Concrete block technique (1)
- Concrete paving stone (1)
- Concrete rehabilitation (1)
- Conformity (1)
- Control charts (1)
- Cracks (1)
- Cusum method (1)
- DIBt (1)
- DIN EN 1504 (1)
- Dalle de verre (1)
- Decision matrix analysis (1)
- Design of experiment (1)
- Diutan gum (1)
- EN 12350-11 (1)
- EN 206 (1)
- EN 206:2014 (1)
- Early cement hydration (1)
- Europäische Normungsarbeit (1)
- Evaporite rock (1)
- Festigkeit (1)
- Fibers (1)
- Fibre optic sensors (1)
- Fließmittel (1)
- Fließmittel Betontechnologie (1)
- Flow of concrete (1)
- Flow of mortar (1)
- Fly ash (1)
- Fresh concrete (A) (1)
- Frühe Zementhydratation (1)
- Funkenarmes Werkzeug (1)
- Funkenfreies Werkzeug (1)
- Glass (1)
- Grouted connection (1)
- Grouting (1)
- HRWRA (1)
- High-temperature treatment (1)
- Hitzeinsel (1)
- Hochleistungsbeton (1)
- Hydration (1)
- Hydration kinetics (1)
- Illitic clay (1)
- Instandsetzungsprinzipien (1)
- Instandsetzungssysteme (1)
- Iron ore tailings (1)
- KUSUM (1)
- Kalksteinmehl (1)
- Konformität (1)
- Kontrollkarten (1)
- Laserbasierte Rautiefebestimmung (1)
- Limestone (1)
- Limestone filler (1)
- Mean value criterion (1)
- Mechanisch erzeugte Funken (1)
- Metakaolin (1)
- Microfiller (1)
- Microscopy (1)
- Microsilica (1)
- Mikrofiller (1)
- Mikrostruktur (1)
- Mining tailing (1)
- Mining tailings (1)
- Mischungsentwurf (1)
- Mix design (1)
- Mixture composition (1)
- Modeling (E) (1)
- Monocarboaluminate (1)
- Nachbehandlung (1)
- Nachweis der Wirksamkeit (1)
- Nepheline (1)
- Nichtelektrische Funken (1)
- Nichtelektrischer Explosionsschutz (1)
- No slump concrete (1)
- Non sparking tools (1)
- Nuclear magnetic resonance (1)
- Nuclear waste storage (1)
- Oberflächenschutzsysteme (1)
- Offshore (1)
- On-Site Application III (1)
- One-part geopolymers (1)
- Optische Verformungsanalyse (1)
- PCE-Based superplasticizer (1)
- Particle-bed binder jetting (1)
- Pavement (1)
- Performance tests (1)
- Permeability (C) (1)
- Planung (1)
- Plastic viscosity (1)
- Polycarboxylate (1)
- Polycarboxylate ether vicat (1)
- Polycarboxylatether (1)
- Polymer-Zement Beton (PCC) (1)
- Polymer-Zement Spritzbeton (SPCC) (1)
- Porous medium (1)
- Praxis (1)
- Prüfverfahren (1)
- Qualitätssicherung (1)
- Rautiefe (1)
- Reaction products (1)
- Rehabilitation (1)
- Reibfunken (1)
- Repair (1)
- Rheology (A) (1)
- Schadensmechanismen (1)
- Schallemission (1)
- Schlagfunken (1)
- Schleiffunken (1)
- Schwinden (1)
- Sealing structures (1)
- Sedimentation (1)
- Selbstkühlend (1)
- Self-Compacting Concrete (1)
- Self-consolidating concrete (1)
- Self-cooling (1)
- Setting (1)
- Shear (1)
- Shewhart (1)
- Shrinkage (1)
- Siebtest (1)
- Silica (1)
- Simulation (1)
- Slump flow (1)
- Sphingan (1)
- Stabilising agents (1)
- Stahlfaserbeton (1)
- Stahlfasern (1)
- Starch (1)
- Static loading (1)
- Steel slag (1)
- Structural analysis (1)
- Sulfationengehalt (1)
- Sulphate ion content (1)
- Superplasticizer (1)
- Supplementary cementitious materials (1)
- Supplementary cementitous materials (1)
- Technische Regel (1)
- Thermal Analysis (1)
- Thermal analysis (1)
- Thermal behavior (1)
- Ultrahochleistungsbeton (1)
- Urban heat island effect (1)
- Versuche (1)
- Vicat (1)
- Viscosity (1)
- Viscosity modifying agents (1)
- Wastepaper sludge ash (1)
- Zement (1)
- Zeolite A (1)
- Zeolites (1)
- Zeta potential (1)
- Zugbeanspruchung (1)
- analysis (1)
- blended cements (1)
- pH-indicators (1)
- recycled material (1)
- thermal methods (1)
Organisationseinheit der BAM
Paper des Monats
- ja (2)
Polysaccharides provide high potential to be used as rheology modifying admixtures in mineral binder systems for the construction industry such as concrete or mortar. Since superplasticizers have become state of technology, today, concrete is more and more adjusted to flowable consistencies. This often goes along with the risk of segregation, which can be effectively avoided by adding stabilising agents supplementary to superplasticizers. Stabilising agents are typically based on polysaccharides such as cellulose, sphingan gum, or starch. Starch clearly distinguishes in its effect on rheology from other polysaccharides, mainly due to the strong influence of amylopectin on the dispersion and stabilisation of particles. Based on rheometric investigations on cementitious and limestone based dispersions with different volumetric water to solid ratios, the mode of operation of modified potato starch is explained in comparison to a sphingan gum. It is shown that the stabilising effect of starch in a coarsely dispersed system is mainly depending upon the water to solid ratio and that above a certain particle volume threshold starch mainly affects the dynamic yield stress of dispersions, while plastic viscosity is affected only to a minor degree. Sphingans operate more independent of the particle volume in a coarsely dispersed system and show significantly higher effect on the plastic viscosity than on the yield stress. In systems incorporating superplasticizers, influences of both stabilising agents on yield stress retreat into the background, while both observed polysaccharides maintain their effect on the plastic viscosity.
Seit Juli 2014 liegt die EN 206:2014 als neue Betonnorm vor. Neben kleineren Änderungen ergibt sich hierdurch als einschneidende Änderung zur Vorgängerversion EN 206-1:2008 ein ergänzendes Konzept zur Konformitätsbewertung der Druckfestigkeit von Beton. An dieser Stelle werden neben dem bekannten Mittelwertkriterium alternativ sogenannte Kontrollkartenverfahren möglich. Für die Konformitätsbewertung stellt in diesem Zusammenhang insbesondere die Kusum-Methode (kumulierte Summen, aus dem Englischen cusum – cumulative sum) ein Novum dar. Weiterführende Informationen zu Kusum-Methode in der Konformitätsbewertung können der Literatur entnommen werden. Eigentlich ist die Kusum-Methode aber nicht für die Konformitätsbewertung entwickelt worden, sondern vielmehr für die Produktionskontrolle. Der Unterschied zwischen Konformitätsbewertung und Produktionskontrolle ergibt sich daraus, dass die Konformitätskontrolle eine Bedeutung für die öffentliche Sicherheit hat und dass eindeutige technische Grenzwerte vorliegen müssen, die nicht unterschritten werden dürfen, während die Produktionssteuerung ein Werkzeug mit frei wählbaren Grenzwerten für Hersteller ist. Der Handlungsbedarf ist für die Produktionskontrolle optional und ergibt sich in der Regel aus Wirtschaftlichkeitsbetrachtungen.
African cement infrastructure is quite complex. Apart from Northern Africa and South Africa in particular, cement plants are scarce resulting in highly unstable cement pricing. Clinker and cement are imported from overseas, e.g. from Portugal, Turkey, Pakistan, Indonesia, and China. Imports are typically determined by the lowest price, and as a result the countries of origin of products vary regularly yielding large scatter of properties. Quality control and a good quality infrastructure are thus of utmost importance for the safety of the populace, an issue, which is actually often neglected. With funding of the German Metrology Institute (PTB) and support of the SPIN project, a proficiency testing scheme for cement testing according to EN 196 was set up for African laboratories. Proficiency testing schemes, also called round robins, are inter-laboratory performance comparisons allowing participants to evaluate themselves against pre-established criteria. They are a powerful tool to help laboratories improve their performance as well as demonstrate their competences to accreditation bodies or customers. 26 laboratories from 20 nations, 18 of which from Africa, participated. The BAM Federal Institute for Materials Research and Testing acted as coordinator and provider of the scheme. The aim of the round robin was to interpret the submitted data further beyond the pure statistic analyses. The data provided a positive picture of the performance of the participants in general, but it also exhibited a number of technical fields that need improvement. The paper provides the general results of the scheme and analyses identified strengths and weak points based on the submitted and non submitted data as well as on discrepancies from the EN 196 procedures during measurements. The application of EN standards for material testing is critically discussed and since quality infrastructure is also always an issue between industrial and political stakeholders, suggestions for the mitigation of the identified shared problems are given.
Innovative admixture technology has significantly widened up the ränge of possibilities of concrete engineers. For many decades the water to cement ratio (w/c) was the major influencing factor for the performance of concrete. Due to the need to adjust a consistency, which still allowed reasonable workability, the w/c was typically significantly higher than technologically reasonable. Rheology modifying admixtures Support adjusting the concrete consistency largely independent of the w/c. It was only after the invention of the first superplasticizers that modern concrete technology significantly evolved in terms of flowability, strength, and durability, and only due to the steady evolution of the technology modern innovations, such as Self-Compacting Concrete, Ultra-High-Performance Concrete, or Engineered Cementitious Composites were made possible. Today’s superplasticizers are extremely versatile and can be adjusted to individual technologicalspecifications. However, the other side of the coin of versatility is that cementitious Systems incorporating superplasticizers have become more sensitive against environmental influences, such as the environmental temperature, which may cause unwanted effects or demand for supplementary admixture use such as stabilizing admixtures. Hence, concrete mixture composition with admixtures demands for a high level of expertise and offen there is lack of awareness about the mode of Operation of rheology modifying admixtures among concrete technologists. The paper gives a comprehensive overview about rheology modifying admixtures such as superplasticizers or stabilizing agents, and how they can be used depending upon the application in the most favourable way. Based on experiences with the sub-Saharan African concreting boundary conditions, which exhibit many challenges in terms of environmental boundary conditions and construction site logistics, conclusions are finally drawn, how admixtures can be used in the most beneficial way to improve the concrete casting Situation.
Design : and use of engineered recycled mineral admixtures obtained from industrial and mineral waste are promising strategies to increase the range of materials suitable for use in cement-based composites. In this work, Portland cement-blended pastes containing mineral admixtures designed for improving particle packing were evaluated in the presence of low- and high-charge polycarboxylate-based superplasticizers. The powders were obtained from basic oxygen furnace slag, iron ore tailings, quartz mining tailings, and quartzite mining tailings. The zeta-potentials of the particles were obtained via electrophoretic mobility. The flow properties were evaluated by rheological tests performed in a Couette type rheometer. The hydration kinetics was evaluated by isothermal calorimetry and an adapted method based on the Vicat needle test. The high-charge PCE and the finer mineral admixtures produced more stable blends. Coarser mineral admixtures led to increased flowability and delayed hydration compared to finer ones. Steel slag powders presented the most significant plasticizer effects, but also the largest setting delays and segregation tendency. Quartz-rich superfines reduced the setting delays caused by the superplasticizers. In summary, both superplasticizers were effective in improving flow properties, but the high-charge PCE was effective in preventing segregation in pastes containing mineral admixtures coarser and heavier than cement.
While calcined clays in general have been credited with a great potential to mitigate CO2 emissions related to cement production and consumption, calcined brick clays are currently understudied in this regard. In the present work, two brick clays, a low-grade kaolinitic clay, and a mixed clay composed of 50% brick clay and 50% low-grade kaolinitic clay were studied regarding transformations on calcination, and strength and durability performance as well as pore structure of mortars made with the blended cements. All calcined clays exhibited pozzolanic reactivity, with the performance of the brick clays inferior to the low-grade kaolinitic clay. However, the mixed clay performed very similar to the low-grade kaolinitic clay, which points to a viable option for optimal use of brick clays in cementitious systems. The carbonation resistance of the blended cement mortars was generally worse than that of the plain Portland cement mortar, as expected, but the former exhibited a significantly improved chloride penetration resistance. The latter improvement was due to pore structure refinement in the blended cement mortars, compared to the Portland cement mortar.
The most common method for determination of the carbonation depth is the sprayed application of indicator solutions, Phenolphthalein in particular. Since the aerosols of Phenolphthalein are suspected to be carcinogenic, efforts have been intensified to use alternative indicators for the determination of carbonation depth. The subject and aim of this research paper are to examine indicator solutions from Alizarin Yellow R, Thymol Blue and a Mixed Indicator. These indicator solutions are commercially available and are not suspected to be carcinogenic.
For the purpose of this research, samples previously stored under accelerated carbonation conditions (1% CO2) were examined by thermogravimetric analysis (TGA) and examination of the pH value. Additionally, the electrolytic back-titration for determination of total CO2 amount was carried out comparatively to TGA.
Üblicherweise werden Werkzeuge für den industriellen Einsatz aus hochlegierten Chromstählen hergestellt. Für den Einsatz in explosionsgefährdeten Bereichen werden oft Werkzeuge aus speziellen Nichteisen-Metalllegierungen (NE-Metall) verwendet. Für diese sogenannten funkenarmen Werkstoffe und deren mögliche Schlagpartner gibt es bisher keine umfassenden Untersuchungen mit Aussagen zur Zündwahrscheinlichkeit.
Die TRGS 723, Abschn. 5.15, fordert den Nachweis der Funkenfreiheit der verwendeten Werkstoffpaarung. Jedoch sind Werkzeuge keine Geräte oder Schutzsysteme im Sinne der Richtlinie 2014/34/EU. Deshalb ist es nicht möglich, Werkzeuge in Übereinstimmung mit dieser Richtlinie zu zertifizieren. Der Nachweis der Erfüllung dieser Anforderungen ist durch Zertifizierungen im sogenannten "gesetzlich nicht geregelten" Bereich möglich. Die BAM bietet diese Zertifizierung für "Funkenarme Werkzeuge" im Rahmen ihres Zertifizierungsprogrammes an.
Die bisherigen Ergebnisse der hier vorgestellten Untersuchung haben gezeigt, dass es keine funkenfreien, metallischen Werkzeuge (non-sparking Tools) gibt. Entscheidend ist im Hinblick auf die TRGS 723, ob zündfähige Funken entstehen oder nicht. Es ist immer die Frage, worauf die Werkzeuge im praktischen Anwendungsfall schlagen oder fallen gelassen werden können, d.h. aus welchem Material der mögliche Schlagpartner besteht. Dies können metallische Schlagpartner, aber auch Betonoberflächen sein. Unterschiedliche Kombinationen von Werkstoffen ergeben bei Schlagbeanspruchung im explosionsgefährdeten Bereich jeweils unterschiedliche Zündwahrscheinlichkeiten. Aber auch die Höhe der beim Einsatz der Werkzeuge möglichen kinetischen Schlagenergie und der Brenngas/Luft-Atmosphäre im betreffenden explosionsgefährdeten Bereich sind wichtige Einflussgrößen.
Grouted connections are intensively used in offshore rigs, platforms as well as jacket and monopile offshore wind turbine structures. Being located in remote offshore conditions, these connections can experience considerable adverse loading during their lifetimes. Degradation was reported inside similar connections, which were installed in the last three decades. Grouting in the offshore sites may often be proven difficult, which eventually leads to reduced load-bearing capacity of connections in the long run. Thus, repair and rehabilitation of such connections should be planned ahead to minimize operational delays and costs. In this study, scaled grouted connections were manufactured using a novel mould, whose integrity were monitored using digital image correlation (DIC). The connections were loaded under static load to visualize the main failure pattern using distributed fibre optic sensors and acoustic emission (AE) analysis. Grouted connections were then repaired using a cementitious injectable grout. The effectiveness of the grout injection was monitored using dye penetration technique. Finally, specimens are reloaded to identify the potential of such repair for grouted connections.
Properties of alkali-activated mortars with salt aggregate for sealing structures in evaporite rock
(2021)
Concrete structures for sealing of tunnels in the host rock are an essential part of systems for nuclear waste storage. However, concretes based on blended cements or magnesium oxychloride cements, which are commonly considered for this application, can deteriorate severely due to a significant heat of hydration and associated deformation and cracking. Alkali-activated materials (AAMs) offer a potential solution to this problem because of their low heat release during hardening. To explore their suitability for the construction of sealing structures in evaporite rock, various AAMs with salt aggregate were studied regarding fresh properties, heat release, mechanical properties and microstructure. The heat of reaction of the AAMs was up to 55% lower than that of a blended cement designed for sealing structures, indicating significant benefits for the intended application. Other relevant properties such as mechanical strength and permeability depended strongly on the mix-design of the AAMs and curing conditions.