Filtern
Dokumenttyp
- Beitrag zu einem Tagungsband (6) (entfernen)
Sprache
- Englisch (6)
Referierte Publikation
- nein (6) (entfernen)
Schlagworte
- Adhesion (2)
- Ionic liquid (2)
- Composite materials (1)
- Composite structures (1)
- Composites (1)
- Distributed fibre optic sensors (1)
- Failure process (1)
- Fibre-matrix adhesion (1)
- Fluorescent polymer optical fibres (1)
- High voltage cable accessories (1)
- Morphology (1)
- Multifunctional epoxy (1)
- Multifunctional epoxy resin (1)
- Optical backscatter reflectometry (1)
- Optical fibre (1)
- Partial discharge detection (1)
- Polymer electrolyte (1)
- Self-healing (1)
- Silicone rubber (1)
- Single fibre pull-out test (1)
- Strength (1)
- Structural health monitoring (SHM) (1)
Polymer-based electrolytes based on commercially available epoxy resins were prepared through the addition of a liquid electrolyte, a solution of a lithium salt in an ionic liquid. The polymer monoliths were characterized using impedance spectroscopy, 3-point bending test, scanning electron microscopy (SEM) and nitrogen adsorption (BET). The balance of ionic conductivity and flexural modulus is crucially dependent on the relative proportions of epoxy resin to electrolyte. Also the effect of the liquid electrolyte on curing kinetics and processing was assessed by complex viscosity measurements and differential scanning calorimetry (DSC). Only one out of the three resins investigated exhibited a significant acceleration effect.
For the concept of using structural materials such as carbon fibre reinforced plastics as
energy storage devices, new matrix polymers are required. These polymers must provide ionic
conductivity as well as adequate mechanical strength. In the EU-Project StorAGE this
requirements are fulfilled by adding ionic liquid to commercial polymers. The mechanical
properties of these mixtures materials were characterized by using a 3-point-bending device.
In addition, single fibre pull test were performed in order to get information on the interfacial
shear strength. Adding of ionic liquid has an impact on the mechanical performance of the
materials. A decrease of the flexural strength and modulus of less than 10% of the value of the
reference materials took part. The interfacial shear strength decreased to a value of around
one third compare to the reference material.
To avoid a catastrophic failure of insulation in high-voltage (HV) applications, a monitoring of partial discharges (PDs) is necessary. Fluorescently labelled polymer optical fibers (F-POF) offer an electrically passive method for PD detection in HV facilities. F-POFs could be embedded in HV cable accessories, which are usually made of silicone rubber. Herein they detect the light emitted by the PD and convert it into an electrical signal that can be monitored. Due to the difficult accessibility of HV cable accessories, a self-healing silicone rubber with prolonged service life after PD detection represents an attractive material design for HV accessories. With this contribution, we would like to present and discuss the possibilities of combining self-healing materials with POF-based sensors for PD detection in HV applications.
Structural Health Monitoring of composite materials gains in importance with the increasing use of Composite structures for safety-related applications, e.g. in aerospace. Because of the material properties of composites, defects often occur inside the structures and raise the demand for integrated sensors. The advantages of optical fibres predestine them not only for the surface-application on composite structures but also for the Integration into composite structures. Even without quasi-distributed sensors such as FBGs or LPGs, the optical fibre itself can be used to measure the structure and occurring events over the entire fibre length by distributed sensing techniques. This paper presents the surface-application of polyimide coated silica optical fibres onto PEEK specimens and the integration of copper and polyimide coated silica optical fibres into an AS-4/PEEK Composite to be used as distributed fibre optic sensors for SHM. Results from distributed measurements by optical backscatter reflectometry based on Rayleigh backscattering are shown.
The strength of laminates distinctly depends on the transverse strength of the laminas. The transverse failure is dominated by the adhesion between fiber and matrix. Usual strength criteria however do not take into account the adhesive strength explicitly. The determination of the interface strength is performed on the micromechanical scale using single fiber specimens. The fibers are loaded under off-axis loading while the debonding is monitored under a microscope. The stresses acting in the Interface are calculated by finite element analyses. It is found that for off-axial angles up to 35° interfacial debonding is the dominant failure mode while fiber breakage takes place at lower angles. The occurrence of fiber breakage and debonding under off-axis loading shows that the restriction to two potential failure planes - perpendicular or parallel to the fibers - as applied in common failure criteria has to be put in question.