Ingenieurwissenschaften und zugeordnete Tätigkeiten
Filtern
Erscheinungsjahr
Dokumenttyp
- Beitrag zu einem Tagungsband (72) (entfernen)
Referierte Publikation
- ja (72) (entfernen)
Schlagworte
- Thermography (5)
- Additive manufacturing (4)
- Welding (4)
- Active thermography (3)
- Additive Manufacturing (3)
- FEM (3)
- Residual stress (3)
- Simulation (3)
- Ultrasound (3)
- Ageing (2)
Organisationseinheit der BAM
- 8 Zerstörungsfreie Prüfung (12)
- 8.0 Abteilungsleitung und andere (9)
- 9 Komponentensicherheit (7)
- 3 Gefahrgutumschließungen; Energiespeicher (4)
- 6 Materialchemie (4)
- 3.4 Sicherheit von Lagerbehältern (3)
- 8.5 Röntgenbildgebung (3)
- 9.4 Integrität von Schweißverbindungen (3)
- 5 Werkstofftechnik (2)
- 6.2 Material- und Oberflächentechnologien (2)
Enhanced photon upconversion using erbium-doped nanoparticles interacting with silicon metasurfaces
(2021)
Photon upconversion (UC) using trivalent erbium (Er+3) doped crystals is a promising concept to harness near infrared photons of the solar spectrum which cannot be directly absorbed by silicon solar cells. However, their UC efficiency at low-intensity 1 sun illumination is not relevant on device level so far. Exploiting giant near-field enhancement effects on metasurfaces is an appealing approach to enable efficient UC at low irradiance conditions. Here, we report on more than 1000-fold enhanced photon UC of NaYF4:Er+3 nanoparticles interacting with the near-fields supported by a silicon metasurface under 1550 nm excitation.
In this paper, we present a study aimed at characterizing the optimal fiber optic components for Brillouin sensing in multimode fibers. For this purpose the use of single-mode and multimode circulators as well as couplers typically used in the Brillouin measurement setups was investigated. On the one hand the undesired coupling losses between conventional fiber optic measurement system components and a multimode sensor fiber can be overcome by replacing the singlemode components with their own multimode equivalents. On the other hand the use of multimode fiber optic circulators and multimode couplers affects the mode distribution of laser light which can impair the measurement signal backscattered in the multimode sensor fibers. In view of an increasing interest in high strain measurements using polymer optical fibers (POFs) as Brillouin-distributed sensors the investigation on Brillouin scattering effects in multimode fibers (MMFs) was performed on a low-loss perfluorinated graded-index polymer optical fiber (PFGI-POF). The obtained results were compared with those of a standard graded-index multimode (GI-MMF) silica glass optical fiber (GOF).
This study confirms the relevance of the adaptation of the measurement system components to the use of the multimode sensor fibers. In addition, due to mode coupling effects occurring in the tested POF itself, the results show differences in the yield of the components adaptation in the sensory implementation of the two kinds of the tested optical fibers.
Due to the rapid thermal cycles involved in additive manufacturing of metals, high internal stresses and peculiar microstructures occur, which influence the parts mechanical properties. To systematically examine their formation, in-process measurements of the temperature are needed. Since the part emissivity is strongly inhomogeneous and rapidly changing in the process, the applicability of thermography for the determination of thermodynamic temperatures is limited. Measuring the thermal radiation in different wavelengths simultaneously, temperature and emissivity can be separated. Here, we present results of a preliminary study using multispectral thermography to obtain real temperatures and emissivities in directed energy deposition (DED) processes.
High-power laser beam welding became new stimuli within the last 10 years due to the availability of a new generation of high brightness multi kilowatt solid state lasers. In the welding research new approaches have been developed to establish reliable and praxis oriented welding processes meeting the demands of modern industrial applications during this time. The paper focuses on some of the current scientific and technological aspects in this research field like hybrid laser arc welding, simulation techniques, utilization of electromagnetic fields or reduced pressure environment for laser beam welding processes, which contributed to the further development of this technology or will play a crucial role in its further industrial implementation.
Microplastic detection in water samples becomes important for tracing microplastic sources. Microplastic may harm desalination facilities by blocking filters and disturbing the marine food chain. Thermo analytical methods such as pyrolysis gas chromatography mass spectroscopy, and spectroscopic methods like (micro) Raman spectroscopy or (micro) Fouriertransform infrared spectroscopy in combination with appropriate filters and sample preparation are suitable for analyzing microplastics on a scale from 1 µm to 1000 µm fast and unambiguous. While the thermo analytical methods are suitable for larger sample volumes, Raman spectroscopy and Fouriertransform infrared spectroscopy are able to detect and analyze single microplastic particles for instance in bottled water. Machine learning algorithms ensure a reliable classification of different plastic materials.
THz and mid IR spectroscopy of high-molecular PE (HMW) and ultra high-molecular PE (UHMW) reveals modifications of the molecular structure. Characteristic absorption bands are changed if the two materials are exposed by γ-Co60 radiation up to 600 kGy and subsequently stored at an annealing temperature of 398 K until for 729 days.
Laser-induced periodic surface structures (LIPSS, ripples) are a universal phenomenon that can be observed on almost any material after the irradiation by linearly polarized laser beams, particularly when using ultrashort laser pulses with durations in the picosecond to femtosecond range. During the past few years significantly increasing research activities have been reported in the field of LIPSS, since their generation in a single-step process provides a simple way of nanostructuring and surface functionalization towards the control of optical, mechanical or chemical properties. In this contribution current applications of LIPSS are reviewed, including the colorization of technical surfaces, the control of surface wetting, the tailoring of surface colonization by bacterial biofilms, and the improvement of the tribological performance of nanostructured metal surfaces.
We demonstrate narrow band spectral intensity switching in dual-core photonic crystal fibers made of highly nonlinear glass under femtosecond excitation. The fibers expressed dual-core asymmetry, thus the slow and fast fiber cores were unambiguously distinguished according to their dispersion profiles. The asymmetry effect on the dual-core Propagation in anomalous dispersion region was studied both experimentally and numerically. The experimental study was carried
out using femtosecond laser amplifier system providing tunable pulses in range of 1500 nm - 1800 nm. The obtained results unveiled, that it is possible to improve nonlinearly the coupling between the two waveguides by excitation of the fast fiber core. The results were obtained in regime of high-order soliton propagation and were verified numerically by the coupled generalized nonlinear Schrödinger equations model. The spectral analysis of the radiation transferred to the non-excited core revealed the role of effects such as third order dispersion, soliton compression and spectral dependence of the coupling efficiency. The simulation results provide reasonable agreement with the experimentally observed spectral evolutions in the both fiber cores. Under 1800 nm excitation, narrow band spectral intensity switching was registered with contrast of 23 dB at 10 mm fiber length by changing the excitation pulse energy in sub-nanojoule range.
Active thermography is a fast, contactless and non-destructive technique that can be used to detect internal defects in different types of material. Volumetric irregularities such as the presence of pores in materials produced by the Additive Manufacturing processes can strongly affect the thermophysical and the mechanical properties of the final component.
In this work, an experimental investigation aimed at detecting different pores in a sample made of stainless AISI 316L produced by Laser Powder Bed Fusion (L-PBF) was carried out using pulsed thermography in reflection mode. The capability of the technique and the adopted setups in terms of geometrical and thermal resolution, acquisition frequency and energy Density of the heating source were assessed to discern two contiguous pores as well as to detect a single pore. Moreover, a quantitative indication about the minimum resolvable pore size among the available and analysed defects was provided. A powerful tool to assess the Limits and the opportunities of the pulsed technique in terms of detectability and localizability was provided by comparing active thermography results to Computed Tomography as well as a related Finite Element Analysis (FEA) to simulate the pulsed heating transfer with Comsol.
The current paper presents residual stress analyses of large scale LTT (Low Transformation Temperature) welds. LTT filler materials are specially designed for residual stress engineering by means of an adjusted martensite phase transformation. Controlling the level of mostly detrimental residual stresses already during the welding process would be highly attractive as time and cost consuming post processing may be prevented. In large scale welds the residual stress state is influenced by the heat control (e.g. interpass temperature) during welding. Therefore, welding residual stresses are studied here putting the focus on the influence of welding process parameters while joining heavy steel sections with a thickness of 25 mm. The residual stress state was determined at the top surface using X-ray diffraction as well as in the bulk by neutron diffraction. The results show that control of the interpass temperature is vital for the residual stresses present in the joints. This accounts for the top surface but is most pronounced for the bulk of the welds. While high interpass temperatures are appropriate to induce compressive residual stresses in the weld metal, low interpass temperatures favor unwanted tensile residual stresses instead.