Additive Fertigung
Filtern
Dokumenttyp
- Zeitschriftenartikel (46)
- Beitrag zu einem Tagungsband (21)
- Forschungsbericht (3)
- Vortrag (2)
- Posterpräsentation (1)
- Forschungsdatensatz (1)
Schlagworte
- Additive manufacturing (11)
- Laser metal deposition (11)
- Additive Manufacturing (9)
- DED (9)
- Additive Fertigung (6)
- Directed Energy Deposition (5)
- Hochfester Stahl (5)
- Widerstandspunktschweißen (5)
- AM (4)
- Inconel 718 (4)
- Laser Metal Deposition (4)
- Laser beam welding (4)
- Liquid Metal Embrittlement (4)
- Mechanical properties (4)
- Porosity (4)
- Quality assurance (4)
- Artificial neural network (3)
- Directed energy deposition (3)
- Heat treatment (3)
- Künstliche Intelligenz (3)
- L-PBF (3)
- Microstructure (3)
- Resistance spot welding (3)
- WAAM (3)
- Crack (2)
- DED-EB (2)
- Data preparation (2)
- Dimensional accuracy (2)
- Directed Enery Deposition (2)
- Duplex AISI 2205 (2)
- EBAM (2)
- Elektronenstrahlschweißen (2)
- FGM (2)
- Flüssigmetallinduzierte Rissbildung (2)
- Hybrid components (2)
- Laser Welding (2)
- Laser welding (2)
- Liquid metal embrittlement (2)
- Neuronales Netz (2)
- Nickel (2)
- PBF-LB/M (2)
- Path planning (2)
- Process monitoring (2)
- Refill friction stir spot welding (2)
- Schweißnahtbewertung (2)
- Selective Laser Melting (2)
- Simulation (2)
- Stainless Steel (2)
- Submerged arc welding (2)
- Ti-6Al-4V (2)
- Welding simulation (2)
- Wire electron beam additive manufacturing (2)
- Zink (2)
- 316L (1)
- AGIL (1)
- AHSS (1)
- AM feature integration (1)
- Advanced High-Strength Steel (AHSS) (1)
- Advanced high strength steels (1)
- Advanced high-strength steel (1)
- Al-Mg-Si (1)
- Al-Mg-Si-Legierungen (1)
- AlMg0.7SiTiB filler wire (1)
- Aluminum bronze (1)
- Analytical model (1)
- Artificial intelligence (1)
- Auftragschweißen (1)
- Automobilindustrie (1)
- Automotive (1)
- Bead-on-plate welds (1)
- Bending test (1)
- Build direction (1)
- Build-up Orientation (1)
- Build-up strategy (1)
- Calculation time (1)
- Cimensional Accuracy (1)
- Clad steels (1)
- Condition monitoring (1)
- Convolutional neural network (1)
- Crater (1)
- Critical strain (1)
- CuSn1 (1)
- DED-LB (1)
- DIC (1)
- Damage prediction (1)
- Density measurement (1)
- Deposition rate (1)
- Design of experiments (1)
- Digital Image Correlation (1)
- Digitalization (1)
- Direct energy deposition (1)
- Dissimilar joints (1)
- Distortion (1)
- Distortion simulation (1)
- EBSD (1)
- Edge effects (1)
- Edge quality (1)
- Efficient modelling (1)
- Eindringprüfung (1)
- Electromagnetic support (1)
- Electron beam (1)
- Electron beam welding (1)
- Embedded electronics (1)
- Energy parameters of the arc (1)
- Ermüdung (1)
- FEM (1)
- Finite Element Method (1)
- Finite element simulation (1)
- Flange width (1)
- Flüssigmetallversprödung (1)
- Functionally Graded Materials (1)
- Funktionally Graded Material (1)
- Fügequalität (1)
- Galvanized steel (1)
- Gap bridgeability (1)
- Gleeble (1)
- Grain refinement (1)
- Hardness (1)
- Heat Input (1)
- Heat Treatment (1)
- Heat flow (1)
- Heat treatments (1)
- Heißzug (1)
- High speed laser cladding (1)
- High-Power Welding (1)
- High-strength fine-grained steels (1)
- Hot Cracks (1)
- Hybrid Laser-Arc Welding (1)
- Hybrid Part (1)
- Hybrid laser arc welding (1)
- Hybrid laser-arc welding (1)
- Inconel 625 (1)
- Inconel 939 (1)
- Industrial and Manufacturing Engineering (1)
- Integrated alignment features (1)
- KI (1)
- Körperschall (1)
- Künstliche Neuronale Netze (1)
- LMD (1)
- LPA (1)
- LW (1)
- Laser (1)
- Laser Beam Welding (1)
- Laser Metal Deposition (LMD) (1)
- Laser Powder Bed Fusion (1)
- Laser cutting (1)
- Laser powder bed fusion (1)
- Laser powder-based directed energy deposition (1)
- Laser surfacing (1)
- Laser-Pulver-Auftragschweißen (1)
- Laser-Pulver-Auftragschweißen (LPA) (1)
- Laser-metal-deposition (1)
- Laserpulverauftragschweißen (1)
- Liquation Cracking (1)
- Liquid Metal Embrittlement (LME) (1)
- Magnesium Alloy (1)
- Magnesium alloy (1)
- Maritime Components (1)
- Mechanical properties of the joints (1)
- Mechanisch technologische Kennwerte (1)
- Melt pool dinamics (1)
- Multi-materials joining (1)
- Nickel-based superalloy (1)
- Numerical Simulation (1)
- Numerical simulation (1)
- Numerical simulations (1)
- Open science (1)
- Open source (1)
- Optical flow (1)
- Optische Emissionsspektroskopie (OES) (1)
- PBF/LB-M (1)
- Pearlitic microstructure (1)
- Pipe Welding (1)
- Pipe weld preparation (1)
- Plasma cutting (1)
- Plastic deformation (1)
- Porosität (1)
- Powder Analysis (1)
- Pre-weld Preparation (1)
- Precipitation hardening aluminum alloys (1)
- Preheatin (1)
- Process chain (1)
- Prozessüberwachung (1)
- Prüfverfahren (1)
- Quality monitoring (1)
- Qualität (1)
- Rail tracks (1)
- Recycling (1)
- Research data management (1)
- Resistance Spot Welding (RSW) (1)
- SLM (1)
- Schallemissionsanalyse (SEA) (1)
- Schutzgas (1)
- Schweißsimulation (1)
- Schweißstruktursimulation (1)
- Seam geometry (1)
- Selektive-laser-melting (1)
- Shipbuilding steel (1)
- Solidification behaviour (1)
- Solidification cracking (1)
- Stainless steels (1)
- Strain fields prediction (1)
- Strain measurement (1)
- Superalloy (1)
- TIG welding (1)
- Temperature behavior (1)
- Temperature distribution (1)
- Tensile performance (1)
- Tensile properties (1)
- Tensile resistance spot welding experiment (1)
- Texture (1)
- Thermographie (1)
- Thick-Walled Steel (1)
- Thick-walled steel (1)
- Titanium alloy (1)
- Turbine components (1)
- Two-run welding technique (1)
- Unterpulverschweißen (1)
- Verzug (1)
- WEBAM (1)
- Welding (1)
- Welding Current (1)
- Welding Simulation (1)
- Welding parameter (1)
- Weldx (1)
- Widerstandpunktschweißen (1)
- Wire Electron Beam Additive Manufacturing (1)
- Wire arc additive manufacturing (1)
- Wire-based additive manufacturing (1)
- Wärmenachbehandlung (1)
- Zinkbeschichtung (1)
Organisationseinheit der BAM
- 9 Komponentensicherheit (73)
- 9.3 Schweißtechnische Fertigungsverfahren (70)
- 9.6 Additive Fertigung metallischer Komponenten (3)
- 1 Analytische Chemie; Referenzmaterialien (1)
- 1.9 Chemische und optische Sensorik (1)
- 5 Werkstofftechnik (1)
- 5.2 Metallische Hochtemperaturwerkstoffe (1)
- 7 Bauwerkssicherheit (1)
- 7.7 Modellierung und Simulation (1)
- 8 Zerstörungsfreie Prüfung (1)
Eingeladener Vortrag
- nein (2)
In additive manufacturing (AM) directed energy deposition (DED), parts are built by welding layers of powder or wire feedstock onto a substrate with applications for steel powders in the fields of forging tools, spare parts, and structural components for various industries. For large and bulky parts, the choice of toolpaths influences the build rate, the mechanical performance, and the distortions in a highly geometry-dependent manner. With weld-path lengths in the range of hundreds of meters, a reliable, automated tool-path generation is essential for the usability of DED processes. This contribution presents automated tool-path generation approaches and discusses the results for arbitrary geometries. Socalled “zig-zag” and “contour-parallel” processing strategies are investigated and the tool-paths are automatically formatted into machine-readable g-code for experimental validation to build sample geometries. The results are discussed in regard to volume-fill, microstructure, and porosity in dependence of the path planning according to photographs and metallographic cross-sections.
Components distort during directed energy deposition (DED) additive manufacturing (AM) due to the repeated localised heating. Changing the geometry in such a way that distortion causes it to assume the desired shape – a technique called distortion-compensation – is a promising method to reach geometrically accurate parts. Transient numerical simulation can be used to generate the compensated geometries and severely reduce the amount of necessary experimental trials. This publication demonstrates the simulation-based generation of a distortioncompensated DED build for an industrial-scale component. A transient thermo-mechanical approach is extended for large parts and the accuracy is demonstrated against 3d-scans. The calculated distortions are inverted to derive the compensated geometry and the distortions after a single compensation iteration are reduced by over 65%.
Due to rapid, localized heating and cooling, distortions accumulate in additive manufactured laser metal deposition (LMD) components, leading to a loss of dimensional accuracy or even cracking. Numerical welding simulations allow the prediction of these deviations and their optimization before conducting experiments. To assess the viability of the simulation tool for the use in a predictive manner, comprehensive systems as well as to choose the optimal product matches, product analysis methods are needed. Indeed, most of the known methods aim to analyze a product or one product family on the physical level. Different product families, however, may differ largely in terms of the number and nature of components. This fact impedes an efficient comparison and choice of appropriate product family combinations for the production system. A new methodology is proposed to analyze existing products in view of their functional and physical architecture. The aim is to Cluster these products in new assembly oriented product families for the optimization.
In additive manufacturing (AM) Laser Metal Deposition (LMD), parts are built by welding layers of powder feedstock onto a substrate. Applications for steel powders include forging tools and structural components for various industries. For large parts, the choice of tool-paths influences the build-rate, the part performance and the distortions in a highly geometry-dependent manner. With weld-path lengths in the range of hundreds of meters, a reliable, automated tool path generation is essential for the usability of LMD processes.
In this contribution, automated tool-path generation approaches are shown and their results are discussed for arbitrary geometries. The investigated path strategies are the classical approaches: “Zig-zag-” and “contour-parallel-strategies”. After generation, the tool-paths are automatically formatted into g-code for experimental build-up and ASCII for a numerical simulation model. Finally, the tool paths are discussed in regards to volume-fill, microstructure and porosity for the experimental samples.
This work presents a part of the IGF project 18737N “Welding distortion simulation” (FOSTA P1140)
The laser-based direct energy deposition (DED) as a technology for additive manufacturing allows the production of near net shape components. Industrial applications require a stable process to ensure reproducible quality. Instabilities in the manufacturing process can lead to faulty components which do not meet the required properties.
The DED process is adjusted by various parameters such as laser power, velocity, powder mass flow and spot diameter, which interact with each other. A frequently used comparative parameter in welding is the energy per unit length and is calculated from the laser power and the velocity in laser welding. The powder per unit length comparative parameter in the DED process has also be taken into account, because this filler material absorbs energy in addition to the base material.
This paper deals with the influence of mass energy as a comparative parameter for determining the properties of additively manufactured parts. The same energy per unit length of 60 J/mm as well as the same powder per unit length of 7.2 mg/mm can be adjusted with different parameter sets. The energy per unit length and the powder per unit length determine the mass energy. The laser power is varied within the experiments between 400 W and 900 W. Energy per unit length and powder per unit length are kept constant by adjusting velocity and powder mass flow. Using the example of Inconel 718, experiments are carried out with the determined parameter sets. In a first step, individual tracks are produced and analyzed by means of micro section. The geometry of the tracks shows differences in height and width. In addition, the increasing laser power leads to a higher dilution of the base material. To determine the suitability of the parameters for additive manufacturing use, the individual tracks are used to build up parts with a square base area of 20x20 mm². An investigation by Archimedean principle shows a higher porosity with lower laser power. By further analysis of the micro sections, it can be seen that at low laser power, connection errors occur between the tracks.
The results show that laser power, velocity and powder mass flow have to be considered in particular, because a constant mass energy can lead to different geometric as well as microscopic properties.
Rapid localized heating and cooling during additive manufacturing using laser deposition method (LMD) lead to loss of dimensional accuracy as well as cracking of built parts. Finite-Element welding simulations allow prediction of geometrical deviations and accumulated residual stresses as well as their optimization before conducting experiments. Due to the great length of stacked welds, calculation times for fully transient thermomechanical simulations are currently long, the calculation stability suffers from the high number of contact bodies in the model and the modelling effort is high, as the geometries need to be sliced and positioned layer-wise.
In this contribution, an integrated modelling approach is demonstrated for a thin-walled LMD component made from 30 layers of 1.4404 (316L) stainless steel: Instead of the layer-by-layer modelling strategy commonly found in the literature, the whole component mesh is kept in one piece and the fully transient, layer-by-layer material deposition is implemented via element sets. In contrast to prior simulations, nonlinear contact between the layers does not have to be considered, significantly decreasing calculation times. The calculated distortions are compared to recently published, in-situ digital image correlation (DIC) measurements as well as numerical simulations conducted with the established layer-wise modelling strategy to judge result quality. Finally, the improvement in calculation time and ease-of-use is compared between both modelling approaches and conclusions regarding future usage for industrial-scale components are drawn.
Additive manufacturing is no longer just used for the production of prototypes but already found its way into the industrial production. However, the fabrication of massive metallic parts with high geometrical complexity is still too time-consuming to be economically viable. The combination of the powder bed-based selective laser melting process (SLM), known for its geometrical freedom and accuracy, and the nozzle-based laser metal deposition process (LMD), known for its high build-up rates, has great potential to reduce the process duration. For the industrial application of the SLM-LMD hybrid process chain it is necessary to investigate the interaction of the processes and its effect on the material properties to guarantee part quality and prevent component failure. Therefore, hybrid components are manufactured and examined before and after the heat treatment regarding the microstructure and the hardness in the SLM-LMD transition zone. The experiments are conducted using the nickel-based alloy Inconel 718.
The paper deals with the integration of a light emitting diode (LED) into an additive manufactured metal component. Selective laser melting (SLM) and laser metal deposition (LMD) are used. The material used is the chrome-nickel steel 316L. The basic component is manufactured by means of SLM and consists of a solid body and an area with grid structure. The solid body includes a duct in the shape of a groove with a recess for the positioning of the power cable. The LED is embedded in the grid structure via an inlet from the solid body. In further processing, the groove is filled with LMD. Two strategies with different parameter combinations were investigated. It shows that a high energy input near the power cable leads to its destruction. By using multiple parameter combinations during the manufacturing process, this destruction can be prevented. There was a comparison of both strategies with regard to the necessary number of tracks and duration of welding time.
Pores in additive manufactured metal parts occur due to different reasons and affect the part Quality negatively. Few investigations on the origins of porosity are available, especially for Ni-based super alloys. This paper presents a new study to examine the influence of common processing Parameters on the Formation of pores in parts built by laser metal Deposition using Inconel 718 powder. Further, a comparison between the computed tomography (CT) and the Archimedes method was made. The Investigation Shows that CT is able to identify different kinds of pores and to give further Information about their distribution. The identification of some pores as well as their shape can be dependent on the Parameter Setting of the Analysis tool. Due to limited measurement Resolution, CT is not able to identify correctly pores with Diameters smaller than 0.1 mm, which leads to a false decrease on Overall porosity. The applied Archimedes method is unable to differentiate between gas porosity and other Kinds of holes like internal cracks or lack of Fusion, but it delivered a proper value for Overall porosity. The method was able to provide suitable data for the statistical Evaluation with design of Experiments, which revealed significant Parameters ont he Formation of pores in LMD.
Build-up strategies for temperature control using laser metal deposition for additive manufacturing
(2018)
The track geometry created with laser metal deposition (LMD) is influenced by various parameters. In this case, the laser power has an influence on the width of the track because of an increasing energy input. A larger melt pool is caused by a rising temperature. In the case of a longer welding process, there is also a rise in temperature, resulting in a change of the track geometry. This paper deals with the temperature profiles of different zigzag strategies and spiral strategies for additive manufacturing. A two-color pyrometer is used for temperature measurement on the component surface near the melt pool. Thermocouples measure the temperatures in deeper regions of a component. The welds are located in the center and in the edge area on a test part to investigate the temperature evolution under different boundary conditions. The experiments are carried out on substrates made from mild steel 1.0038 and with the filler material 316L. The investigations show an influence on the temperature evolution by the travel path strategy as well as the position on the part. This shows the necessity for the development and selection of build-up strategies for different part geometries in additive manufacturing by LMD.
Laser metal deposition (LMD) is an established technology for two-dimensional surface coatings. It offers high deposition rates, high material flexibility, and the possibility to deposit material on existing components. Due to these features, LMD has been increasingly applied for additive manufacturing of 3D structures in recent years. Compared to previous coating applications, additive manufacturing of 3D structures leads to new challenges regarding LMD process knowledge. In this paper, the process steps for LMD as additive manufacturing technology are described. The experiments are conducted using titanium alloy Ti-6Al-4Vand Inconel 718. Only the LMD nozzle is used to create a shielding gas atmosphere. This ensures the high geometric flexibility needed for additive manufacturing, although issues with the restricted size and quality of the shielding gas atmosphere arise. In the first step, the influence of process parameters on the geometric dimensions of single weld beads is analyzed based on design of experiments. In the second step, a 3D build-up strategy for cylindrical specimen with high dimensional accuracy is described. Process parameters, travel paths, and cooling periods between layers are adjusted. Tensile tests show that mechanical properties in the as-deposited condition are close to wrought material. As practical example, the fir-tree root profile of a turbine blade is manufactured. The feasibility of LMD as additive technology is evaluated based on this component.
Laser Metal Deposition (LMD) as a technology for additive manufacturing allows the production of large components outside of closed working chambers. Industrial applications require a stable process as well as a constant deposition of the filler material in order to ensure uniform volume growth and reproducible mechanical properties. This paper deals with the influence of travel path strategies on temperature profile and material deposition. Meandering and spiral hatching strategies are used in the center as well as in the edge of a specimen. The temperature is measured with thermocouples attatched to the backside of the specimen. The tests are carried out on the materials S235JR and 316L. The results show a strong dependence of the maximum temperatures on the travel path strategy and the welding position on the component.
Laser metal deposition (LMD) has been applied as a coating technology for many years. Today, the technologies capacity to produce 3D depositions leads to a new field of application as additive manufacturing method. In this paper, 3D laser metal deposition of titanium alloy Ti-6Al-4V is studied with special regard to the demands of additive manufacturing. Therefore, only the coaxial LMD powder nozzle is used to create the shielding gas atmosphere, which ensures high geometric flexibility. Furthermore, specimen with high aspect ratio and hundreds of layers are manufactured, which represent typical features in additive manufacturing. The presented study contains the following steps: First, cylindrical specimens are manufactured with a standard shell-core build-up strategy and mechanical properties as well as fracture mechanisms are determined. Based on the results, experiments are conducted to improve the build-up strategy and new tensile test specimens are built with the improved strategy. The improved strategy incorporates variable track overlap ratios to achieve a constant growth in the shell and core area. As blanks, lean cylinders comprising more than 240 layers and a height of more than 120mm are manufactured. The specimens are analyzed by X-ray inspection for material defects. Fractured surfaces are observed via scanning electron microscopy and the composition of the surfaces is determined using energy dispersive X-ray spectroscopy. The tensile test results prove mechanical properties close to ASTM F1108 specification for wrought material.
Distortions in Additive Manufacturing (AM) Laser Metal Deposition (LMD) occur in the newly-built component due to rapid heating and solidification and can lead to shape deviations and cracking. This paper presents a novel approach to quantify the distortions experimentally and to use the results in numerical simulation validation. Digital Image Correlation (DIC) is applied together with optical filters to measure in-situ distortions directly on a wall geometry produced with LMD. The wall shows cyclic Expansion and shrinking with the edges bending inward and the top of the sample exhibiting a slight u-shape as residual distortions. Subsequently, a structural Finite Element Analysis (FEA) of the experiment is established, calibrated against experimental temperature profiles and used to predict the in-situ distortions of the sample. A comparison of the experimental and numerical results reveals a good agreement in length direction of the sample and quantitative deviations in height direction, which are attributed to the material model used. The suitability of the novel experimental approach for measurements on an AM sample is shown and the potential for the validated numerical model as a predictive tool to reduce trial-and-error and improve part quality is evaluated.