Filtern
Dokumenttyp
Schlagworte
- Amorphous carbon (1)
- Arc discharge (1)
- Carbon nitride films (1)
- Cathodic arc discharge (1)
- Dielectric properties (1)
- Expanded Graphite (1)
- Functionalization (1)
- Gas Discharge Plasma (1)
- Gas permeation (1)
- Graphit (1)
Eingeladener Vortrag
- nein (1)
Single-walled carbon nanotubes (SWNT) and carbon nitride films are synthesized by a direct current (dc) arc discharge at slightly reduced pressure and by an inductively coupled r.f. plasma (ICP) at atmospheric pressure, respectively. By treatment with nitric acid SWNT are purified from by-products and characterized by scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM), and Raman spectroscopy. ICP allows the deposition of carbon nitride films on steel substrate. The deposition of the films creates a relatively strong radial symmetric profile. The structure of the films are rather independent of the distance between substrate and plasma. Raman, Fourier transform infrared (FTIR), and energy dispersive X-ray (EDX) spectroscopy are used for analyzing the carbon nitride materials.
Single walled carbon nanotubes (SWNT) have been produced in an electric arc discharge by using a graphite rod as anode which is filled with a powder mixture of graphite and metallic catalysts like nickel and yttrium. The soot material containing approximately a third of SWNT was collected from the cathode region as a soft, voluminous material. The main by-products in this process are amorphous carbon and graphitic nanoparticles which have to be removed by an appropriate purification process. The as-produced soot material was purified by gas phase oxidation in air at 355 °C. The oxidation of amorphous carbon in air is advantageous against wet chemical methods because it is better controllable. Thermogravimetric analysis and electron microscopy were used to investigate the oxidation behavior of the different kinds of carbon. Oxidation of SWNT and amorphous carbon occurs simultaneously even at moderate temperatures, whereas amorphous carbon is more rapidly oxidized than SWNT. For optimizing the purification procedure by gas phase oxidation, kinetic studies were used to determine the oxidation time for each component in the soot at a given temperature. So it is possible to remove the amorphous carbon quantitatively with minimal losses of SWNT. But it was found that graphitic nanoparticles have the highest stability against oxidation and could therefore not be quantitatively removed by this method without the complete destruction of SWNT. Therefore, the electric arc discharge process has to be a controlled process for minimum production of graphitic nanoparticles to obtain a material with a high content of SWNT.
Effects of Heat Treatment on the Structure of Thermal Plasma Synthesized SiCN Composite Nanopowders
(2003)
Effects of Heat Treatment on the Structure of Thermal Plasma Synthesized SiCN Composite Nanopowders
(2003)
SiCN composite nanopowders with different chemical composition and characteristics were synthesized by the RF induction plasma at atmospheric pressure. Frequently the as-produced powders exhibit a high degree of chemical disorder or structural defects. Because the composition and the microstructure of starting powders have a great influence on the properties of composite ceramics, the changes of chemical composition, crystallization, and morphology of the as-produced powders during heat treatment up to 1500 °C were investigated in detail.
We have developed a very fast and entirely gas-phase based purification technique for carbon nanotubes (CNT) that allows removing metal and metal oxide impurities with high effectiveness. CNT agglomerates from chemical vapor deposition (CVD) synthesis which contained carbon encapsulated catalysts were injected into an atmospheric plasma torch. Very high heating rates allow for quasi-instantaneous vaporization of catalyst particles. This way, metal vapors are hyposized to break mechanically instable encapsulations and effuse from incomplete ones faster than thermally induced graphitization stabilizes such particle encapsulations. The ash content of multi-walled (MW) CNT samples was reduced to less than 15% of the initial value within a few milliseconds. Also the metal content of single-walled (SW) CNT agglomerates was significantly reduced. Repeated injection of CNT agglomerates into the plasma torch resulted in higher-purity products of improved structural integrity and increased oxidation resistance.
Herstellung und Modifizierung von Nano- und Mikropulvern im thermischen und nichtthermischen Plasma
(2007)
Plasma-chemical bromination has been shown to be well-suited for highly selective and efficient C–Br-functionalization of polyolefin surfaces and has now been applied to graphitic materials, including highly oriented pyrolytic graphite (HOPG), natural graphite, carbon nanotubes, and graphitized carbon fibres. In contrast to the radical substitution of hydrogen by bromine at hydrogen-terminated sp3-hybridized carbon, bromination of all-carbon bound sp2-hybridized carbon in graphene requires addition to aromatic double bonds. The related change of sp2 to sp3 hybridization of the carbon atoms involved helps to explain experimental results of a loss in surface planarity on brominated HOPG. Bromine concentrations of up to 50 bromine atoms per 100 C-atoms were achieved in elemental bromine vapour under low-pressure plasma conditions using low-energetic inductively coupled radio-frequency plasma excitation. The time scale of the bromination progress was found to increase with the specific surface area of the material. The results of plasma-chemical bromination are compared to that of wet-chemical electrophilic addition reactions, which achieved 28 Br per 100 C for MWCNT. The resulting C–Br bonds from plasma-chemical processing of graphitic materials were shown to be well-suited for hydroxyl functionalization and for grafting of organic molecules by nucleophilic substitution with 1,6-diaminohexane and (3-aminopropyl)triethoxysilane.