Filtern
Dokumenttyp
Schlagworte
- Deponieabdichtung (3)
- Organische Schadstoffe (3)
- Heavy metals (2)
- Kombinationsdichtung (2)
- Leaching (2)
- Mineralische Dichtung (2)
- XPS (2)
- Abfallmaterialien (1)
- Auslaugungsverfahren (1)
- Building Material (1)
Organisationseinheit der BAM
We report the results of a Versailles Project on Advanced Materials and Standards (VAMAS) interlaboratory study on the measurement of the shell thickness and chemistry of nanoparticle coatings. Peptide-coated gold particles were supplied to laboratories in two forms: a colloidal suspension in pure water and particles dried onto a silicon wafer. Participants prepared and analyzed these samples using either X-ray photoelectron spectroscopy (XPS) or low energy ion scattering (LEIS). Careful data analysis revealed some significant sources of discrepancy, particularly for XPS. Degradation during transportation, storage, or sample preparation resulted in a variability in thickness of 53%. The calculation method chosen by XPS participants contributed a variability of 67%. However, variability of 12% was achieved for the samples deposited using a single method and by choosing photoelectron peaks that were not adversely affected by instrumental transmission effects. The study identified a need for more consistency in instrumental transmission functions and relative sensitivity factors since this contributed a variability of 33%. The results from the LEIS participants were more consistent, with variability of less than 10% in thickness, and this is mostly due to a common method of data analysis. The calculation was performed using a model developed for uniform, flat films, and some participants employed a correction factor to account for the sample geometry, which appears warranted based upon a simulation of LEIS data from one of the participants and comparison to the XPS results.
The environmental impact assessment of materials is usually based on laboratory tests, mostly in combination with models describing the longterm fate of the substances of interest in the targeted environmental compartment. Thus, laboratory tests are the fundamental link to achieve appropriate assessment conclusions which makes it essential to generate consistent results. This just as applies to the leaching of cementitious materials. In Europe, the leaching behavior of monolithic building materials is tested in the Dynamic Surface Leaching Test following the specification CEN/TS 16637–2. An interlaboratory comparison on European level regarding this technical specification showed relatively high intra- and interlaboratory variations for the tested materials (monolithic copper slag and cement stabilized coal fly ash). Therefore the German Committee for Structural Concrete (DAfStb) framed a guideline to specify additional testing conditions for cementitious materials. To assess the possible improvement by this guidelines measures, a round robin test with 11 participants from Germany and the Netherlands was conducted. This work aims to provide insight into the factors to be considered in the testing of alkaline materials, including sample preparation, and highlights crucial procedures and their manifestation in the results. All evaluated parameters showed improved results compared to the earlier round robin test. The relative standard deviations for repeatability (RSDr) and reproducibility (RSDR) of the elements calcium, barium, antimony, chromium, molybdenum and vanadium, which are the parameters evaluated in both round robin tests, were RSDr = 4%, 4%, 2%, 5%, 5%, and 5% respectively (4% in average) for this work, in comparison to the European round robin test with an average RSDr of 29% (17%, 17%, 20%, 40%, 36%, and 42%). The RSDR improved from 41% (30%, 36%, 29%, 57%, 40%, and 56%) to 14% (12%, 8%, 6%, 28%, 15%, and 12%). CO2 ingress during testing and the inaccuracy of eluate analytics for concentrations close to the determination limits were identified as the main sources of error.
Accurate and reproducible measurement of the structure and properties of high-value nanoparticles is extremely important for their commercialization. A significant proportion of engineered nanoparticle systems consist of some form of nominally core-shell structure, whether by design or unintentionally. Often, these do not form an ideal core-shell structure, with typical deviations including polydispersity of the core or shell, uneven or incomplete shells, noncentral cores, and others. Such systems may be created with or without intent, and in either case an understanding of the conditions for formation of such particles is desirable. Precise determination of the structure, composition, size, and shell thickness of such particles can prove challenging without the use of a suitable range of characterization techniques. Here, the authors present two such polymer core-shell nanoparticle systems, consisting of polytetrafluoroethylene cores coated with a range of thicknesses of either polymethylmethacrylate or polystyrene. By consideration of surface energy, it is shown that these particles are expected to possess distinctly differing coating structures, with the polystyrene coating being incomplete. A comprehensive characterization of these systems is demonstrated, using a selection of complementary techniques including scanning electron microscopy, scanning transmission electron microscopy, thermogravimetric analysis, dynamic light scattering, differential centrifugal sedimentation, and X-ray photoelectron spectroscopy. By combining the results provided by these techniques, it is possible to achieve superior characterization and understanding of the particle structure than could be obtained by considering results separately.
Kunststoff- und Kunststoffrasenflächen kommt bei intensiv genutzten Flächen als Allwetterbeläge eine große Bedeutung zu. Sie leisten einen wichtigen Beitrag zur Absicherung eines ganzjähriger Sportangebote.
Gerade Kunststoffrasen ist aber in den letzten Jahren häufig in die Kritik geraten, insbesondere durch gefährliche Inhaltsstoffe und andere negative Einflüsse auf die Umwelt. Dies hat bei Bauherren zu einer Verunsicherung geführt und Fragen aufgeworfen, die erst teilweise beantwortet sind. Die Diskussionen rund um diesen Allwetterbelag haben bereits dazu geführt, dass von Seiten der Industrie viel verändert wurde und neue innovative Lösungen gefunden werden.
Der Fachbericht stellt eine Handreichung für Fachleute und interessierte Laien dar, um mehr Klarheit besonders hinsichtlich der Umweltanforderungen zu erzielen.
Column percolation tests may be suitable for prediction of chemical leaching from soil and soil materials. However, compared with batch leaching tests, they are time-consuming. It is therefore important to investigate ways to shorten the tests without affecting the quality of results. In this study, we evaluate the feasibility of decreasing testing time by increasing flow rate and decreasing equilibration time compared to the conditions specified in ISO/TS 21268-3, with equilibration periods of 48 h and flow rate of 12 mL/h. We tested three equilibration periods (0, 12–16, and 48 h) and two flow rates (12 and 36 mL/h)on four different soils and compared the inorganic constituent releases. For soils A and D, we observed similar values for all conditions except for the 0 h–36 mL/h case. For soil B, we observed no appreciable differences between the tested conditions, while for soil C there were no consistent trends probably due to the difference in ongoing oxidation reactions between soil samples. These results suggest that column percolation tests can be shortened from 20 to 30 days to 7–9 days by decreasing the equilibration time to 12–16 h and increasing the flow rate to 36 mL/h for inorganic substances.
A simple batch test leaching procedure is used in many countries, as a compliance test, to evaluate the leaching of mainly inorganic substances from soil. However, agitating certain types of soil and then passing the solution through a membrane filter with 0.45-µm pores yields filtrates that have been colored by the colloidal particles. These colloids might affect the results of the inorganic substances obtained in the batch tests. In this study, we evaluated the effects of colloidal particles on the results and the reproducibility of batch tests on contaminated soil using different agitation methods and membrane filters with different pore sizes. The leaching behaviors of As, Pb, Se, F and Cl from three types of soil were studied. The As and Pb concentrations in the leachates of some types of soil were clearly affected by the amount of colloidal particles with a diameter of 0.10–0.45 µm and by the agitation method used. This was probably because As and Pb were present mainly in the particulate form in the leachate that had been passed through a membrane filter with 0.45-µm pores. This is not the case for every type of soil. The results of batch leaching tests showed that not only dissolved but also colloidal forms with a diameter of 0.10–0.45 µm might be included and that the existence of colloidal particles in the leachate decreases the batch leaching test reproducibility.