Filtern
Dokumenttyp
- Zeitschriftenartikel (7)
- Beitrag zu einem Tagungsband (2)
- Vortrag (1)
Schlagworte
- DFG SPP 2005 (3)
- Characterization (2)
- Portland cement (2)
- Additive Manufacturing (1)
- Analyse (1)
- Bewertung (1)
- Calcined clay (1)
- Cement (1)
- Chemistry (1)
- Condensed Matter Physics (1)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (1)
The CuII complex of H4TETP (H4TETP = 1,4,8,11-tetraazatetradecane-1,4,8,11-tetrapropionic acid) is five-coordinate with a distorted square-pyramidal structure (τ = 0.45; i.e. the geometry is nearly half-way between square-pyramidal and trigonal-bipyramidal) and a relatively long Cu–N and a short Cu–O bond; the comparison between powder and solution electronic spectroscopy, the frozen solution EPR spectrum and ligand-field-based calculations (angular overlap model, AOM) indicate that the solution and solid state structures are very similar, i.e. the complex has a relatively low 'in-plane' and a significant axial ligand field with a dx²-y² ground state. The ligand-enforced structure is therefore shown to lead to a partially quenched Jahn–Teller distortion and to a relatively low complex stability, lower than with the corresponding acetate-derived ligand H4TETA. This is confirmed by potentiometric titration and by the biodistribution with 64Cu-labeled ligands which show that the uptake in the liver is significantly increased with the H4TETP-based system.
A thorough characterization of base materials is the prereq- uisite for further research. In this paper, the characterization data of the reference materials (CEM I 42.5 R, limestone pow- der, calcined clay and a mixture of these three components) used in the second funding phase of the priority program 2005 of the German Research Foundation (DFG SPP 2005) are presented under the aspects of chemical and min- eralogical composition as well as physical and chemical properties. The data were collected based on tests performed by up to eleven research groups involved in this cooperative program.
Two types of cements were selected as the reference cement in the priority program 2005 of the German Research Foundation (DFG SPP 2005). A thorough characterization of CEM I 42.5 R has been made in a recent publication. In this paper, the characterization data of the other reference cement CEM III/A 42.5 N are presented from the aspects of chemical and mineralogical compositions as well as physical and chemical properties. The characterization data of the slag, which is the second main constituent of this specific cement besides the clinker, are presented independently. For all data received, the mean values and the corresponding errors were calculated. The data shall be used for the ongoing research within the priority program. Also, researchers from outside this priority program can benefit from these data if the same materials are used.
Tomographie 3D-Radiometry for the Visualisation and Measurement of the Defects of Girth Seams
(2006)
A thorough characterization of starting materials is the precondition for further research, especially for cement, which contains various phases and presents quite a complex material for fundamental scientific investigation. In the paper at hand, the characterization data of the reference cement CEM I 42.5 R used within the priority program 2005 of the German Research Foundation (DFG SPP 2005) are presented from the aspects of chemical and mineralogical compositions as well as physical and chemical properties. The data were collected based on tests conducted by nine research groups involved in this cooperative program. For all data received, the mean values and the corresponding errors were calculated. The results shall be used for the ongoing research within the priority program.
A range of heat treatments have been developed for wrought Inconel 718 to obtain desired properties. For additively manufactured Inconel 718, the recently developed standard ASTM F3301 provides guidance for heat treatment of powder bed fusion specimens. Although this standard is based on standards developed for wrought Inconel 718, it does not include direct aging. Since direct aging reduces the number of processing steps, it can result in a post processing cost reduction if the desired properties are obtained. In this study, we characterized the microstructure and tensile behavior of Inconel 718 specimens produced by a laser powder bed fusion process. The specimens were heat treated according to two different routines after stress relieving: a full heat Treatment versus a one-step direct aging process. Differences in the resulting texture and grain morphology were observed.
The ex-situ stress-strain behavior was broadly similar. However, a slight increase in yield strength was observed for the direct aged specimen. In order to understand this behavior, investigations with in-situ synchrotron Energy dispersive X-ray diffraction tensile testing revealed differences in the load partitioning among different Crystal directions. Importantly, the elastic anisotropy expressed by the magnitude of the diffraction elastic constants showed a dependency on the microstructures.
High energy X-ray synchrotron diffraction is used to investigate the elastic anisotropy of the nickel-based superalloy IN718 produced by laser powder bed fusion (PBF-LB). This material is characterized by a columnar grain morphology with some crystallographic texture. The material is subjected to elastic loading to determine the diffraction elastic constants (DECs). Furthermore, the single-crystal elastic constants (SCEC) are refined from these experiments using different micromechanical models. The results show that each micromechanical model predicts a specific set of SCEC that well describes the elastic anisotropy of PBF-LB/IN718.