Filtern
Erscheinungsjahr
Dokumenttyp
- Vortrag (31)
- Beitrag zu einem Tagungsband (13)
- Zeitschriftenartikel (9)
- Beitrag zu einem Sammelband (9)
- Forschungsbericht (4)
- Posterpräsentation (2)
Sprache
- Englisch (68) (entfernen)
Schlagworte
- Safety (9)
- H2Safety@BAM (7)
- Explosion (5)
- Hydrogen (5)
- Acetylene (4)
- Explosion limits (3)
- Fire (3)
- Heat transfer (3)
- Wasserstoff (3)
- Deflagration (2)
Organisationseinheit der BAM
- 2 Prozess- und Anlagensicherheit (13)
- 2.1 Sicherheit von Energieträgern (13)
- 3 Gefahrgutumschließungen; Energiespeicher (4)
- 3.5 Sicherheit von Gasspeichern (4)
- 1 Analytische Chemie; Referenzmaterialien (1)
- 1.4 Prozessanalytik (1)
- 2.3 Einstufung von Gefahrstoffen und -gütern (1)
- 3.0 Abteilungsleitung und andere (1)
- 5 Werkstofftechnik (1)
- 5.3 Polymere Verbundwerkstoffe (1)
Eingeladener Vortrag
- nein (31)
Fire exposure tests of acetylene cylinders were performed. The purpose of the experiments was to gather information on the behavior in fire of such vessels, depending on the initial charge of acetylene. In fact "empty" acetylene cylinders still contain the solvent in which acetylene is dissolved plus the amount of acetylene to saturation at atmospheric pressure and ambient temperature and may still constitute a threat to safety. In the fire exposure tests performed the hazardousness of these vessels was demonstrated, since it was observed that not only fully charged acetylene cylinders but also cylinders with saturated solvent can explode, provided the heat transfer to the vessel is sufficient. The times to explosion were shorter for fully charged cylinders, due to the higher initial pressure and to the faster pressure increase. The effects of the explosions are comparable for both fully charged cylinders and for cylinders with saturated solvent, except for the smaller fireball which is produced in the second case, due to the smaller amount of fuel available. In both cases the cylinder walls or at least fragments can fly further than 100 m away from the burst location. Results of the experiments are presented in the paper. During the tests, temperature measurements at the cylinder walls and in the cylinder interior were performed. Furthermore, the pressure in the cylinder was recorded. The collected data will serve for the validation of a numerical model for the simulation of the heating of acetylene cylinders involved in fire and of the afterward cooling with water, which has been developed. The constitutive model equations and the results of some simulations are presented in the paper.
Determination of deflagration venting requirements in chemical/process plants is usually carried out using well established standards employing an empirically based formula. However, this formula is shown to have severe shortcomings, especially in the range of low KG-values, where either negative or inconceivably large venting areas can be predicted. Due to these shortcomings a method has been developed using the efflux function for gases as a basis to predict the mass flow through a vent opening in a vessel during an internal explosion. The simulated rise in pressure due to the internal explosion is quantitatively determined from the KG-value, with the mass flow through the vent opening in the vessel resulting from the pressure difference between the vessel and its surroundings. This enables the maximum overpressure as a function of the pressure relief surface area to be predicted. The method takes into account the temperature of the efflux gases and turbulence enhancement brought about by the venting process. In the following paper explosion pressure relief experiments are described and the results from these experiments are compared to predictions from the efflux method. It is shown that by adjusting the assumed turbulence which evolves during the venting process, the reduced explosion pressure can be reasonably well reproduced.
Scale-up experiments
(2004)
Hydrogen is a central component of the energy transition and the European Green Deal for a climate-neutral Europe. To be able to achieve the targets defined by 2045, the EU and the German government have drafted a framework for action and are making long-term investments in research, development and the rapid implementation of innovative hydrogen technologies.
The conditions for a successful energy transition and the economic use of green hydrogen as a clean energy carrier are Hydrogen readiness and a rapid market ramp-up, as well as the establishment of the necessary value chains in the national and European framework. Reliable quality and safety standards are the prerequisite for ensuring safety of supply and environmental compatibility and for creating trust in these technologies.
BAM has bundled its expertise in the field of hydrogen technologies into a competence center H2Safety@BAM to create confidence in the technology and to support the hydrogen strategies of the German government and the EU. The topic of hydrogen has been current at BAM for more than one hundred years and is also currently the focus of numerous research and cooperation activities. The competence centre H2Safety@BAM and its vision of “We build trust in hydrogen technologies” will be presented with its many safety-related topics, which can be found throughout the entire hydrogen value chain. Two deep dives will present the results on projects dealing with the design-to-cost issue of classical pressurized gas storage containments and the consequences of the release of liquid hydrogen, which will be roughly compared to the release of ammonia.