Filtern
Dokumenttyp
Schlagworte
- Deflagration (2)
- Druckentlastung (2)
- Berstfolie (1)
- Ceramic matrix composite (1)
- Ceria (1)
- Deflagrationen (1)
- Efflux (1)
- Explosion (1)
- Konstruktiver Explosionsschutz (1)
- Phase transformation (1)
Organisationseinheit der BAM
Es wurden Druckentlastungsvorgänge in einem 5 m³ Autoklav mit einem L/D-Verhältnis von 1,14 nach der Zündung von Methan-Luft-Gemischen untersucht. Schwerpunkt der Arbeit war die Bestimmung der Explosionsdrücke, der zeitlichen Druckanstiege bzw. der KG-Werte und der reduzierten Explosionsdrücke in Abhängigkeit der Methankonzentration. Im geschlossenen Behälter wurden die Explosionsdrücke und zeitlichen Druckanstiege für Methan-Luft-Gemische mit Methankonzentrationen von 5,9 Vol-% bis 13,5 Vol-% ermittelt. Die Ergebnisse zeigen gute Übereinstimmung mit den Literaturwerten. Weiter wurden Druckentlastungsversuche mit einer kreisrunden Entlastungsfläche von 0,011 m² und einer Druckentlastungsfolie mit einem statischen Ansprechdruck von 1,94 bar durchgeführt. Hierbei wurden Gemische mit Methankonzentrationen von 5,9 Vol-% bis 14,3 Vol-% untersucht. Dabei zeigte sich, dass die vergleichsweise kleine Entlastungsfläche nur dann zu reduzierten Explosionsdrücken gleich dem statischen Ansprechdruck der Berstfolie führte, wenn die Methankonzentration ≤ 5,9 Vol-% oder ≥ 14,0 Vol-% betrug. Bei allen anderen untersuchten Methankonzentrationen führten die durch die Druckentlastung induzierten Turbulenzen zu einer Beschleunigung der Verbrennungsreaktion und zu Explosionsdrücken vergleichbar denen im geschlossenen Behälter.
Determination of deflagration venting requirements in chemical/process plants is usually carried out using well established standards employing an empirically based formula. However, this formula is shown to have severe shortcomings, especially in the range of low KG-values, where either negative or inconceivably large venting areas can be predicted. Due to these shortcomings a method has been developed using the efflux function for gases as a basis to predict the mass flow through a vent opening in a vessel during an internal explosion. The simulated rise in pressure due to the internal explosion is quantitatively determined from the KG-value, with the mass flow through the vent opening in the vessel resulting from the pressure difference between the vessel and its surroundings. This enables the maximum overpressure as a function of the pressure relief surface area to be predicted. The method takes into account the temperature of the efflux gases and turbulence enhancement brought about by the venting process. In the following paper explosion pressure relief experiments are described and the results from these experiments are compared to predictions from the efflux method. It is shown that by adjusting the assumed turbulence which evolves during the venting process, the reduced explosion pressure can be reasonably well reproduced.
Ceramics and their composites are in general brittle materials because they are predominantly made up of ionic and covalent bonds that avoid dislocation motion at room temperature. However, a remarkable ductile behavior has been observed on newly developed 11 mol.% ceria-stabilized zirconia (11Ce-TZP) composite containing fine alumina (8 vol.% Al2O3) and elongated strontium hexa-aluminate (8 vol.% SrAl12O19) grains. The as-synthesized composite also has shown full resistance to Low Temperature Degradation (LTD), relatively high strength and exceptionally high Weibull modulus, allowing its use in a broader range of biomedical applications. In this study, to deepen the understanding of plastic deformation in Ce-TZP based composites that could soon be used for manufacturing dental implants, different mechanical tests were applied on the material, followed by complete microstructural characterization. Distinct from pure Ce-TZP material or other zirconia-based ceramics developed in the past, the material here studied can be permanently strained without affecting the Young modulus, indicating that the ductile response of tested samples cannot be associated to damage occurrence. This ductility is related to the stress-induced tetragonal to monoclinic (t-m) zirconia phase transformation, analogue to Transformation-Induced Plasticity (TRIP) steels, where retained austenite is transformed to martensite. The aim of this study is to corroborate if the observed plasticity can be associated exclusively to the zirconia t-m phase transformation, or also to microcraking induced by the transformation. The t-m transformed-zones produced after bending and biaxial tests were examined by X-ray refraction and SEM/TEM coupled with Raman. The results revealed that the observed elastic-plastic behavior occurs without extensive microcracking, confirming a purely elastic-plastic behavior driven by the phase transformation (absence of damage).
Der Einsatz von Druckentlastungseinrichtungen bietet bei sachgemäßer Auslegung eine sehr gute Variante, Behälter im Falle einer Explosion des im Innenraum vorhandenen Gasgemischs vor einer Zerstörung zu schützen. Die Auslegung von Druckentlastungseinrichtungen für Behälter erfolgt unter Anwendung verschiedener Standards und erfordert verschiedene Kenngrößen der involvierten explosionsfähigen Gasgemische.
Diese werden jedoch in der Regel im Labormaßstab bestimmt und dann auf den Industriemaßstab übertragen.
Viele Einflussgrößen und insbesondere die bei der Druckentlastung einsetzenden Turbulenzen werden nicht berücksichtigt. Fehldimensionierungen der Druckentlastungseinrichtungen sind möglich. In einer Forschungskooperation zwischen der BAM und der BASF AG werden experimentelle Daten für verschiedene Gassysteme im Technikumsmaßstab ermittelt, die später zur Validierung geeigneter Berechnungsmethoden verwendet werden sollen. Erste Ergebnisse werden vorgestellt.