Filtern
Erscheinungsjahr
Dokumenttyp
- Vortrag (56)
- Beitrag zu einem Tagungsband (32)
- Beitrag zu einem Sammelband (27)
- Zeitschriftenartikel (26)
- Forschungsbericht (4)
- Posterpräsentation (3)
- Buchkapitel (2)
- Sonstiges (1)
Schlagworte
- Non-destructive testing (14)
- Monitoring (8)
- Condition assessment (6)
- Inspection (6)
- Nondestructive testing (6)
- Concrete (5)
- Moisture (5)
- NDT (5)
- Strengthening (5)
- Zerstörungsfreie Prüfung (5)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (56)
Ultrasound sensors should be embedded into concrete for monitoring concrete properties. These new longitudinal wave sensors with a center frequency of 60 kHz were examined regarding their suitability for ultrasonic measurements in concrete structures in terms of emission characteristics, sensitivity and frequency ränge.
For the measurement of the radiation patterns, the sensors were embedded vertically and horizontally in concrete cylinders. The directivity pattern was measured using a laser vibrometer.
The sensitivity of the sensor was determined in water using different sensors of the same type. It shows changes in the signal amplitude as well as variations in the frequency ränge for different transmitter-receiver combinations.
The attenuation of the concrete affects the achievable resolution of the measurements and thus, the maximum possible spacing of the sensors within a concrete element. Experimental tests helped optimizing the distances with respect to the required resolution and the effort of embedding the sensors. The signal attenuation in the concrete was measured in the frequency ränge of 60 kHz in response to various degrees of reinforcement and grain size. For this purpose, the sensors were cast at different distances in the specimens studied. The recorded Signals were evaluated for their amplitude and frequency spectrum.
The research project "Ultrasonic Net for Concrete Monitoring (UNeCOM)" aims at developing a methodology for an embedded ultrasonic network for the condition assessment of infrastructure constructions. Civil engineering structures made of concrete, which are located in tectonically active regions or undergo special loading conditions, may require continuous monitoring. It is important to assess the condition of the building and its stability to recognise and classify the effect of a seismic event or evolving damage at early stages before failure occurs. Embedded ultrasonic sensors offer the possibility to detect changes in the material and degradation mechanisms from inside the structure in areas which are difficult or impossible to inspect otherwise. In contrast to conventional ultrasonic testing methods, where the concrete surfaces are scanned with ultrasound probes, this new approach uses sensors, which are embedded into concrete, eliminating the effect of variable coupling conditions between sensors and concrete. This method allows an integral detection of changes in the concrete structure, for example due to seismic activities, to detect mechanical impacts, as well as degradation of the material due to overloading. Such methods have great relevance especially for the monitoring of constructions like power plants, bridges, offshore structures and other structures with high technical safety requirements. The sensor network can be controlled remotely through the internet which is also being used for data transfer. The embedded sensor network is designed to monitor structural damage and concrete degradation globally with high sensitivity.
Nuclear Power Plants have been in operation for ca. 50 years. Based on this experience, non-destructive testing tasks specific to thick and highly reinforced nuclear containment structures have materialized. The performance based Service life extension of existing NPPs also needs a measurement based decision to support continuing the service of the concrete part of the installations.
By nature, concrete is a very durable material and any natural Deterioration processes may take a long time to become critical to the structure. The experience of more than 50 years of service limits the testing tasks to a few ones which are not yet solved.
Research in NDT of concrete structures is performed by many research institutions all over the world with different technical and systematic approaches. Results are mainly obtained on laboratory specimens, sometimes additional field studies are reported. This research takes place independently without coordination and as a result, the outcomes mostly lack full comparability.
Software for data analysis has become indispensable and very powerful. This part of testing needs more attention when it comes to evaluate test results. Validation of NDE solutions is becoming a critical part in concrete structure testing.
Validation is by definition the proof that a customer´s requirements in the test are being met by the testing solution. This includes equipment, personnel qualification and data analysis. In the following tables, the research recommendation Validation is used in the sense, that proof of the performance of existing solutions needs to be adressed. In general, a validation methodology for NDE solutions for concrete testing in itself needs to be researched and established.
Comparability of research also needs an accepted and easily accessible reference. From experience, it is almost impossible to manufacture exact copies of test specimens at different locations. Round Robin tests are therefore needed to evaluate the performance of a test.
Data evaluation is generally done using dedicated software, sometimes Hardware dependant and not interchangeable between systems. Software is ever more increasingly becoming more powerful and sophisticated. An in-depth evaluation needs to address the comparability and validation of Software used for data analysis and evaluation. The vision of a unified software pool for NDE investigations would undoubtedly support research tremendously.
Quantitative NDE is mostly recommended to assess the condition of a structure. However, qualitative data can be very useful, especially for processes which change the material properties or deteriorate the structure (e.g. corrosion of reinforcement). The need for reliable baseline data is a key factor for such monitoring tasks.
Laboratory model test for monitoring the new main railway station of Berlin - The Lehrter Bahnhof
(2002)
Adolf Martens (18501914) was a pioneer of materials engineering. After his studies in Berlin he joined a railway company being responsible for the technical equipment. His interest for the basic mechanisms of mechanical strength and fracture of metallic materials led him to the development of the basic concepts for metallography; his papers published between 1878 and 1889 laid the fundament of this technique. In 1880 Martens changed to the Royal Industrial Academy in Berlin and by 1884 he was designated as director of the Materials Testing Laboratory at the Technical University Berlin. Under his guidance this institution acquired an excellent reputation in all relevant areas of the German industry, forming the nucleus of the Bundesanstalt für Materialforschung und -prüfung (BAM) – the Federal Institute for Materials Research and Testing. Martens developed equipment in many different areas as mechanical testing of metallic materials and of paper, characterization of the wear behavior of materials and viscosity of lubricants. His overwhelming contribution to materials engineering was recognized as early as 1895 by Floris Osmond, who denominated martensite a metallographical constituent resulting from quenching of steels. In 2000 ISO designated the value obtained from the instrumented indentation method as Martens Hardness – HM.
Structural health monitoring contributes to early damage detection in the built infrastructure. During the last two decades, the sensor networks transferred from wired to wireless sensor networks.
Several methods exist to measure moisture in building materials. Most of the introduced commercial humidity measurement methods as provide information about the local or near surface moisture. A feasibility study is presented to demonstrate, how the Received Signal Strength Indicator (RSSI) of a BlueTooth® Low Energy (BLE) signal, transmitted from the BLE-module embedded in building materials with changing moisture content. The BLE-module communicates with a mobile Smart Device as tablet or mobile phone. The RSSI indicates to what extend the received signal strength is changed due to moisture, while the transmitted signal strength remains constant.
Structural health monitoring contributes to early damage detection in the built infrastructure. During the last two decades, sensor networks transferred from wired to wireless sensor networks. Several methods exist to measure moisture in building materials. Most of the introduced commercial moisture measurement methods provide information about the local or near surface moisture. A feasibility study is presented to demonstrate, how the Received Signal Strength Indicator (RSSI) of a Bluetooth Low Energy (BLE) signal, transmitted from the BLE-module embedded in building materials, correlate with changing moisture content. The feasibility of this influence was investigated in the presented study. The maximum and minimum RSSI were systematically recorded and analysed.
The presented development of a damping model is a research component of an experimental feasibility study about moisture in building materials measured with Bluetooth® Low Energy (BLE) signals. This study may be part of a structural health monitoring aiming on early damage detection in the built infrastructure and is increasingly focusing on wireless sensor Network technology. It is investigated, how the Received Signal Strength Indicator (RSSI) of a BLE signal, transmitted from the BLE-module embedded in building materials with changing moisture content is damped. The BLE-module communicates with a mobile Smart Device as tablet or mobile phone via 2.45 GHz-ISMfrequency band where water dipoles start to oscillate. If the BLE-signal transfers through a moist material, the moisture Content influences the RSS-Indicator. The damping model demonstrates this damping effect on RSSI by the abstraction of the reality observed in a real system.
The presented development of a damping model is a research component of an experimental feasibility study about moisture in building materials measured with Bluetooth® Low Energy (BLE) signals. This study may be part of a structural health- and long-term monitoring aiming at early damage detection in the built infrastructure and is increasingly focusing on wireless sensor network technology. It is investigated, how the Received Signal Strength Indicator (RSSI) of a BLE signal, transmitted from the BLE-module embedded in building materials with changing moisture content is damped. The aim of the modelling is the derivation of a damping equation for the formal model to determine the moisture damping exponent to finding a correlation.
This feasibility study presents how the Received Signal Strength Indicator (RSSI) of a Bluetooth® Low Energy (BLE) signal, transmitted from the BLE-module embedded in building materials with changing moisture content, is damped. The BLE-module (TRANSMITTER) communicates with a mobile Smart Device as tablet or mobile phone (RECEIVER) [Fig. 1]. The measured RSSI indicates to what extend the received signal strength is changed due to moisture, while the transmitted signal strength remains constant.
Concrete railway bridges - taxonomy of degradation mechanisms and damages identified by NDT methods
(2006)
CHEF provides knowledge about flood protection of cultural heritage objects and directly supports the European Floods Directive by giving recommendations on how to assess the vulnerability of monuments. A comprehensive analysis of protective measures BEFORE, DURING and AFTER a flood has been carried out within the project, including technical and administrational measures. An overview of these measures is given, followed by recommendations on how to establish the most effective protective strategies.
Assessment of existing steel structures - A guideline for estimation of the remaining fatigue life
(2007)
Assessment of existing steel structures - Recommendations for estimation of remaining fatigue life
(2008)
Die zunehmende Bedeutung der Nachhaltigkeit im Bauwesen wird in Zukunft das Bauen im Bestand gegenüber Neubauten in den Vordergrund rücken. Dies gilt auch für den Brückenbau, wo das Qualitätsmanagement seit langem Brücken von ihrem Entstehungsgang über den Betrieb bis in die Entsorgung begleitet.
Die starke Vergrößerung der Frachtvolumina für Straße und Schiene und die zunehmende Überalterung des Brückenbestandes fragen danach, ob die bestehenden Brücken für die veränderten Betriebsbedingungen noch geeignet sind und wie sie und ob sie dafür instandgesetzt werden könnten.
Für die erforderlichen Instandhaltungs- und Instandsetzungsmaßnahmen oder einen eventuellen Ersatz durch einen Neubau ist aber die Frage der Restnutzungsdauer von entscheidender Bedeutung. Es ist daher nicht von ungefähr, dass sich Baulast-träger auf nationaler und internationaler Ebene frühzeitig zusammengetan haben, um nach geeigneten Methoden der Bestimmung der Sicherheit und Restnutzungsdauer bestehender Brücken zu forschen. Auch die internationalen technisch-wissenschaftlichen Verbände wie EKS und fib sowie die Standard-Organisationen ISO und CEN sind der Frage eines internationalen Austauschs und der Vereinheitlichung der Methoden nachgegangen.
Für Stahlbrücken hat insbesondere das technische Komitee6 - Ermüdung - der EKS Anregungen aufgegriffen, aus den verschiedenen nationalen Erfahrungen und dem vorhandenen Wissen technische Empfehlungen für die Beurteilung bestehender Stahlbrücken zu entwickeln [1], die sich als Grundlage für die von CEN/TC 250 - das CEN-Komitee für die Bearbeitung der Eurocode - geplante Erweiterung der Eurocode zur Instandhaltung und Instandsetzung des Brückenbestandes eignen.
Das Ergebnis ist ein technisch-wissenschaftlicher Bericht, der im Rahmen der Zusammenarbeit der europäischen Kommission (DG-Research - Joint Research Centre JRC) mit der EKS als Basispapier für eine zukünftige Eurocode-Erweiterung veröffentlicht wurde und schon jetzt als Empfehlung für eine Vorgehensweise nach dem Stand der Technik verwendet werden kann.
Der vorliegende Beitrag behandelt die Grundzüge dieses Berichtes [1], der vom e-bookshop der Kommission kostenfrei herunter geladen werden kann.
Die Langzeitüberwachung von Bauteilen (Structural Health Monitoring, SHM) ging in den letzten Jahren zunehmend von verkabelten Sensoren zu kabellosen Sensornetzwerken (WSN) über. Frühwarnsysteme sollen rechtzeitige Signale senden, wenn Schädigungsprozesse einsetzen, wenn ein Bauteil z. B. zu feucht wird (Deiche, Staumauern), oder wenn Feuchteprozesse in Bauteilen auftreten, die den Transport von schädlichen Stoffen ermöglichen. Mittels handelsüblicher multifunktionaler Sensoren wie einem Bluetooth Low Energy (BLE) wurden erste Machbarkeitsuntersuchungen zur Massenfeuchtemessung durchgeführt. Die untersuchten Parameter sind der sogenannte Received Signal Strength Indicator (RSSI) eines Bluetooth-Low-Energy(BLE)-Signals und die abgestrahlte Sendeleistung eines eingebetteten BLE-Moduls. Das BLE-Modul kommuniziert mit einem mobilen smarten Empfänger wie einem Tablet oder einem Smartphone als SmartHub. Die Veränderung des RSS-Indikators ist ein Maß für die Veränderung der Feuchte im Bauteil, während die ausgesandte Signalstärke konstant bleibt. Wenn das BLE-Signal einen feuchten Bereich im Baumaterial durchläuft, verändert sich der RSS-Indikator. Nach erfolgreicher Machbarkeitsstudie wurde nun ein aus dem Netzwerk MI4G (Modern Industry for Germany) zwischen der Bundesanstalt für Materialprüfung und dem Klein- und mittelständigen Unternehmen LinTech GmbH heraus beantragtes ZIM-Projekt bewilligt. Der Bericht zeigt erste Ergebnisse von Voruntersuchungen und gibt einen Ausblick auf weitere Forschungsaktivitäten.
Within the presented research project, experimental and numerical investigations were performed to develop a thin-shelled, modular, mobile element system made of a micro-reinforced ultra-high-performance ductile concrete (DUCON®). Material parameters were experimentally determined to adapt the material model within the numerical analysis applying the Drucker-Prager relationship. Afterwards, for validation of the numerical models, quasi-static and high-velocity impact tests were performed on plate-like structures. Finally, a suitable geometry of transportable barrier elements will be designed, which provides a maximum of resistance against impact by a minimum of weight and a maximum of mobility.
Within the presented research project, experimental and numerical investigations were performed to develop a thin-shelled, modular, mobile element system made of a micro-reinforced ultra-high-performance ductile concrete (DUCON®). Material parameters were experimentally determined to adapt the material model within the numerical analysis applying the Drucker-Prager relationship. Afterwards, for validation of the numerical models, quasi-static and high-velocity impact tests were performed on plate-like structures. Finally, a suitable geometry of transportable barrier elements will be designed, which provides a maximum of resistance against impact by a minimum of weight and a maximum of mobility.
Inspection of steel bridges
(2007)
A new method for periodically monitoring reinforcement corrosion in concrete with Ground-Penetrating Radar (GPR) is proposed and a ten-year long-term corrosion periodic monitoring experiment is reported. GPR historical data was taken in different years, under different conditions. In order to align and normalize the obtained images properly prior to effectively performing any automatic defect detection, image registration techniques based on mutual-information are employed, and a new signal processing scheme is proposed for normalizing the intensity of GPR images. Then, the processed image results can be used to compare and find out the change of GPR detection due to corrosion.
Periodic mapping of reinforcement corrosion in intrusive chloride contaminated concrete with GPR
(2014)
This paper presents an experimental effort for developing a novel reinforcement corrosion monitoring technique based on Ground Penetrating Radar (GPR). Experiments were carried out to periodically monitor the accelerated reinforcement corrosion process with GPR. The data were processed in both time and timefrequency domains to investigate the tendencies of GPR signal attribute changes related with corrosion, moisture and chloride contamination. Data processing methods were proposed to visualize the reinforcement corrosion and chloride distribution with target specified signal attribute mapping. Half-Cell Potential (HCP) and Laser-Induced Breakdown Spectroscopy (LIBS) methods were employed to verify the GPR observations.
Monitoring accelerated corrosion in chloride contaminated concrete with ground penetrating radar
(2012)
In this article, we present a laboratory experiment to monitor the accelerated corrosion in concrete using ground-penetrating radar (GPR). Four concrete test specimens were cast with rebars of different size and placed at different depths. The lifetime decades of reinforcement corrosion process were accelerated into 18 days by using the impress current technique. The electrochemical corrosion process was periodically monitored with GPR. Two control specimens were also prepared to investigate the influence of chloride contamination on GPR signal. The measured data were analysed both in time and frequency domains. In time domain, the peak-to-peak amplitude of a wave reflected by a rebar was calculated to investigate the relationship between an increase in signal amplitude and the degree of corrosion. In frequency domain, the time–frequency representations of the signal were computed by using S-transform. The results show that reinforce corrosion increased the amplitude of reflected signal in time domain but did not change the peak frequency in frequency domain while chloride contamination attenuates the signal to smaller amplitude and lower peak frequency. Based on the results, a novel process is finally proposed for GPR-based corrosion detection.
In this research, laboratory experiments were carried out to investigate the feasibility of using ground penetrating radar (GPR) for corrosion detection and/or monitoring, and the mechanism of corrosion caused GPR signal changes, taking into account the influence of several parameters: Chloride, rebar size and cover depth. With the understanding of the mechanism, a novel method for detecting reinforcement corrosion in concrete with GPR is proposed, together with a series of signal processing toolkits for corrosion visualization and image comparison.
The Berlin Congress Hall was a gift of the United States of America to Germany for the Berlin World Exhibition in 1957. The elegantly double-curved roof was made from an advanced prestressed concrete construction. The construction followed the design by the American architect Hugh Stubbins with special structural modifications to comply with German construction rules. No early indications for failure initiation were detected before a sudden partial collapse. On May 21st, 1980, the Southern external roof overhang collapsed. In December 1980, Jörg Schlaich and his co-authors published a summarizing expert opinion about structural causes of failure. The present paper mainly introduces results of cause analysis made at the Federal Institute for Materials Research and Testing (BAM), mandated by the Public Prosecutor at the Berlin District Court to specify the causes of the sudden failure. This paper refers to BAM-publications about analyses that were performed under this mandate and published – most of them in German language – within the first years after failure. The expert's opinions comprise structural considerations materials investigations, metallographic analyses and corrosion. Nowadays experts have learnt from the failure and built a slightly modified roof in the original shape at the 750th birthday of the city of Berlin and re-opened the former Berlin Congress Hall to the public on May 9th, 1987. The Hall is now serving as the House of the Cultures of the World, following the initial intention of the hall.
A toolbox with non-destructive testing methods for the condition assessment of railway bridges
(2006)
The unified economic structure of the European market requires a unified transport infrastructure to ensure seamless and barrierfree transportation of passengers and goods. The European commission is funding the European Integrated Project Sustainable Bridges to comply with future traffic demands. The main objective of the project is to reliably assess and upgrade the bridge infrastructure for the required increase of axle loads and transport volume. 32 Institutes from 12 countries develop unified procedures for the assessment and improvement of the existing railway bridge stock under the guidance and review of six major European railway companies.
Non destructive testing (NDT) is given a high priority. One of the work packages concentrates on the potential of advanced NDT-methods and creates a toolbox with advisable methods for the condition assessment of all types of railway bridges. Although NDT-methods are implemented in the quality assurance process in many industries, their application in the railway infrastructure is not common. Only a few countries have included selected NDT-methods into advanced condition assessment procedures for the management of their bridge stock.
This paper describes also current activities to enhance pulse-phase thermography, impulse-radar and acoustic methods. The advanced methods enable infrastructure owners to verify construction plans, to assess structures, repair and strengthening quality or to identify in-service damages. Latest development is an automated scanning system for combined acoustic and electromagnetic measurements. The results are then combined through data fusion techniques to further increase their value for the bridge owners.
Complex special inspection of an old masonry arch bridge according to the Guideline on Inspection and Condition Assessment of Railway Bridges and numerical analysis of the structure are presented. The guideline summarises recommendations for the step-by-step investigation of railway bridges applying enhanced methods developed during the EU-funded project Sustainable Bridges. For the investigation of the arch barrel, the ballast parameters and the inner structure of the backfill behind the arch barrel a number of various advanced non-destructive and minor-destructive testing methods were applied. Deformation of the structure during load tests was measured using three independent measuring systems: laser vibrometer, LVDT and microwave radar. Results of calculations performed with 2D and 3D models based on FEM are compared with the field load tests. Sensitivity of the ultimate load of the structure to investigated parameters is studied in FE model. Some general conclusions according to methods of testing and modelling of masonry arch bridges are presented and discussed.
Complex special inspection of an old masonry arch bridge according to the Guideline on Inspection and Condition Assessment of Railway Bridges and numerical analysis of the structure are presented. The guideline summarises recommendations for the step-by-step investigation of railway bridges applying enhanced methods developed during the EU-funded project Sustainable Bridges. For the investigation of the arch barrel, the ballast parameters and the inner structure of the backfill behind the arch barrel a number of various advanced non-destructive and minor-destructive testing methods were applied. Deformation of the structure during load tests was measured using three independent measuring systems: laser vibrometer, LVDT and microwave radar. Results of calculations performed with 2D and 3D models based on FEM are compared with the field load tests. Sensitivity of the ultimate load of the structure to investigated parameters is studied in FE model. Some general conclusions according to methods of testing and modelling of masonry arch bridges are presented and discussed.