FG Füge- und Schweißtechnik
Refine
Year of publication
Document Type
Way of publication
- Open Access (5)
Keywords
- schweißen (13)
- fügen (12)
- Fügetechnik (8)
- Simulation (8)
- welding (5)
- Verzug (3)
- mechanical properties (3)
- model (3)
- simulieren (3)
- Al4043 (2)
Institute
Thermal shock behavior of ceramics plays a decisive role in their broad industrial applications. For
enhanced understanding of damage and failure mechanism under thermal shock loading, in the present
work, a combination of experimental testing and numerical simulation methods has been used. The
thermal shock behavior of the alumina (99.7%) disk samples has been investigated by using a plasma
test stand: the bottom of the ceramic disks were locally heated in the center by plasma beam; during the
heat treatment the temperature distribution at the top of the sample was recorded with a thermographic
system. To characterize the thermal shock resistance, a thermomechanical simulation was subsequently
carried out. It calculates the temperature and stress distribution within the ceramic disks. The
calculated critical thermal tension stresses are reported, which led to the failure of the ceramic disks
under thermal shock loading. The effect of the sample thickness on the temperature and stress
distribution is presented. Compared with the experimental results the simulated results show excellent
agreement. As conclusion, it is possible to determine the thermal shock behavior of ceramic materials by
the combination of experimental testing and numerical simulation.
Investigation of thermal shock behaviour of refractory ceramics based on the calcium-aluminate
(2015)
Leichtbau und das Streben nach Ressourcen- und Energieeffizienz fördern in den letzten Jahren vermehrt den Einsatz hochfester Stähle. Das Laserstrahlschweißen dieser Werkstoffe wird in der industriellen Großserienferti-gung zur effizienten Herstellung hochpräziser Bauteile und Komponenten mit höchsten Qualitätsanforderungen eingesetzt. Die Vermeidung schweißbedingter Fehler wie Schweißverzug und Kaltrissbildung sind dabei von ent-scheidender Bedeutung. Konventionelle Anwendungen erfüllen diesen Anspruch derzeit bedingt durch sehr enge Prozesstoleranzen und die Auswahl unkritischer Werkstoffe, was die Potentiale der Fügeverbindung begrenzt. Auf Basis von FE-Schweißprozesssimulationen konnten Konzepte entwickelt werden, welche eine Verzugs- und Riss-minderung durch aktive Steuerung des Laserschweißprozesses ermöglichen. Die zugrundeliegenden Modelle be-rücksichtigen zum einen das schweißbedingte Temperaturfeld, Gefügeumwandlungen und Eigenspannungen für die Berechnung des Verzugs. Zudem wird die lokale Wasserstoffkonzentration berechnet und die Ergebnisse der Schweißprozesssimulation mittels eines Kaltrisstools bewertet, welches werkstoffspezifische Risskriterien enthält. Die Fähigkeit das Verzugs- und Kaltrissverhalten abzubilden, eröffnet die Möglichkeit zur Parametervariation. Aus den erhobenen Daten wurden Konzepte der aktiven Krafteinleitung mit einer dynamischen Werkstückeinspannung abgeleitet, die zu Verzugs- und Kaltrissminimierung führen und die Schweißbarkeit hochfester Werkstoffe fördern.
Investigations on the thermal conditions during laser beam welding of high-strength steel 100Cr6
(2023)
This study examines the thermal conditions during laser beam welding of 100Cr6 high-strength steel using a TruDisk5000 disc laser with a continuous adjustable power range of 100–5000 W. Two parameter sets, characterized by laser power and welding speeds, were analyzed by thermal-metallurgical FE simulations to determine their impact on the thermal conditions during welding. The results show a significant shift in heat coupling, with conduction transitioning to deep penetration welding. As a result of the high welding speeds and reduced energy input, extremely high heating rates up to 2∙104 K s−1 (set A) respectively 4∙105 K s−1 (set B) occur. Both welds thus concern a range of temperature state values for which conventional Time-Temperature-Austenitization (TTA) diagrams are currently not defined, requiring calibration of the material models through general assumptions. Also, the change in energy input and welding speed causes significantly steep temperature gradients with a slope of approximately 5∙103 K mm−1 and strong drops in the temperature rates, particularly in the heat affected zone. The temperature cycles also show very different cooling rates for the respective parameter sets, although in both cases they are well below a cooling time t8/5 of 1 s, so that the phase transformation always leads to the formation of martensite. Since the investigated parameters are known to cause a loss of technological strength and conditionally result in cold cracks, these results will be used for further detailed experimental and numerical investigation of microstructure, hydrogen distribution, and stress-strain development at different restraint conditions.
Crystallography and Mechanical Properties of Wire Arc Additively Manufactured Al5356 Components
(2021)
In this study, we present results of the evolution of the crystallographic texture and imperfections, as well as the corresponding mechanical properties of wire and arc additively manufactured (WAAM) Al5356 specimens, studied by X-ray diffraction (XRD) and tensile testing, respectively. The results show that the phase composition is in the form of a face-centred cubic (fcc) crystal structure, corresponding to the base material, as well as some traces of oxide phase Al2O3. The WAAM specimen growing is accompanied by a slight change in the preferred crystallographic orientation, from (111) to (200) and a decrease in the imperfections concentration. Also, it was found that the ultimate tensile strength (UTS), yield strength (YS), and elongation slightly decrease from the initial to the more advanced stages of growth.
The Influence of Geometrical and Welding Imperfections on the Strength of Stiffened Structures
(2018)
The strength calculation of stiffened plates and shells via finite element simulation has been part of the state of the art for a long time. Geometrical nonlinearities as well as the nonlinear material behavior are considered within the calculation. To simplify, both types of imperfections, geometrical and structural ones, are mostly combined in these strength calculations being considered as equivalent geometrical imperfections. Values for standard cases are included in EN 1993-1-5 in case of plated structures or 1-6 in case of shells. A second possibility is the separate definition of fabrication tolerances and residual stresses, as far as they are known. With increasing complexity of the structure, less information are however available on geometrical and particularly structural imperfections. Nevertheless, by means of a more realistic consideration of these values, the actual ultimate load can be determined significantly more exactly and the performance of high performance steel structures is increased.
In the investigated cases, deformations and stresses arise mainly due to welding. Therefore, the topic of this article is the application of an analytical numerical hybrid model for predicting imperfections induced by welds. This is presented on an example of a stiffened steel structure and a subsequent ultimate load calculation. At the beginning the analytical model, its physical basis as well as the physical interrelationships are introduced and explained. This is followed by the explanation of the coupling procedure between the analytical model and the numerical calculation for the calculation of weld-induced deformations and residual stresses. The significance of the hybrid model is proven by means of a few sample applications. For a realistic determination of the weld imperfections in the investigated stiffened structure, the coupled hybrid model is used afterwards. An ultimate load analysis gives information about the load carrying behavior under axial loading. The results are compared with the results of an ultimate load analysis from a literature example assuming different eigenvalues with different scaling. The results underline the potential additional utilization of load bearing capacity by this new approach.