FG Füge- und Schweißtechnik
Refine
Year of publication
- 2022 (5) (remove)
Document Type
Way of publication
- Open Access (1)
Keywords
- AA2024 (1)
- Al4043 (1)
- AlSi5 (1)
- computational welding mechanics (1)
- deformation (1)
- electron beam welding (1)
- eutectic formations (1)
- heat input (1)
- hot crack susceptibility (1)
- impulse friction stir welding (1)
Institute
Durch den strukturellen Einsatz von Faser-Kunststoff-Verbunden (FKV) lassen sich hochwertige gewichtsoptimierte Karosserien in Mischbauweise umsetzen. Die untersuchte CMT-Pin-Schweißtechnik zur Verbindung von thermoplastischen Organoblechen mit Stählen bietet, im Vergleich zu anderen Verfahren, neben einer einseitigen Zugänglichkeit, ein hohes Leichtbaupotenzial. Das Vorhaben wurde auf eine werkstoff-, prozess- und konstruktionsgerechte Umsetzung des Verfahrens ausgerichtet.
Auf Basis experimenteller und numerischer Untersuchungen wurde eine Methode zum Vorwärmen von Organoblechen mittels Infrarotstrahlung entwickelt. Die Eignung der CMT-Pin-Technologie wurde sowohl für das Fügen von karbon- als auch glasfaserverstärktem PA6 betrachtet. Als Bewertungskriterien wurden das Schweißgut sowie der Faser- und Matrixerhalt in Abhängigkeit der Schweißparameter untersucht. Das entwickelte Verfahren wurde mit herkömmlichen Fügemethoden bzgl. der in Kopf- und Scherzugversuchen ermittelten Festigkeiten verglichen. Zur Bestimmung der Beständigkeit der Verbindungen gegen unterschiedliche Witterungsbedingungen wurden Salzsprühnebel- und Wechselkorrosionstests durchgeführt. Mit dem Fügen von Hutprofilen wurde die Anwendung der entwickelte CMT-Pin-Technik am Tunnel sowie den Längs- und Querträgern der Bodenstruktur eines Kraftfahrzeugs demonstriert.
Microhardness variations across the friction stir welded (FSW) and impulse friction stir welded (IFSW) AA2024–T351 joints have been elucidated by the transformations of the S–Al2CuMg phase with a special focus on a distinguished hardness peak within the heat-affected zone (HAZ) of the impulse welds. The increase in hardness within the stir zone (SZ) originated from the partial re-precipitation of the initial Guinier-Preston-Bagaryatsky zones (GPB) and metastable S needles, previously dissolved.) Formation and growth of stable S precipitates via coalescence accounted for the softening through the thermo-mechanically affected zone (TMAZ). The peak strengthening within the HAZ of the IFSW joints was mainly caused by the dense needle-shaped S particles, which can be explained by a mutual influence of the process specific temperature and strain cycles. Dislocations and subgrain boundaries introduced to the material due to plastic deformation facilitated the nucleation of strengthening S precipitates in the HAZ. It demonstrates that the impact of deformation should be considered by the characterization of the precipitation development in the HAZ.
For the purpose of this research, single track details were manufactured in the shape of thin walls with a length of 100 mm and a height of 80 mm. Two welding speeds were chosen for this experiment–13.3 mm/s and 20.0 mm/s corresponding to the following heat inputs: 120 J/mm and 80 J/mm. The gas metal arc welding (GMAW) method was used for the build-up of the specimens in the cold arc pulse mode. The structure of the specimens was studied using X-ray diffraction (XRD) analysis carried out with CuKα radiation with a wavelength of 1.5406 Ǻ, optical microscopy, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDX). Furthermore, the Vickers hardness of the samples was determined using a ZwickRoell DuraScan 10/20 G5 unit at a force of 1 N. A preferred crystallographic orientation towards the (200) plane was observed in all cases, however a vastly textured structure was observed with inclusions of peaks in the (111), (220), and (311) crystallographic planes. The full width at half maximum (FWHM) of samples taken from different stages of build-up was calculated indicating an increase of the dislocation density at the more advanced stages of specimen growth. Despite that an increase of the hardness was observed towards the top of both specimens. This is attributed to the change in the structure of the αAl + Si formations from an irregular one at the bottom of the specimens, towards a fibrous one at the top. The results are discussed in regard to the optimization of the build-up process during wire arc additive manufacturing (WAAM).
Among different joining methods, the electron beam welding is recently applied for manufacturing of turbine components from temperature-resistant nickel-based conventionally cast Alloy 247 LC CC. However, the high tendency to hot cracking, in particular the formation of solidification cracks, remains a major challenge. Experiments indicate a significant reduction in hot cracks if the welding is performed outside the common welding parameter range. To understand these observations, a study of local thermo-mechanical conditions during electron beam welding of Alloy 247 samples was carried out using numerical simulations. The results were subsequently compared with reference test welds. For this purpose, a finite element model for coupled transient thermal and mechanical analysis was created and used. The work presents a comparative analysis of the evolution of strain components in brittle temperature range during cooling, considering the distribution and orientation of the cracks. Various relations between local strain kinetics and crack appearance, with notable influence of the plastic strain vector, were observed. Finally, the aspects of assessment of hot crack susceptibility with aid of thermo-mechanical welding simulation are discussed.
The beam inclination leads to a change in the laser spot size on the material surface. The higher the inclination, the larger the irradiated area and the lower the laser intensity. Moreover, if the material surface is outside of the beam focal plane, the intensity distribution profile becomes asymmetric. In this study, a heat source model, which calculates the intensity distribution on the workpiece surface as a function of beam parameters (beam waist, divergence half-angle) and process parameters (laser power, incidence angle, and distance to focal plane) was developed. The applicability of the heat source model was demonstrated by simulating 4 different laser hardening regimes. Once the heat efficiency coefficient had been calibrated the developed finite-element model allowed computation of temperatures while hardening with perpendicular laser beams as well as with inclined beams. The open-source software FEniCSx was used for the finite element computations. The mathematical formulation, required for performing temperature simulations with FEniCSx was briefly introduced.