Ingenieurwissenschaften und zugeordnete Tätigkeiten
Filtern
Dokumenttyp
- Vortrag (5)
Sprache
- Englisch (5)
Referierte Publikation
- nein (5)
Schlagworte
- Ultrasound (5) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (5) (entfernen)
Ultrasonic guided waves interacting with complex geometrical features are of high interest in the SHM field. For example, investigations into the extent to which a small change in defect geometry affects wave propagation have applications in Probability of Detection and defect reconstruction. These fields have to be supported by numerical tools aiming to retrieve accurate and reliable results and, thus, more realistic modeling.
Due to the short wavelengths of ultrasonic waves and the relatively large domains in which the waves propagate, fine grid resolution for the entire domain is usually not possible due to limited computational resources. One solution is to partition the domain into different subdomains and use a specific, efficient approach for each subdomain.
This contribution shows a combination of methods that aims to study these wave defect interactions in an elastic media. Firstly we introduce high-order 3D meshes that can resolve very fine geometrical details and are based on an Octree discretisation technique that employs special transition shape functions to resolve the hanging nodes that may appear due to the nature of the method. Afterward, the Octree mesh is embedded in a prismatic wave-guide based on the semi-analytical formulation of the SBFEM in 3D. To couple the different domains, we employ the mortar method, which enforces the continuity of the wave field across the internal boundaries of the domains. Examples show the power of the approach especially when it comes to parametric analysis.
The homogeneous introduction of organic additives is a prerequisite for good processability of ceramic powders during dry pressing. The addition of organic additives by wet route via ceramic slurries offers advantages over dry processing. The organic content can be reduced and a more homogeneous distribution of the additives on the particle surface is achieved. In addition to the measurements of zeta potential and viscosity, sedimentation analysis by optical centrifugation was also tested and successfully used to characterize the ceramic slurries and accurately evaluate of the suitability of different types, amounts, and compositions of organic additives.
Spray drying of well-stabilized slurries usually results in mostly hollow granules with a hard shell leading to sintered bodies with defects and reduced strength and density. By purposefully degrading the slurry stability after dispersion of the ceramic powder, the drying behavior of the granules in the spray drying process and thus the granule properties can be influenced. Destabilization of the slurry and thus partial flocculation was quantified by optical centrifugation. Spray drying of the destabilized alumina slurries resulted in "non-hollow" granules without the detrimental hard shell and thus improved granule properties.
Further improvement of the granules was achieved by installing ultrasonic atomization in the spray dryer. A narrower granule size distribution was achieved, which had a positive effect on, among other things, the flowability of the granules.
Specimens produced from this granules had fewer defects of smaller size, leading to better results for the density and strength of the sintered bodies. The observations made for alumina could be transferred to zirconia and as well to ZTA with 20 wt% zirconia.
Dry pressing of ceramic materials requires homogeneously soft granules with good flowability to allow rapid die filling and to avoid packing defects. Spray-drying granulation appears to be the best method for obtaining granules with high flowability in industrial scale. But, strength reducing internal microstructural defects caused by spray-dried granules with hollow and hard shells are often observed using nano and/or multi-component starting powders.
Using the example of a ZTA composite, the potential of slurry optimization, ultrasound atomization and infrared drying for better granule properties and compaction behavior were investigated. Starting granules produced in a conventional spray dryer (Niro, Denmark) with a two fluid nozzle showed typical defects like large central pores and dimples.
The early step of slurry preparation already possesses an essential optimization possibility in the form of stability adjustments. Granule compaction was clearly improved upon a specific reduction in slurry stability. The second optimization opportunity to improve the granule quality was the atomization step. Implementation of an ultrasound atomizing unit into the conventional spray dryer positively affected granule size distribution and therefor flowability and as well granule yield. But, a combination of both process optimizations delivered the best sinter bodies with highest density and strength due to further reduction in maximum size and fraction of pores.
As last step of a spray drying process, the drying is the focus of further investigations. A current setup implying a spray dryer prototype utilizes stacked infrared heater in a countercurrent setup delivering a further increase in granule yield and enduring spraying process stability.
Due to the market needs on steel for high demanding applications non-destructive methods for the determination of steel cleanliness using ultrasound have to be adapted to increase sensitivity respectively.
The basic idea is that the new standard proposal should follow the basic line outs from SEP 1927 and ASTM E588. Additional to these relatives the standard should be open to different types of specimen and inspection frequencies to cover a wide range from bars, rings and plates as well as different inspection sensitivities. For an enhance in resolution the standard draft focuses on immersion focal beam probes which should be selected according to the geometry of the specimen. The selection should be proved with the aid of simulation tools. The frequency shall be at least 10 MHz. For specimen thicknesses of less than 6 mm a frequency of at least 25 MHz shall be used.
Calibration procedures had to be improved significantly compared to the old standards to allow proper sizing of indications. Therefore calibration procedures shall take signal processing into account. For detailed evaluation of the amplitude dependency and for calibration a reference block with a sufficient number of reflectors has to be used. The recorded echo height shall be directly transferred into an equivalent disc shaped reflector EDSR by a distance amplitude curve.
The novelty in this standard draft will be that based on 3D measurements and 3D evaluation the amplitude criterion of an indication becomes just one among some other criteria. This standard takes the signal amplitude, signal amplitude distribution and signal travel time for classification into account.
The standard draft will be open to the definition of the volume to be investigated to be set by the user. This will make evaluation more comparable to other methods because the inspected area has to be user defined.
We recommend CEN/TC 138 to decide on a work item for this proposal to become an EU and an ISO standard using Vienna agreement.
The research leading to these results has received funding from the European Union's Research Fund for Coal and Steel (RFCS) research programme under grant agreement n° RFSR-CT-2013-00014.
Advanced spray drying process by controlled slurry destabilization and ultrasonic atomization
(2017)
Spray drying of ceramic slurries aims for soft and free-flowing granules with homogenous microstructure suitable for uniaxial and isostatic pressing. A stable and continuous spray drying process of slurries with maximized solids content is a further development target, since a reduction of the energy intensive drying procedure is desirable.
First part of the investigation focuses on the development of an appropriate zirconia slurry for spray drying with optimized organic additive contents (dispersant + binder + pressing and lubricating agents). Characterization and improvement of slurries are based on zeta potential measurements and investigations of the sedimentation behavior in an optical centrifuge. Therefor the slurries were spray dried with a conventional spray dryer with a two stream nozzle run in fountain mode. The controlled destabilization of the slurries was introduced, since the unwanted formation of hard granules with donut-like shape could be circumvented. Spray drying of such modified slurries resulted in soft granules without voids and finally leaded to sintered bodies with improved microstructure, density and bending strength.
Expectedly, the destabilization process causes a significant increase in viscosity of the ceramic slurry. Hence, an alternative spraying concept utilizing an ultrasonic nozzle was tested. Indeed, the ultrasonic nozzle seems able to atomize slurries with viscosities beyond the capability of the regular two stream nozzles due to the slurry’s shear thinning behavior. In second part of the investigation the integration of the ultrasonic nozzle in a commercial spray dryer is shown and first results of the spraying tests are discussed. Continuous spraying processes of highly viscous alumina, zirconia and ZTA slurries were realized over an extended production period.