Ingenieurwissenschaften und zugeordnete Tätigkeiten
Filtern
Dokumenttyp
- Posterpräsentation (60) (entfernen)
Referierte Publikation
- nein (60)
Schlagworte
- Additive manufacturing (15)
- Additive Manufacturing (11)
- Computed tomography (11)
- Laser powder bed fusion (7)
- Computed Tomography (6)
- Residual stress (6)
- X-ray refraction (6)
- Microstructure (4)
- AlSi10Mg (3)
- Laser Powder Bed Fusion (3)
- Neutron diffraction (3)
- Residual Stress (3)
- Röntgenrefraktion (3)
- Synchrotron tomography (3)
- Ti-6Al-4V (3)
- X-ray fluorescence (3)
- AGIL (2)
- Absorption edge tomography (2)
- Additive Fertigung (2)
- Computertomographie (2)
- Dental materials (2)
- In situ heating (2)
- LTCC (2)
- Laser Beam Melting (2)
- MMC (2)
- Machine Learning (2)
- Metals (2)
- Metrology (2)
- Neutron Diffraction (2)
- Online Process Monitoring (2)
- Powder Bed Fusion (2)
- Selected Laser Melting (2)
- Selective laser melting (2)
- Synchrotron X-Ray Refraction (2)
- Synchrotron X-ray computed tomography (2)
- Thermally induced porosity (2)
- X-ray computed tomography (2)
- X-ray diffraction (2)
- 316L (1)
- 5G (1)
- AM IN718 (1)
- Additive Fertigung (AM) (1)
- Advanced manufacturing (1)
- Air Void System (1)
- Al alloy (1)
- AlSi10Mg alloy (1)
- Aluminium (1)
- Aluminium alloys (1)
- BAMline (1)
- Bench braking sequence (1)
- Bildverarbeitung (1)
- Bronze (1)
- Build Angle (1)
- Bulk properties ageing (1)
- CMAS (1)
- CMAS - Calcium-Magnesium-Aluminiumsilikat (1)
- Carbon Fiber Reinforced Plastics (1)
- Characterization (1)
- Crack evolution (1)
- Crack propagation (1)
- Creep (1)
- DED-L (1)
- DIC assisted compression (1)
- Damage (1)
- Damage mechanism (1)
- Data fusion (1)
- Dental material (1)
- Diesel (1)
- Diffraction Enhanced Imaging (1)
- EBSD analysis (1)
- EMN (1)
- Eigenspannung (1)
- Electron Backscatter Diffraction (1)
- Electron microscopy (1)
- European Metrology Network (1)
- Fe2TiO5 (1)
- Fiber reinforced dental post (1)
- Fiberglass composite (1)
- HDPE Sorption (1)
- Heat Treatment (1)
- Heat treatment (1)
- High Temperature Testing (1)
- Holz (1)
- IN 625 (1)
- IN718 (1)
- Implants (1)
- In situ tensile test (1)
- In situ testing (1)
- In-situ compression CT (1)
- In-situ heat treatment (1)
- In-situ tomography (1)
- In718 (1)
- JNP AdvManuNet (1)
- Kavitation (1)
- Keramik (1)
- L-PBF (1)
- L-PBF 316L (1)
- LMD (1)
- LPBF (1)
- LTCC multilayer (1)
- Lattice structure (1)
- Lightweight structures (1)
- Load Partition (1)
- Load history (1)
- Load transfer (1)
- Low Cycle Fatigue (1)
- Low cycle fatigue (1)
- MOF (1)
- Machine-Learning Segmentation (1)
- Mechanical Behavior (1)
- Metal Matrix Composite (1)
- Metal matrix composite (1)
- Metal organic framework (1)
- Micro computed tomography (1)
- Mikro-CT (1)
- Mikrostruktur (1)
- Neutronbeugungsverfahren (1)
- Non-destructive testing (1)
- Numerische Simulation (1)
- Polyamid 12 (1)
- Porosity (1)
- Porosity growth (1)
- ProMoAM (1)
- Propagation modes (1)
- Prozessmonitoring (1)
- Residual stress measurements (1)
- Residual stress state (1)
- Roughness (1)
- Röntgen-Refraktion (1)
- Röntgenbeugung (1)
- SLM (1)
- SXRR - Synchrotron X-ray Refraction Radiography (1)
- Scaffold (1)
- Selective Laser Melting (1)
- Semi-metallic friction material (1)
- Stainless Steel (1)
- Subgrain structure (1)
- Synchrotron CT (1)
- Synchrotron Tomography (1)
- Synchrotron X-ray Refraction (1)
- Synchrotron X-ray diffraction (1)
- Synchrotron X-ray refraction (1)
- Synchrotron X-ray refraction radiography (1)
- Synchrotron refraction radiography (1)
- TBC (1)
- Tensile Properties (1)
- Thermal arrier coatings (1)
- Thermal barrier coatings (1)
- Thermoelectrics (1)
- Thermography (1)
- Titanium (1)
- Torsional fatigue (1)
- Verbundwerkstoffe (1)
- Vitual computer tomography simulation (1)
- X-Ray Diffraction (1)
- X-ray Diffraction (1)
- Zahnmedizin (1)
- ZfP (1)
Organisationseinheit der BAM
- 8.5 Röntgenbildgebung (60) (entfernen)
Additive Manufacturing by Selective Laser Melting (SLM) offers an ample scope for producing geometrically complex parts as compared to the traditional subtractive manufacturing strategies. However, the residual stresses (RS) developed during the processing can reduce the load bearing capacity as well as induce unwanted distortion, limiting the life time and the application of SLM parts.
In order to provide further evidence of damage mechanisms predicted by the solid-state transformation creep (SSTC) model, direct observation of damage accumulation during creep of Al–3.85Mg was made using synchrotron X-ray refraction (SXRR). X-ray refraction techniques capture the specific surface (i.e. surface per unit volume) with a field of view comparable to the specimen size but with microscopic sensitivity. A significant rise of the internal specific surface with increasing creep time was observed, providing evidence for the creation of a fine grain substructure, as predicted by the SSTC model.
Additive manufacturing (AM) offers an effective solution to the medical sector. It enables the production, on demand, of customised implants which match the patient’s anatomy, with grafts that promote bone growth, as well as surgical guides that help the surgeons.
The objective of this project is to provide a comprehensive basis to enable the safe use of medical AM products with traceable and reliable dimensionalmeasurements. This will guarantee the reliability of medical AM products to notified bodies and facilitate acceptance of AM in the medical sector for a better quality of life.
Two metal matrix composites, both consisting of a near-eutectic cast AlSi12CuMgNi alloy, one reinforced with 15%vol. Al2O3 short fibers and the other with 7%vol. Al2O3 short fibers + 15%vol. SiC particles were studied. Distribution, orientation, and volume fraction of the different phases was determined by means of synchrotron computed tomography. The load partitioning between phases was investigated by in-situ neutron diffraction compression tests. The internal damage of the eutectic Si phase and Al2O3 fibers after ex-situ compression tests was directly observed in CT reconstructed volumes. Significant debonding between Al-matrix and SiC particles was found. Those observations allowed rationalizing the load transfer among the constituent phases of two different composites. Finally, based on the Maxwell scheme, a micro-mechanical model was utilized for the composite with one and two ceramic reinforcements. The model rationalizes the experimental data, and predicts the evolution of principal stresses in each phase.
Influence of deposition hatch length on residual stress in selective laser melted Inconel 718
(2018)
The present study aims to evaluate the bulk residual stresses in SLM parts by using neutron diffraction measurements performed at E3 line -BER II neutron reactor- of Helmholtz-Zentrum für Materialien und Energie (HZB) Berlin. Together with microstructure characterization and distortion measurements, it is possible to describe the stress state throughout the whole sample. The sample was measured in as-build condition (on a build plate) and after releasing from the build plate. The used material is the nickel based superalloy 718. This alloy is widely used in aerospace and chemical industries due to its superior corrosion and heat resistant properties.
Obtained results indicated different residual stress states for each of the transversal, longitudinal and normal component. The normal and transversal component exhibits a rather compressive behavior while the longitudinal was tensile in the center part of the sample and became compressive towards the tip. As expected, the absolute values of all stress components decreased after releasing the sample from the building plate. A surface scan utilizing a coordinate-measuring machine (CMM) allowed us to present top surface distortion before and after releasing. The top surface showed a distortion around ±80µm after releasing. Microstructure evolution in the scanning-building cross-section is largely dominated by columnar grains. In addition, many small random orientated grains are prominent in the regions of a laser overlap during SLM.
In summary, for the sample of superalloy 718 manufactured by SLM, a small distortion occurred when removing the sample from the build plate whereby the residual stress state decreases. Moreover, the observed columnar grains in the building direction could give a reason for the lowest stress values in that normal direction. However, the most important parameter controlling the residual stresses is the temperature gradient. Hence, future investigations are planned for a different scan strategy to distribute the laser impact in a more homogenous manner.
The layer-by-layer Additive Manufacturing (AM) by means of Selective Laser Melting (SLM) offers many prospects regarding the design of a part used in aeroplane components and gas turbines. However, structural deviations from the nominal morphology are unavoidable. The cooling of the finished part leads to shrinkage and a high surface roughness is induced by attached powder particles affecting the part volume too.
The integrity and load-bearing capacity of a SLM produced lattice structure (see Fig.1) has been investigated by means of in-situ X-ray computed tomography during compression. The lattice structure was compressed by 10 % in height with an applied maximum force of 5 kN. Additionally, a single strut has been investigated ex-situ as a component of the lattice structure. With the higher resolution achieved on the single strut, the pore distribution (size and location) as well as the surface roughness were assessed. One of the main results coming from the in-situ analysis was that the nodes were identified as the weakest points in the lattice structure.
Additive manufacturing (AM) offers an effective solution to the medical sector. It enables the production, on demand, of customised implants which match the patient’s anatomy, with grafts that promote bone growth, as well as surgical guides that help the surgeons. The objective of this project is to provide a comprehensive basis to enable the safe use of medical AM products with traceable and reliable dimensionalmeasurements. This will guarantee the reliability of medical AM products to notified bodies and facilitate acceptance of AM in the medical sector for a better quality of life.