Ingenieurwissenschaften und zugeordnete Tätigkeiten
Filtern
Erscheinungsjahr
- 2017 (7) (entfernen)
Dokumenttyp
- Vortrag (7) (entfernen)
Referierte Publikation
- nein (7) (entfernen)
Schlagworte
- BAM-Liste (2)
- Aged biodiesel (1)
- Aged heating oil with 10% biodiesel (B10) (1)
- Beständigkeit (1)
- Beständigkeitsbewertung (1)
- Biodiesel (1)
- Bioethanol (1)
- Biokraftstoffe (1)
- Compatibility (1)
- Corrosion resistance (1)
Eingeladener Vortrag
- nein (7)
Die BAM-Liste - Anforderungen an Tanks für die Beförderung gefährlicher Güter – mit den Beständigkeitsbewertungen metallischer und polymerer Werkstoffe ist Grundlage für die stoffbezogenen Baumusterzulassungen für Tankcontainer und ortsbewegliche Tanks zur Beförderung gefährlicher Güter durch die BAM seit der Herausgabe der 1. Auflage 1989. Diese Beständigkeitsbewertungen werden nicht nur bundesweit, sondern weltweit als Erkenntnisquelle genutzt. Für die Zulassung von Kesselwagen und Tankfahrzeugen werden diese Daten auch herangezogen. Die Werkstoffbeständigkeitsdaten und der damit verbundene Informationsservice der BAM haben mit Sicherheit dazu beigetragen, Leckagen von Tanks aufgrund des Einsatzes von Tanks/Kesselwagen aus einem gegenüber dem Füllgut unbeständigem Tankwerkstoff oder Dichtungswerkstoff zu vermeiden.
The objective of this research was to determine the resistance of frequently used sealing materials such as EPDM, FKM, FVMQ, CR, CSM, IIR, NBR, PA, PUR and VMQ in aged biodiesel and heating oil B10 with 10 % biodiesel.
The mass, tensile strength, breaking elongation and Shore hardnesses of the test specimens were determined before and after exposure in non-aged, one-year, two-year, three-year and four-year aged biodiesel and B10 at 20 °C, 40 °C and 70 °C.
A threshold for the reduction in tensile properties and Shore hardness is not set in the international standards. Therefore, a threshold of 15 % was set for the evaluation of the compatibility. The decrease in tensile properties and Shore hardness increased with the age and the temperature of the biodiesel and the heating oil.
The age of the biodiesel was not relevant for the sealing materials CR, CSM, EPDM, IIR and NBR, which were generally not resistant to biodiesel and B10. FKM and PA showed high compatibility in non-aged and aged biodiesel. FVMQ and PA could be evaluated as resistant in non-aged and aged B10 at 20°C and 40°C, whereas FKM was resistant up to 70°C despite of the age of B10.
Changes in fuel composition and the introduction of alternative fuels often create problems of corrosion and degradation in materials. The objective of this research was to determine the corrosion behaviour of commercial metallic tank materials (unalloyed steels, austenitic CrNi- and CrNiMo-steels, aluminium and its alloys) in fuels and heating oil with admixtures of biogenic sources, such as gasoline with addition of ethanol (E10, E85), pure biodiesel and heating oil with 10 % biodiesel (B10).
Metallic tank materials were evaluated as resistant in a liquid if the annual corrosion rate due to uniform corrosion did not exceed 0.1 mm/year, and localized corrosion effects in the form of pitting corrosion, stress corrosion cracking and crevice corrosion did not occur.
The corrosion rates of the tank materials after exposure to E10, E85, non-aged and two-year aged pure biodiesel, and non-aged and one-year aged heating oil B10 for four weeks at 50 °C, according to DIN 50905/4, were well below the limit of 0.1 mm/year. For the unalloyed steels, the formation of rust was observed independently of the biofuels amount of ageing. U-bend specimens made of unalloyed steel were not damaged in form of stress corrosion cracking in all test fuels at this test temperature.
Ziel dieser Untersuchungen war die Bewertung der Beständigkeit häufig eingesetzter Dichtungswerkstoffe, wie Fluorkautschuk (FKM), Fluorsiliconkautschuk (FVMQ), Siliconkautschuk (VMQ), Ethylen-Propylen-Dien-Kautschuk (EPDM), Chloroprenkautschuk (CR), chlorsulfoniertes Polyethylen (CR), Butylkautschuk (IIR), Acrylnitril-Butadien-Kautschuk (NBR), Polyes-terurethankautschuk (PUR) und Polyamid (PA) in Kraftstoffen und Heizöl mit und ohne bioge-ne Zusätze bei 20 °C, 40 °C und 70 °C. E10 (Kraftstoff mit max. 10 % Ethanol), E85 (Kraftstoff mit 85 % Ethanol), Dieselkraftstoff mit max. 5 % Biodiesel, Super mit max. 5 % Ethanol, un-gealtertes und gealtertes B10 (Heizöl mit 10 % Biodiesel) sowie zum Vergleich reiner Dieselkraftstoff, Heizöl und Kraftstoff Super plus zählten zu den Testsubstanzen.
Masse, Zugfestigkeit und Bruchdehnung wurden von den Prüfkörpern vor und nach der 84-tägigen Auslagerung in den Kraftstoffen und Heizöl bestimmt. Die visuelle Begutachtung einiger Elastomerprüfkörper zeigte eindeutig die hohe Quellung bis zur partiellen Auflösung.
Die Shore-Härte A und D (für PA) der Prüfkörper wurden vor und nach der 42-tägigen Auslagerung in den Kraftstoffen bestimmt.
In den internationalen Normen wird zur Bewertung der Beständigkeit von Elastomeren kein Grenzwert der Reduzierung der Zugeigenschaften und der Shore-Härte definiert. Deshalb wurde für die Beständigkeitsbewertung ein Grenzwert von 15 % festgelegt. Zusammenfassend kann die Aussage getroffen werden, dass die Beständigkeit der Fluorpolymere FKM und FVMQ in den Kraftstoffen und Heizöl mit und ohne biogene Zusätze die beste ist.
Die BAM-Liste - Anforderungen an Tanks für die Beförderung gefährlicher Güter – mit den Beständigkeitsbewertungen metallischer und polymerer Werkstoffe ist Grundlage für die stoffbezogenen Baumusterzulassungen für Tankcontainer und ortsbewegliche Tanks zur Beförderung gefährlicher Güter durch die BAM seit der Herausgabe der 1. Auflage 1989. Diese Beständigkeitsbewertungen werden nicht nur bundesweit, sondern weltweit als Erkenntnisquelle genutzt. Für die Zulassung von Kesselwagen und Tankfahrzeugen werden diese Daten auch herangezogen. Die Werkstoffbeständigkeitsdaten und der damit verbundene Informationsservice der BAM haben mit Sicherheit dazu beigetragen, Leckagen von Tanks aufgrund des Einsatzes von Tanks/Kesselwagen aus einem gegenüber dem Füllgut unbeständigem Tankwerkstoff oder Dichtungswerkstoff zu vermeiden.
Seitens der Industrie besteht großes Interesse, Polyethylenterephthalat (PET) als Werkstoff für Verpackungen zum Transport von Gefahrgütern einzusetzen, da aufgrund der hohen Festigkeit und Steifigkeit von PET die Wanddicken und somit die Kosten der Verpackungen reduziert werden können. Die Prüfung der Spannungsrissbeständigkeit von Polyethylenformstoffen als Werkstoffe von Verpackungen erfolgt mit Labormethoden unter Verwendung einer Standardflüssigkeit als Prüfmedium für die Spannungsrisse auslösende Wirkung auf Polyethylen (PE), wodurch Zeit und Kosten der Prüfungen reduziert werden.
Ziel dieser Arbeit war es, eine Laborprüfmethode zum Vergleich der Spannungsrissbeständigkeit von PE und PET auf ihre Anwendbarkeit zu prüfen, wie z.B. den Full Notch Creep Test (FNCT). Es wurde untersucht, ob die Prüfkörper aus PE und PET mit umlaufender Kerbe in dieser durch die chemische Industrie entwickelten und von der BAM konzipierten Apparatur auf der Basis des FNCT zu messbaren Ergebnissen unter Einfluss eines Ölsäureamidethoxylates als Netzmittel bei 50 °C führen.
Die Testergebnisse bestätigten die Eignung des Prüfverfahrens für die acht eingesetzten Formstoffe aus PE. Dieses Prüfverfahren konnte nicht für PET angewandt werden, da die Prüfkörper aufgrund der hohen Festigkeit und Steifigkeit des PET beim Kerbvorgang zerbrachen. Die gleiche Aussage konnte für den Nachweis der der Spannungsrissbeständigkeit von Verpackungen, der in der BAM Gefahrgutregel BAM-GGR 015 beschrieben wird, getroffen werden. Die einzige Möglichkeit zum Nachweis der Spannungsrissbeständigkeit von PET besteht in der Durchführung von Stapeldruckprüfungen.
Plastic storage tanks for heating oil have been on the market since the early 1970s in Germany, mainly made from polyethylene grades. Tank manufacturers and experts examining the tanks recommend the replacement of the tanks to ensure the safety after a period of 30 years. The tank manufacturer is legally obliged to specify the service life of the tanks.
Polyethylene is subject to ageing by alteration of the properties during its life cycle. A distinction is made between internal and external ageing processes. The internal ageing, such as the breakdown of internal stresses, post-crystallization, phase sepa-ration of multicomponent systems and plasticizer migration is attributed to thermodynamically instable conditions of the plastic material. The external ageing in form of stress cracking, fatigue cracking, thermooxidative degradation or swelling is based on physical or chemical effects of the environment of the polyethylene grade. The degree of ageing and the nature of the degradation process mainly depend on the chemical degradation of the polyethylene, the wall thickness of the tank and the environmental conditions. There are no results available on the long-term behaviour of the polyethylene grades used as materials for heating oil storage tanks, especially after a service life of more than 25 years.
The aim of this investigation was the determination of the factual degree of damage in comparison to the uncontaminated polyethylene grades. Data on the melt flow rate (MFR) and density of the used polyethylene grades are available because the BAM was the competent authority for the approval of the plastic heating oil storage tanks until the end of the 1980s.
The technical service of specialist companies for fuel tank disposal supplied tank sections from the bottom, the shell and the roof of 8 segregated heating oil storage tanks. Some of the tanks had been in service for more than 30 years. Two polyethylene grades mainly were used as materials for these tanks over this time. The determination of the MFR according to EN ISO 1133 and the FTIR spectroscopy followed standard test methods.
The highest average percentage increase in the MFR was determined as 31- 43 % for the bottom section of the tanks, for both the inner shell and the outer shell. The lowest increase in MFR was measured for the top of the tank, with 6 - 12 % for the inner shell and 0 - 8 % for the outer shell. The tank shell sections had an average percentage increase in MFR of 10 - 33 % for the inner shell and of 14 - 40 % for the outer shell.
The oxidative damage of the polyethylene grades was highest in the bottom area due to the permanent contact with the heating oil and degradation products.
The microtome cuttings were analyzed with image-guided infrared microscopy in the transmission mode and confirmed the results obtained with the MFR measurements.
In summary it can be concluded that the oxidative damage of the polyethylene grades after long-term contact with heating oil is relative low.