5 Werkstofftechnik
Filtern
Dokumenttyp
- Vortrag (431)
Sprache
- Englisch (332)
- Deutsch (96)
- Mehrsprachig (3)
Referierte Publikation
- nein (431) (entfernen)
Schlagworte
- Additive Manufacturing (38)
- Additive manufacturing (24)
- Microstructure (21)
- Corrosion (20)
- Glass (18)
- Ontology (17)
- Fatigue (13)
- Ceramics (12)
- LCF (11)
- 316L (10)
- Additive Fertigung (10)
- Creep (10)
- Ontologie (10)
- Transmission electron microscopy (10)
- Crack growth (9)
- Fraktographie (9)
- Sintering (9)
- Ceramic (8)
- Thermoelectrics (8)
- Diffraction (7)
- Fractography (7)
- Machine Learning (7)
- Particle size (7)
- Powder (7)
- Ti-6Al-4V (7)
- CCUS (6)
- DCB (6)
- Digitalisierung (6)
- EBSD (6)
- Glas (6)
- High entropy alloys (6)
- Low Cycle Fatigue (6)
- Mikrostruktur (6)
- Scanning electron microscopy (6)
- Zugversuch (6)
- 3D printing (5)
- AGIL (5)
- Aluminium (5)
- Anisotropy (5)
- Crystal plasticity (5)
- Crystallization (5)
- Glass fiber reinforced polymers (5)
- In situ (5)
- Microgravity (5)
- Oxidation (5)
- Slurry (5)
- VSSA (5)
- Water speciation (5)
- AISI 316L (4)
- Alloy 2618A (4)
- CALPHAD (4)
- CCS (4)
- CO2 (4)
- Coarsening (4)
- Creep behavior (4)
- Degradation (4)
- Droplet corrosion (4)
- EN AW-2618A (4)
- FAIR (4)
- FAIR data management (4)
- Fatigue crack growth (4)
- Fe-Al alloys (4)
- Foaming (4)
- High-temperature corrosion (4)
- In-space manufacturing (4)
- Intermetallics (4)
- Iron aluminides (4)
- Kriechen (4)
- Laser powder bed fusion (4)
- Layerwise slurry deposition (4)
- Martensitic steel (4)
- Mechanical properties (4)
- Nano (4)
- Nano powder (4)
- Neutron diffraction (4)
- Nickel-base superalloys (4)
- Non-destructive testing (4)
- Normung (4)
- Plattform MaterialDigital (4)
- Polymer matrix composites (4)
- Residual Stress (4)
- Semantic Web Technologies (4)
- Sulfidation (4)
- Supercritical/dense phase CO2 (4)
- TMF (4)
- Thermomechanical fatigue (4)
- Vickers (4)
- Wissensrepräsentation (4)
- Alkali ions (3)
- Alumina (3)
- Aluminium Alloy (3)
- Aluminium alloy (3)
- Betriebsfestigkeit (3)
- CCU (3)
- Carbon steels (3)
- Ceramic spring (3)
- Computed Tomography (3)
- Dielectric strength (3)
- Fracture surface (3)
- Full Notch Creep Test (3)
- Gassensorik (3)
- Geothermal (3)
- H2Safety@BAM (3)
- Heat treatment (3)
- High temperature corrosion (3)
- Keramik (3)
- Knowledge graph and ontologies (3)
- Lebensdauer (3)
- Mechanical behavior (3)
- Mechanical testing (3)
- Mikroplastik (3)
- Ni-Resist (3)
- PMD (3)
- Residual stress (3)
- S-phase (3)
- SEM (3)
- Scarf repairs (3)
- Semantic Interoperability (3)
- Silicate Glasses (3)
- Soda-lime silicate glass (3)
- Superaustenite steel (3)
- Tensile Test (3)
- Texture (3)
- Transmission electron microscopy (TEM) (3)
- Wasser (3)
- Water content (3)
- Welding (3)
- Wind turbine blades (3)
- X-ray diffraction (3)
- Zerstörungsfreie Prüfung (3)
- μ-gravity (3)
- Advanced ceramics (2)
- Alkali zinc borate glasses (2)
- Alterung (2)
- Analytische Zentrifuge (2)
- Bildanalyse (2)
- CLS (2)
- CO2 quality (2)
- CT (2)
- Calciumcobaltit (2)
- Calciummanganat (2)
- Carbon capture (2)
- Carbon capture storage (2)
- Carbon dioxide (2)
- Carbon steel (2)
- Characterization (2)
- Chemically complex alloy (2)
- Composite (2)
- Composites (2)
- Concrete (2)
- Copper (2)
- Crack tip opening displacement (2)
- Creep data (2)
- Dark-field transmission electron microscopy (2)
- Data Fusion (2)
- Data Interoperability (2)
- Data mapping (2)
- Datenbank (2)
- Dielectric breakdown (2)
- Diesel (2)
- Diffraction Elastic Constants (2)
- Diffusion (2)
- Digital image correlation (2)
- Digitaler Zwilling (2)
- Digitalization (2)
- Digitization (2)
- Digtial Representation (2)
- Diopside (2)
- Dislocation (2)
- EDXRD (2)
- Electron microscopy (2)
- Electron-beam-induced modification (2)
- Electronic Lab Notebook (2)
- Environmental Stress Cracking (2)
- Environmental stress cracking (2)
- Faser-Kunststoff-Verbunde (2)
- Faserkunststoffverbunde (2)
- Faseroptische Sensorik (2)
- Ferritic-martensitic steels (2)
- Fracture Toughness (2)
- Full-Notch Creep Test (FNCT) (2)
- Geführte Ultraschallwellen (2)
- Gitterkonstanten (2)
- Glass-ceramics (2)
- Hard machining (2)
- High Cycle Fatigue (2)
- High Entropy Alloy (2)
- High Temperature Corrosion (2)
- High temperature (2)
- High temperature mechanical properties (2)
- High-entropy alloy (2)
- High-entropy alloys (2)
- Hochentropie-Legierung (2)
- Hochtemperatur (2)
- Impurities (2)
- In-situ (2)
- Interoperability (2)
- Joined nickel-based alloys (2)
- L-PBF (2)
- Laser (2)
- Laser Powder Bed Fusion (2)
- Laser Powder Bed fusion (2)
- Laser beam melting (2)
- Layerwise (2)
- Leckdetektion (2)
- Lunar regolith simulant (2)
- ML (2)
- Material Digital (2)
- Material digital (2)
- Metrologie zur Wasserstoffspeicherung (2)
- Microplastics (2)
- Microstrucrue Design (2)
- Microstructural analysis (2)
- Microstructure Design (2)
- Mixed gas atmosphere (2)
- Modeling (2)
- Multilayer (2)
- Multilayer technology (2)
- Multilayertechnik (2)
- NDT (2)
- Nano particle (2)
- Nano screening (2)
- Nano-powder (2)
- Nanomaterial (2)
- Nanoparticles (2)
- Nanopulver (2)
- Notches (2)
- OECD TG 124 (2)
- Ontologien (2)
- Ontology development (2)
- Orientation (2)
- Oriented surface crystallization (2)
- Oxidation behavior (2)
- Oxide Glasses (2)
- Oxidglas (2)
- PBF-LB/M/316L (2)
- PE-HD (2)
- PMD Core Ontology (2)
- PMDco (2)
- Partikelgrößenverteilung (2)
- Phase-field simulation (2)
- Phasenidentifikation (2)
- Pipeline (2)
- Plattform Material Digital (2)
- Polyethylen (2)
- Polyethylen hoher Dichte (2)
- Polymer Matrix Composites (2)
- Process monitoring (2)
- Push-out Test (2)
- REM (2)
- Reaction sintering (2)
- Residual Stresses (2)
- Ressidual stress (2)
- Rotor blade (2)
- Sandwich (2)
- Scale-bridging (2)
- Schadensanalyse (2)
- Schädigung (2)
- Selective Laser Melting (2)
- Semantic Representation (2)
- Semantic Web (2)
- Semantisches Web (2)
- SensRef (2)
- Silicon Carbide (2)
- Silver diffusion (2)
- Silver-glass-metallization-paste (2)
- Simulation (2)
- Sinter additive (2)
- Sintering additives (2)
- Sintern (2)
- Spannungsriss (2)
- Spectroscopy (2)
- Spray drying (2)
- Spring constant (2)
- Standard (2)
- Standardisierung (2)
- Standardization (2)
- Structural Health Monitoring (SHM) (2)
- Superlegierung (2)
- Surface energy (2)
- TED-GC-MS (2)
- TEM (2)
- Tensile Test Ontology (2)
- Tensile data (2)
- Tensile test (2)
- Thermo-Mechanical Fatigue (2)
- Thermoelectric (2)
- Ti64 (2)
- TiAl5V4 (2)
- Titan (2)
- Topographie (2)
- Topography (2)
- UV-irradiation (2)
- Ultrasound (2)
- Virtual experiments (2)
- Viscoplasticity (2)
- Viscosity (2)
- Wall thickness (2)
- Wind turbine blade shells (2)
- Windenergie (2)
- XANES (2)
- XRD (2)
- Zero-g (2)
- Zugeigenschaften (2)
- robotische Glasschmelzanlage (2)
- µ-gravity (2)
- 3D (1)
- 3D Druck (1)
- 3D REM (1)
- 3D Reconstruction (1)
- 3D glass structure model (1)
- 3D materialography (1)
- 3D-printing (1)
- 9-12% Cr ferritic-martensitic steels (1)
- 9–12%Cr steel (1)
- AFM based test methods (1)
- AM (1)
- Accelerated integration scheme (1)
- Acids (1)
- Active thermography (1)
- Additiv gefertigter Stahl (1)
- Adiabatic shear bands (1)
- Advanced manufacturing (1)
- Aerospace (1)
- Age hardening (1)
- Ageing (1)
- Agglomerates (1)
- Aggressive gases (1)
- Aging (1)
- Air-coupled ultrasonic testing (1)
- Airborne ultrasonic testing (1)
- Al-Li alloys (1)
- Alkali zinc borate glass (1)
- Aluminum (1)
- Aluminum alloys (1)
- Analyse (1)
- Analysis (1)
- Analytik (1)
- Annealing (1)
- Atmospheric plasma spraying (1)
- Aussonderugnsrate (1)
- Austenitic cast iron (1)
- Austenitic steel 316L (1)
- Automatable digital approach (1)
- Automation (1)
- BET (1)
- Biaxial strength (1)
- Binder jetting (1)
- Bioactive (1)
- Bioactive Glass (1)
- Bioceramics (1)
- Biodiesel (1)
- Blähen (1)
- Bond energy (1)
- Breakdown strength (1)
- Brinell hardness (1)
- Bruchflächen (1)
- Bruchflächenanalyse (1)
- Bruchflächenauswertung (1)
- Bundesoberbehörden (1)
- CFK (1)
- CO2-corrosion (1)
- Calcination (1)
- Calcium cobaltite (1)
- Calcium manganate (1)
- Calcium sulfates (1)
- Calibration (1)
- Cantor alloy (1)
- Capture (1)
- Carbon (1)
- Carbon steels (1)
- Carbon Capture (1)
- Carbon Capture, Utilization and Storage (CCUS) (1)
- Carbon Fiber Reinforced Plastics (1)
- Carbon Fibers (1)
- Casting (1)
- Centrifugal casting (1)
- Ceramic multilayer (1)
- Ceramic springs (1)
- Certification Standard 22 (1)
- Certified Referencematerial (1)
- Cetrifugal Liquid Sedimentation CLS (1)
- Chemically complex alloys (1)
- Chemo-mechanical coupling (1)
- Chromatography (1)
- Chromia (1)
- Chromium oxide (1)
- Co-firing (1)
- Co-segregation (1)
- Coatings (1)
- Complex borides (1)
- Complex loading (1)
- Component assessment (1)
- Composite testing (1)
- Compositionally complex alloys (1)
- Computed tomography (1)
- Condensation (1)
- Contamination (1)
- Continnum damage model (1)
- Cooling simulations (1)
- Cow stress (1)
- Cr2O3 (1)
- Crack (1)
- Crack Propagation (1)
- Crack evolution (1)
- Crack propagation (1)
- Creep anisotropy (1)
- Creep behaviour (1)
- Creep-Fatigue (1)
- Creep-fatigue (1)
- Crevice corrosion (1)
- Cross linking (1)
- Crystal Defects (1)
- Crystal Orientation (1)
- Crystal Plasticity Modelling (1)
- Cubical Iron Oxide (1)
- Cure process (1)
- Cycle jump (1)
- Cyclic R-Curve (1)
- Cyclic oxidation (1)
- Cyclic softening (1)
- DIN (1)
- DLS (1)
- Damage (1)
- Damage Behavior (1)
- Damage Tolerance (1)
- Damage behavior (1)
- Damage mechanisms (1)
- Dark-field transmission electron microscopy (DFTEM) (1)
- Data Exchange (1)
- Data Management (1)
- Data Structures (1)
- Data linking (1)
- Data management (1)
- Data pipeline concept (1)
- Data space (1)
- Data storage (1)
- Data structure (1)
- Datenökosystem (1)
- Deep learning (1)
- Defects (1)
- Defects phase diagram (1)
- Defects thermodynamics (1)
- Deformation behavior (1)
- Dehnungsfehler (1)
- Density (1)
- Density-based Thermodynamics (1)
- Density-based model (1)
- Density-based phase-field modelling (1)
- Dental (1)
- Destabilization (1)
- Die casting (1)
- Dielectric breakdown strength (1)
- Dielectric characterization (1)
- Diffraction Enhanced Imaging (1)
- Diffraction contrast (1)
- Diffusion coefficient (1)
- Digital representation (1)
- Digital workflow (1)
- Dislocation substructure (1)
- Dislocations (1)
- Disordered assemblies (1)
- Dispersion process (1)
- Dissimilar metal weld (1)
- Dissolved water (1)
- Distribution function (1)
- Driving physical mechanism (1)
- Dual-energy (1)
- Durchschlagfestigkeit (1)
- Dynamic mechanical analysis (1)
- Dynamic mechanical analysis (DMA) (1)
- Dynamisch Mechanische Analyse (1)
- EAC-1A (1)
- EASA (1)
- EDX (1)
- EN AW 2618A (1)
- Early oxidation (1)
- Eigenspannung (1)
- Elastic constants (1)
- Electric field distribution (1)
- Electric field strength (1)
- Electrical insulation (1)
- Electron Backscatter Diffraction (1)
- Electron Microscopy (1)
- Electron backscatter diffraction (1)
- Electron backscattered diffraction (EBSD) (1)
- Elektronisches Laborbuch (ELN) (1)
- Energy harvesting (1)
- Entwicklung (1)
- Environmental Stress Cracking (ESC) (1)
- Ermüdung (1)
- Ermüdungsriss (1)
- Erneuerbare Energien (1)
- Etching (1)
- Extensometer (1)
- FAIR Data Management (1)
- FAIR data (1)
- FCH JU (1)
- FIB (1)
- Fabrication method (1)
- Fahrrad (1)
- Failure test (1)
- Faser (1)
- Faseroptik (1)
- Faserverstärkte Kunstoffe (1)
- Fatigue Crack Growth (1)
- Fatigue Life Evaluation (1)
- Fatigue damage (1)
- Fatigue fracture (1)
- Fatigue of sandwich shell structures (1)
- Fatigue of sandwich structures (1)
- Fatigue performance (1)
- FeCr- alloys (1)
- Federkonstante (1)
- Feldspar (1)
- Fem (1)
- Ferritic Alloys (1)
- Ferroelectret (1)
- Ferroelektret (1)
- Fertigungstechnologie (1)
- Festigkeit (1)
- Fiber (1)
- Fiber reinforced polymer (1)
- Fiber reinforced polymers (1)
- Fine Powder (1)
- Finite element analysis (1)
- Finite elmenet simulation (1)
- Flowability (1)
- Fluorescence spectroscopy (1)
- Focused Ion Beam (1)
- Foliengießen (1)
- Force-distance diagram (1)
- Formerkennung (1)
- Fracture Mechanics (1)
- Fracture Surface Analysis (1)
- Fracture behavior (1)
- Fracture surface analysis (1)
- Fracture toughness (1)
- Freeze Drying (1)
- GC-MS (1)
- GD-OES (1)
- Gas storage (1)
- Gasabgabe (1)
- Gasgehalt (1)
- Gasturbinen (1)
- Gefüge (1)
- General Aviation (1)
- Geopolymers (1)
- Gitterfehlpassung (1)
- Glasmatrixkomposit (1)
- Glass Fibres (1)
- Glass composition (1)
- Glass fibre reinforced plastics (1)
- Glass melting (1)
- Glass powder (1)
- Glass screening device (1)
- Gold nanoparticle synthesis (1)
- Gold nanoparticles (1)
- Gradient-enhanced damage (1)
- Grain boundaries (1)
- Grain boundary engineering (1)
- Granules (1)
- Granulometrie (1)
- Graphic design (1)
- Grünfolieneigenschaften (1)
- HDPE Soprption (1)
- HEA (1)
- HIP (1)
- Hardness (1)
- Hartbearbeitung (1)
- Heat Treatment (1)
- Heat Treatments (1)
- Heißgasextraktion (1)
- Heißgaskorrosion (1)
- High Entropy Alloys (1)
- High Temperature Testing (1)
- High entropy alloy (1)
- High entropy superalloys (1)
- High-Temperature Corrosion (1)
- High-density polyethylene (1)
- Hochentropielegierungen (1)
- Hochspannungsprüfung (1)
- Hochtemperaturbrennstoffzelle (1)
- Hochtemperaturermüdung (1)
- Horizon 2020 (1)
- Hot Press (1)
- Hot isostatic pressing (1)
- Hot pressing (1)
- Hydrogen (1)
- Hydrogen permeation (1)
- Hydrogen sensor (1)
- Hydrogen sensors (1)
- Hyper-arid (1)
- IN 718 (1)
- IN738LC (1)
- IR (1)
- ISRU (1)
- Implant failures (1)
- Implants (1)
- In situ tensile test (1)
- In-Situ Testing (1)
- Inconel 686 coating (1)
- Inconel 718 (1)
- Infrastructure (1)
- Initial attachment (1)
- Injection (1)
- Interface (1)
- Interface Strength (1)
- Interfacial Spinodal (1)
- Internal friction (1)
- Inverse ostwald ripening (1)
- Investment casting (1)
- Iron oxide nanoparticles (1)
- Kalzinierung (1)
- Kavitation (1)
- Kennwertermittlung (1)
- Keramikfeder (1)
- Keramische Folien (1)
- Klebung (1)
- Kleinprobenprüfung (1)
- Knowledge Graphs (1)
- Knowledge Representation (1)
- Knowledge graph (1)
- Kontrastierung (1)
- Korrosion (1)
- Kriechversuche (1)
- Kristallisation (1)
- Kunststoffe (1)
- Kupfer (1)
- Kurzzeitfestigkeit (1)
- L-PBF 316L (1)
- LSD-print (1)
- LTCC (1)
- Laminography (1)
- Laser Poeder Bed Fusion (1)
- Laser Scanning Microscopy (LSM) (1)
- Laser cladding (1)
- Laser curing (1)
- Laser induced slipcasting (1)
- Laserbearbeitung (1)
- Laserscanningmikroskopie (LSM) (1)
- Lattice misfit (1)
- Layer depostion (1)
- Layer system (1)
- Layerwise Slurry Deposition (1)
- Legierung mit komplexer Zusammensetzung (1)
- Li-ion battery (1)
- Life cycle (1)
- Lightweight materials (1)
- Lightweighting (1)
- Lithium Ion Batteries (1)
- Localized plasmons (1)
- Long-term storage (1)
- Low cycle fatigue (1)
- Low-Cycle-Fatigue (1)
- Low-cycle-fatigue behaviour (1)
- Luftultraschall (1)
- Lunar habitat (1)
- Lösungsmittel (1)
- MEA (1)
- Manganese oxide (1)
- Manufacturing (1)
- Martensitic steel (1)
- Mat-o-lab (1)
- Material Life Cycle (1)
- Material defects (1)
- MaterialDigital (1)
- Materialcharakterisierung (1)
- Materialentwicklung (1)
- Materialmodell (1)
- Materials Data Space (1)
- Materials Modelling (1)
- Materials Science (1)
- Materials and Processes Data Reusability (1)
- Materials science (1)
- Materials testing (1)
- Materialwissenschaft (1)
- Matrix (1)
- Mechanical and thermal testing (1)
- Mechanische Eigenschaften (1)
- Mechanisches Verhalten (1)
- Mechanistic Modelling (1)
- Medium Entropy Alloys (1)
- Medium entopy alloy (1)
- Medium-entropy alloy (1)
- Melt pool boundary (1)
- Metadata schema (1)
- Metallic components (1)
- Metallic silver precipitates (1)
- Metallography (1)
- Metrologie (1)
- Micro-shrinkages (1)
- Microbiologically influenced corrosion (1)
- Microhardness (1)
- Micromechanical model (1)
- Microstructural characterization (1)
- Microstructural evolution (1)
- Microstructural orientation (1)
- Microstructure Characterization (1)
- Microstructure Evolution (1)
- Microstructure characterisation (1)
- Microstructure design (1)
- Microstructure evolution (1)
- Microstructure modification (1)
- Microstructure-property-correlation (1)
- Mid-Level Ontology for MSE (1)
- Mikro-Computertomographie (1)
- Mikrogravitation (1)
- Mikrostrukturentwicklung (1)
- Mindedestberstdruck (1)
- Mixed Ca-K-Na phosphates (1)
- Mn3O4 (1)
- Modell (1)
- Monte-Carlo Simulation (1)
- Mortar (1)
- Mortel (1)
- Multi-principal element alloys (1)
- Multiaxial stress state (1)
- NTE (1)
- Na and K rhenanites (1)
- Nano material (1)
- Nano-assemblies (1)
- Nanoparticle synthesis (1)
- Nanopartikel (1)
- Nanoplattform (1)
- Negative charged microparticle (1)
- Neutron Diffraction (1)
- New standards (1)
- Nickel-base superalloy (1)
- Non-desired foaming (1)
- Nondestructive testing (1)
- Nucleation (1)
- Nucleation mode (1)
- OECD TG (1)
- Oberflächenaktive wässrige Medien (1)
- Online quality control (1)
- Ontologies (1)
- Ooxidation (1)
- Optic (1)
- Overaging (1)
- Oxide glass (1)
- P92 (1)
- P92 steels (1)
- PA6.6 (1)
- PPA (1)
- Parametric modeling (1)
- Particle size determination (1)
- Partikelgröße (1)
- Patent (1)
- Paving (1)
- Phase Diagrams (1)
- Phase Separation (1)
- Phase analysis (1)
- Phase diagram (1)
- Phase field simulation (1)
- Phase separation (1)
- Phase transformation (1)
- Phase transformations (1)
- Phase-Field Simulation (1)
- Phase-Field Simulations (1)
- Phase-field Simulation (1)
- Photon counting detector (1)
- Physically based material model (1)
- Physics-informed Neural Network (1)
- Pipeline network (1)
- Planetary surface (1)
- Platform Material Digital (1)
- Platform Material Digital (PMD) (1)
- Platform MaterialDigital (1)
- Platform MaterialDigital (PMD) (1)
- Plattform Material Digital (PMD) (1)
- Pole figures (1)
- Polyaniline (1)
- Polyethylene, PE-HD (1)
- Polymer (1)
- Polymer Matrix Composite (1)
- Polymerwissenschaften (1)
- Porcelain (1)
- Pores (1)
- Powder deposition (1)
- Power plant (1)
- Precipitates (1)
- Precipitation (1)
- Precipitation Analysis (1)
- Precipitation hardening (1)
- Preparation (1)
- Pressure assisted sintering (1)
- Pressure-assisted sintering (1)
- Probengrößeneffekt (1)
- Protective coating (1)
- Präparation (1)
- Pull-out (1)
- Pycnometry (1)
- Quantitative Precipitation Analysis (1)
- Quantitative image analysis (1)
- Rafting (1)
- Recommendations (1)
- Recycling (1)
- Reference data (1)
- Reference material (1)
- Referenzdaten (1)
- Refractory chemically complex alloy (1)
- Refractory chemically complex alloys (1)
- Regelwerke (1)
- Relaxation (1)
- Relaxation metallic glasses (1)
- Relaxationsphänomene (1)
- Repair of sandwich shell structures (1)
- Reproducibility (1)
- Research Data Management (1)
- Residual stress analysis (1)
- Residual stresses (1)
- Resistance (1)
- Restberstfestigkeit (1)
- Review (1)
- Rissentwicklung (1)
- Rissheilung (1)
- Risswachstum (1)
- Roboter (1)
- Robotic melting (1)
- Robotische Schmelzanlage (1)
- Rotorblattschalen (1)
- Roughness (1)
- Röntgen-Refraktion (1)
- Röntgenbeugung (1)
- Röntgenrefraktion (1)
- S355 steel sheet (1)
- SHM (1)
- SIMS (1)
- SLM (1)
- Safety assessment (1)
- Sailplane Development Panel (1)
- Salzschmelzen (1)
- Sample preparation (1)
- Sandwich structures (1)
- Scanning Electron Microscopy (SEM) (1)
- Scanning electron microscope (1)
- Scanning transmission electron microscopy (STEM) (1)
- Scarf joint repair (1)
- Schadensprävention (1)
- Schwerelosigkeit (1)
- Schwingbrüche (1)
- Schwingstreifen (1)
- Screen printing (1)
- Selective laser melting (1)
- Semantic Data (1)
- Semantic Interioerability (1)
- Semantic structuring (1)
- Semantic web (1)
- Semiconductor materials (1)
- Sensor (1)
- SiO2 (1)
- Sibayak (1)
- Silber (1)
- Silicatglas (1)
- Silver cluster (1)
- Silver metallization paste (1)
- Silver precipitates (1)
- Silver-glass metallization paste (1)
- Simulation of concrete (1)
- Single-Crystal (1)
- Single-crystals (1)
- Sintering atmosphere (1)
- Sintertemperatur (1)
- Sinterung (1)
- Size distribution (1)
- Slow Crack Growth (SCG) (1)
- Slow crack growth (1)
- Small-Angle X-ray Scattering (1)
- Soda-lime-silica glass (1)
- Sol-gel coating (1)
- Solar sintering (1)
- Solid solution strengthening (1)
- Space exploration (1)
- Spannungs-Dehnungs-Verhalten (1)
- Spark plasma sintering (1)
- Specific surface (1)
- Spezifische Oberfläche (1)
- Spinodal Decomposition (1)
- Split Hopkinson bar (1)
- Spring constant (1)
- Stainless steel (1)
- Stanzen (1)
- Steel (1)
- Storage (1)
- Strain rate dependence (1)
- Structure (1)
- Structured heating (1)
- Struktur (1)
- Subsurface defects (1)
- Sulfiding (1)
- Superalloy (1)
- Superalloy single crystals (1)
- Superalloys (1)
- Superaustenite steel (1)
- Supercritical/dense phase CO 2 (1)
- Superlegierungen (1)
- Surface (1)
- Surface Energy (1)
- Surface Nucleation (1)
- Surface crystallization (1)
- Surface nucleation (1)
- Symbolik (1)
- Symmetric dwell periods (1)
- Synchrotron CT (1)
- Synchrotron radiation (1)
- Synchrotronstrahlung (1)
- Syngle Crystal alloy (1)
- Synthetic air (1)
- Systematische Schadensanalysen, Prozeduren (1)
- TAHYA (1)
- TED (1)
- TMF experiments (1)
- Temperature (1)
- Temperature driven process (1)
- Temperaturschwankungen (1)
- Tempered Martensite Ferritic Steels (1)
- Tempered martensite ferritic steel (1)
- Tempered martensite ferritic steels (1)
- Tensile Properties (1)
- Tensile stress relaxation (1)
- Tensile testing (1)
- Texturation (1)
- Thermal degradation (1)
- Thermal stress (1)
- Thermische Analyse (1)
- Thermo mechanical fatigue (1)
- Thermo-mechanical fatigue (1)
- Thermo-mechanical-loading (1)
- Thermo-optical measurement (1)
- Thermoanalytical Methods (1)
- Thermoelectric generator (1)
- Thermoelectric oxide (1)
- Thermoelektrika (1)
- Thermoelektrischer Generator (1)
- Thermographie (1)
- Thermogravimetric analysis (1)
- Thermogravimetry (1)
- Thermomechanics (1)
- Thermomechanik (1)
- Thermomechanische Eigenschaften (1)
- Thermoset polymers (1)
- Thesaurus (1)
- Titanium (1)
- Tomography (1)
- Tools (1)
- Transmissionselektronenmikroskopie (1)
- Transparent ceramics (1)
- Two Photon Polymerization (1)
- Ultraschall (1)
- Umgebungsbedingter Spannungsriss (1)
- Under cyclic loading (1)
- Utilization (1)
- Utilization, and storage (CCUS) technology (1)
- VCSEL (1)
- Vacuum hot extraction (1)
- Vernetzung (1)
- Versetzungsstrukturen (1)
- Vickers hardness (1)
- Virtueller Materialdatenraum (1)
- Viscose sintering (1)
- Viskoplastisch (1)
- Wandler (1)
- Waste water (1)
- Water-based (1)
- Weibull Distribution (1)
- Weibull distribution (1)
- Welding processing influences (1)
- Werkstoffdaten (1)
- Werkstoffprüfung (1)
- Whole-chain CCS scenario (1)
- Wind energy (1)
- Wind turbine (1)
- Wind turbine blade shell structures (1)
- Withstand voltage tests (1)
- Workshop (1)
- Wärmespeicher (1)
- X-Ray Diffraction (1)
- X-ray imaging (1)
- X-ray laminography (1)
- X-ray refraction (1)
- XRM (1)
- Zugversuchsontologie (1)
- Zyklische Belastung (1)
- Zyklische R-Kurve (1)
- alumina (1)
- arbon capture (1)
- carbon steel (1)
- ceramic (1)
- ceramics (1)
- condensate (1)
- corrosion (1)
- dental (1)
- dispersion (1)
- electrochemical characterization (1)
- impurities (1)
- microstructure analysis (1)
- multi scale testing (1)
- particle size determination (1)
- pitting corrosion (1)
- sample preparation (1)
- selective laser melting (1)
- thermomechanische Beanspruchung (1)
- utilization, and storage (CCUS) technology (1)
- volume resistivity (1)
- zertifizierte Referenzmaterialien (1)
- Öffentliche Sicherheit (1)
- Überblick (1)
Organisationseinheit der BAM
- 5 Werkstofftechnik (431)
- 5.2 Metallische Hochtemperaturwerkstoffe (115)
- 5.1 Mikrostruktur Design und Degradation (112)
- 5.4 Multimateriale Fertigungsprozesse (101)
- 5.3 Polymere Verbundwerkstoffe (52)
- 5.6 Glas (51)
- 8 Zerstörungsfreie Prüfung (46)
- 5.5 Materialmodellierung (45)
- 9 Komponentensicherheit (44)
- 8.5 Röntgenbildgebung (35)
Eingeladener Vortrag
- nein (431) (entfernen)
Die Entwicklung digitaler Prozesse für die Materialwissenschaft und Werkstofftechnik muss naturgemäß auch die Charakterisierungsmethoden der Werkstoffprüfung abbilden, die oft durch eine hohe Komplexität gekennzeichnet sind. Als vorteilhaft erweist sich dabei der hohe Standardisierungsgrad, der sich z.B. in klaren Anforderungen an die eingesetzten Prüfmittel und festgelegten Vorgehensweisen ausdrückt. Diese können (und müssen) in entsprechenden digitalen Versuchsbeschreibungen abgebildet werden, wobei sich die klaren Datenstrukturen und Terminologien als vorteilhaft erweisen.
Porosity in single-crystal nickel-base superalloys is removed by hot isostatic pressing (HIP) at temperatures above gamma’-solvus where the material is very soft and ductile. For example, single-crystal nickel-base superalloy CMSX-4 is HIPed at temperature 1288 °C, which is slightly higher than the gamma’-solvus temperature of this alloy equal to about 1280 °C. It is assumed that pore shrinking during HIP is mostly due to dislocation creep. Such a modelling of HIP of CMSX-4 was started in our group on the base of results of creep tests of [001] single-crystals at 1288 °C [1]. However, it was found later [2] that the alloy CMSX-4 shows very strong creep anisotropy at 1288 °C. Therefore, for calibration of the creep law, creep tests of different orientations under different stress levels are required at the HIP temperature. This was the main task of present work. Single-crystals of CMSX-4 of axial orientations [001], [011], [123] and [111] were cast by VIAM Moscow and tested by BAM Berlin under creep conditions at 1288 °C and stress levels between 4 MPa and 16 MPa. At all stress levels, the creep rate increases by an order of magnitude when changing the orientation from [001] to [111] with [011] and [123] orientations in between. Such a character of creep anisotropy corresponds to the orientation dependence of the Schmid factor for octahedral glide.
The crystal viscoplasticity model developed in [1] was improved to better represent the time induced softening observed during creep. The creep tests for different stresses and orientations as well as pore closure were simulated. The results of pore closure simulation are compared with measurements of porosity decrease during Hiping.
Zur Bewältigung der Herausforderung bei der Digitalisierung von Materialien und Prozessen ist eine mit allen Stakeholdern konsistente Kontextualisierung von Materialdaten anzustreben, d.h. alle erforderlichen Informationen über den Zustand des Materials einschließlich produktions- und anwendungsbezogener Änderungen müssen über eine einheitliche, maschinenlesbare Beschreibung verfügbar gemacht werden. Dazu werden Wissensrepräsentationen und Konzeptualisierungen ermöglichende Ontologien verwendet. Erste Bemühungen in den beiden Projekten Plattform Material Digital und Materials-open-Laboratory führten zur Erstellung von Anwendungsontologien, die Prozesse und Testmethoden explizit beschreiben. Dabei wurde u.a. der Zugversuch an Metallen bei Raumtemperatur nach DIN EN ISO 6892-1 ontologisch beschrieben. Diese als Beispiel dienende Ontologieentwicklung wird in dieser Präsentation vorgestellt.
Tour de table - BAM
(2021)
Die „auffälligen großen Streifen“ sind von echten Schwingstreifen nur sehr schwer zu trennen, weil sie parallel zu den Schwingstreifen verlaufen und meistens ebenfalls nicht sehr groß sind. Die im Labor getesteten Proben zeigten, dass diese großen Streifen zusammen mit Verreibungen auftraten und „tire tracks“ („Reifenspuren“) verursachten. Dies wurde durch eine hochauflösende REM-Untersuchung bestätigt, die „tire tracks“ auf den „großen Streifen“ zeigte. Ein weiterer Hinweis ist die Änderung des R-Werts von -1 auf 0,1, was zu einer Bruchfläche ohne große Streifen und „tire tracks“ führt.
Die Analyse von Bruchflächen wird in der Schadensanalyse meist auf der Basis von Erfahrungswissen vorgenommen, welches aus vorliegenden Untersuchungen, eigenen Vergleichsversuchen und aus der Literatur stammt. Durch Vergleiche mit bereits vorliegenden Bildern werden qualitativ Bruchmechanismen ermittelt. Grundlage sind zumeist zweidimensionale Bilder aus licht- und elekt-ronenoptischen Verfahren. Quantitative Aussagen beziehen sich bislang beispielsweise auf makroskopische Anteile von Bruchmechanismen oder die Ausmessung von Schwingstreifen. In jüngerer Zeit gibt es vermehrt Ansätze, Computer-Algorithmen einzusetzen, die in der Lage sind, unterschiedlich strukturierte Bruchmerkmale zu finden und zu klassifizieren. Im hier vorgestellten IGF-Vorhaben „iFrakto“, IGF Vorhaben Nr.: 21477 N, werden licht- und elektronenoptisch Topographie-Bilder erzeugt und die gewonnenen 3D-Informationen zusammen mit den klassischen 2D-Bildern ausgewertet.
The lecture focuses on the mechanisms of non-desired gas bubble formation and foaming during the sintering of glass powder compacts. It is shown that foaming is driven by carbon gases and that carbonates, encapsulated in micropores or mechaniacally dissolved beneath the glass surface, provide the major foaming source.
Polyethylen hoher Dichte (PE-HD) ist ein weit verbreitetes Material für Transportbehälter, die oft für eine längere Nutzungsdauer vorgesehen sind. Insbesondere in diesem Fall können mikroskopische Schäden im Material auch weit unterhalb der Streckgrenze auftreten, die durch eine Spannungskonzentration verursacht werden, deren Ursprung in intrinsischen Materialfehlern oder äußeren Kratzern liegt. Mit fortschreitender Schädigung bilden sich Rissstrukturen, die von verstreckten Fibrillen aufgespannt werden, bis es zum Versagen dieser Fibrillen kommt und sich der Riss ausbreitet. Dieser Schadensmechanismus des langsamen Risswachstums kann durch eine Vielzahl von Umgebungsmedien beschleunigt werden und wird dann als "environmental stress cracking" (ESC) bezeichnet. Eine international normierte Methode zur Validierung der Spannungsrissbeständigkeit von PE-HD Materialien ist der „Full Notch Creep Test“ (FNCT).
Anhand von Bruchflächenauswertungen mittels Rasterelektronenmikroskopie und Laser-Scanning-Mikroskopie, werden die typischen Schädigungsstrukturen des ESC sichtbar. Die fibrillierten Strukturen des ESC auf der Bruchfläche von PE-HD ergeben sich besonders bei oberflächenaktiven wässrigen Umgebungsmedien. In Lösungsmittel-Umgebungsmedien, im Zusammenspiel mit PE-HD, kommt es aufgrund der plastifizierenden Wirkung zur Herabsetzung der Streckspannung und Bruchflächen aus dem FNCT veranschaulichen keine signifikanten Anzeichen des Schädigungsmechanismus ESC.
Iron aluminides depict a sustainable and light-weight material class which could be employed in many applications requiring high strength at intermediate to high temperatures. According to first results, the alloy Fe-26Al-4Mo-0.5Ti-1B surpasses conventional materials in wet corrosion resistance and creep resistance up to 650 °C. For these reasons, the AiF research project “WAFEAL – Materials applications for iron aluminides” was initiated to transfer these findings into a standardised materials dataset and to derive best practices for processing. In the first place, a set of different microstructures adjusted by varying casting methods, wall thicknesses and heat treatments was investigated and correlated with hardness on macro and micro scale. Correlations were drawn between solidification rates and resulting grain sizes and hardness. The effect of vacancy hardening was only verified for wall thickness as low as 2.5 mm. Moreover, a common decrease of macrohardness after a heat treatment at 1000 °C for 100 h was observed irrespective of casting process or wall thickness. This effect was linked with an unexpected decrease of the complex boride phase fraction which acts as a hardening phase.
Die Digitalisierung von Materialien und Prozessen stellt eine große Herausforderung dar, die nur durch eine Bündelung der Bemühungen aller Beteiligten in diesem Bereich erreicht werden kann. Bei einer derartigen digitalen Beschreibung spielen Datenanalysemethoden, eine Qualitätssicherung von Prozessen inklusive Input- und Output-Daten sowie die Interoperabilität zwischen Anwendungen nach den FAIR-Prinzipien eine wichtige Rolle. Dies umfasst das Speichern, Verarbeiten und Abfragen von Daten in einer vorzugsweise standardisierten Form (Beteiligung von Normungsgremien).
Zur Bewältigung dieser Herausforderung ist eine mit allen Stakeholdern konsistente Kontextualisierung der Materialdaten anzustreben, d.h. alle erforderlichen Informationen über den Zustand des Materials einschließlich produktions- und anwendungsbezogener Änderungen müssen über eine einheitliche, maschinenlesbare Beschreibung verfügbar gemacht werden. Dazu werden Wissensrepräsentationen und Konzeptualisierungen ermöglichende Ontologien verwendet. Eine zentrale Betrachtungsweise in diesem Zusammenhang ist die Realisierung von (automatisierten) Datenpipelines, die eine Beschreibung und Verfolgung von Daten ausgehend von ihrer Erzeugung, bspw. in einem Messgerät, bis zu ihrer globalen Verwendung in möglicherweise verschiedenen Kontexten beinhalten.
Erste Bemühungen und Ansätze zu diesen Problemstellungen führten im Projekt Innovations-Plattform Material Digital (PMD, materialdigital.de) zur Erstellung von Anwendungsontologien, die Prozesse und Testmethoden explizit beschreiben. Dabei wurde u.a. der Zugversuch an Metallen bei Raumtemperatur nach ISO 6892-1 ontologisch beschrieben. Diese als Beispiel dienende Ontologieentwicklung wird in dieser Präsentation vorgestellt. Weiterhin wurde, ausgehend von der domänenspezifischen Entwicklung von Anwendungsontologien, eine Kernontologie erstellt, die eine übergeordnete Verbindung von ontologischen Konzepten aufgrund der Verwendung gleichen Vokabulars und semantischer Verknüpfungen erlaubt. Diese sowie die das PMD-Projekt selbst werden ebenfalls in dieser Präsentation vorgestellt.
The Gibbs free energy of a grain boundary is a complex thermodynamic function of temperature, pressure, and composition. These complexities add to the intrinsic crystallographic and chemical constraints imposed by the adjacent bulk phase. Recently we have proposed a density-based model for assessing grain boundary thermodynamics that enables a CALPHAD-informed description of the grain boundary. As such, the Gibbs free energy of the grain boundary is directly linked with available CALPHAD thermodynamic data. In this talk, new aspects of interfacial segregation and phase transformation are revealed by benchmarking the current model for various experimental cases, including several steels, high-entropy alloys and aluminum alloys. The effects of elastic interactions on the grain boundary segregation and the application of the model to a nanocrystalline Pt-Au alloy, with numerous grain boundaries of various characters, will be discussed.
Die Analyse von Bruchflächen wird in der Schadensanalyse meist auf der Basis von Erfahrungswissen vorgenommen, welches aus vorliegenden Untersuchungen, eigenen Vergleichsversuchen und aus der Literatur stammt. Durch Vergleiche mit bereits vorliegenden Bildern werden qualitativ Bruchmechanismen ermittelt. Grundlage sind zumeist zweidimensionale Bilder aus licht- und elektronenoptischen Verfahren. Quantitative Aussagen beziehen sich bislang beispielsweise auf makroskopische Anteile von Bruchmechanismen oder die Ausmessung von Schwingstreifen. In jüngerer Zeit gibt es vermehrt Ansätze, Computer-Algorithmen einzusetzen, die in der Lage sind, unterschiedlich strukturierte Bruchmerkmale zu finden und zu klassifizieren. Im hier vorgestellten IGF-Vorhaben „iFrakto“, IGF Vorhaben Nr.: 21477 N, werden licht- und elektronen-optisch Topographie-Bilder erzeugt und die gewonnenen 3D-Informationen zusammen mit den klassischen 2D-Bildern ausgewertet. Analytische Algorithmen und Machine Learning werden eingesetzt, um Bruchmerkmale zu analysieren, zu bewerten und mit Informationen aus einer fraktographischen Datenbank zu verknüpfen. Ziel ist die Bereitstellung von Software zur Unterstützung der Fraktographie in der Schadensanalyse. In diesem Beitrag werden erste Ergebnisse des Vorhabens vorgestellt.
Due to the diversity of materials and the processes associated with their production and use, the complexity of the lifecycles of materials and the multitude of academic and industrial researchers participating in generation of data for material design impose a huge challenge. The topical goal of digitalizing materials and processes can only be adequately addressed by consolidating the efforts of all stakeholders in this field. There are many scattered activities, but there is a demand for an elimination of redundancies as well as an advance in acceptance and a common basis in the digitalization of materials. Furthermore, data analysis methods play an important role in both, the experimental and simulation-based digital description of materials, but they have been poorly structured so far.
Therefore, the two joint projects Platform Material Digital (PMD, materialdigital.de) and Materials open Laboratory (Mat-o-Lab, matolab.de) aim to contribute to a standardized description of data processing methods in materials research. Besides stimulating the formation of a collaborative community in this respect, their main technical goals are the quality assurance of the processes and the output data, the acquisition and definition of their accuracy as well as the interoperability between applications. In this regard, data management in accordance with the FAIR (findability, accessibility, interoperability, reuseability) principles is addressed. There is a common agreement in the scientific community following current discussions that data is supposed to be conform to these principles. This includes storage, processing and querying of data in a preferably standardized form.
To meet the challenge to contextualize material data in a way that is consistent with all stakeholders, all necessary information on the condition of the material including production and application-related changes have to be made available via a uniform, machine-readable description. For this purpose, ontologies are to be used since they allow for machine-understandable knowledge representations and conceptualizations that are needed for data management and the digitalization in the field of materials science.
As first efforts in PMD and Mat-o-Lab, application ontologies are created to explicitly describe processes and test methods. Thereby, the well-known tensile test of metals at room temperature was described ontologically in accordance with the respective ISO standard 6892-1:2019-11.
The efforts in creating this tensile test application ontology are shown in this presentation. Especially, the path of ontology development based on standards to be pursued is focused, which is in accordance with the generic recommendations for ontology development and which is supposed to be exemplary for the creation of other application ontologies.
Commercially available carbon steels are suitable for compression and pipelines as long as moisture content and impurities are limited. (water 50 to 100 ppmv, SO2 and NO2 ca. 100 ppmv).
Corrosion rates increase with increasing water content.
(0.2 – 20 mm/a).
Condensation of acids and therefore droplet formation is always possible, even at low water contents.
A low SO2 content within the CO2-stream might be more important than a low water content.
Cr13-steels showed a general susceptibility to shallow pitting and pitting. So, they seem to be not suitable for CCUS applications.
Low alloyed steels showed better corrosion behavior. (predictable uniform corrosion)
For direct contact with saline aquifer fluids only high alloyed steels shall be used.
To apply high-entropy alloys (HEA) of the CrMnFeCoNi family in challenging atmospheres, their degradation behavior under harsh environments needs to be investigated. Oxidation studies to HEAs have not been extensively investigated and most of them are concentrated on environments like synthetic air, laboratory air, CO/CO2, O2 and H2O atmospheres. Main corrosion products which were identified after aging times of up to 100 h are Mn2O3 (≤800°C) and Mn3O4 (≥800°C).
Another corrosive medium in high temperature applications is SO2, which preferentially forms sulfides on commercial steels for example. These can be occurred both in the oxide layer and at the oxide/metal interface. For instance, on Fe-Cr based alloys sulfides (Cr5S6) were detected along grain boundaries and their number increases with exposure time and Cr-content in the alloy. These sulfides show an increased hardness, compared to the bulk alloy, and cause an embrittlement of the grain boundaries. This is a serious material degradation phenomenon, now addressed for the case of HEAs.
In the present study metal sulfides were identified after corrosion of the HEA CrMnFeCoNi alloy in an Ar-0.5vol.%SO2 atmosphere at 800°C for 24 h, 48 h, 96 h and 192 h exposure time. After all three duration times, a thin non-protective Cr2O3 layer has formed at the oxide/alloy interface. At the gas side a thick Mn3O4 layer with local voids containing sulfur could be detected by SEM-EDS analysis. Furthermore, S precipitates could be detected in the bulk material near the surface. These sulfides were characterized in detail by scanning and transmission electron microscopy. Based on these results, a model for grain boundary sulfidation of high-entropy alloy CrMnFeCoNi is discussed.
Bei der Untersuchung von Bruchflächen werden zunächst Beobachtungen gemacht, d.h. makroskopische und mikroskopische Merkmale analysiert und in Bildern dokumentiert. Im zweiten Schritt werden anhand der gefundenen Merkmale Rissverlauf und Bruchmechanismen ermittelt. Abschließend sollen diese Ergebnisse in einem Bericht oder Gutachten zusammengefasst werden. Hierbei ist eine skizzenhafte Darstellung der fraktographischen Befunde hilfreich für das Verständnis des Lesers. Ein vorgefertigter fraktographischer Symbolsatz würde dies erheblich vereinfachen.
Skizzen von fraktographischen Befunden sind in der Literatur recht häufig zu finden, z.B. in der VDI 3822 oder dem ASM Handbook Fractography, allerdings gibt es hierzu keine umfassende Systematik, wie sie z.B. aus der Meteorologie (Wetterkarten), Geographie (Landkarten, Seekarten) oder Geologie (Bodenkarten) seit langer Zeit bekannt sind. Deshalb wird hier der Versuch unternommen, einen Symbolsatz zu entwickeln und zur Verfügung zu stellen, mit dessen Hilfe fraktographische Befunde in eindeutiger und übersichtlicher Weise veranschaulicht werden können. Der fraktographische Symbolsatz ("Fracto Graphics") befindet sich in Entwicklung, ist offen zur Diskussion sowie für Verbesserungen.
The following work deals with the quantitative fracture surface evaluation in damage analysis. So far, fracture surfaces have almost exclusively been evaluated qualitatively, i.e. the presence of fracture features is documented and their surface proportions are estimated, if necessary. Many years of experience are required, as well as an intensive comparison with defined comparative images from the literature. The aim of this work is the development of classifiers which can recognize fracture mechanisms or fracture features in scanning electron microscope images (SEM). The basis is 46 SEM images, which have been evaluated by fractography experts with regard to fracture features. The existing data set of images is expanded using augmentation methods in order to increase the variability of the data and counteract overfitting. Only convolutional neural networks (CNN) are used to create the classifiers. Various network configurations are tested, with the SegNet achieving the best results.
Currently, the Full Notch Creep Test (FNCT) [1] method is used by material suppliers and end users in industry for the approval of container and pipe materials based on high-density polyethylene (PE-HD). The resistance to environmental stress cracking (ESC) of the material is evaluated using the time to failure of the specimen in an aqueous solution of a detergent [2, 3]. Usually specimens made of sheets with isotropic material properties, manufactured by hot pressing, are employed in order to obtain intrinsic properties of the material in terms of ESC failure. In contrast, the processes used in manufacturing to form containers and pipes, such as extrusion blow molding or extrusion, impose anisotropic properties to the material. These are mostly due to a microstructural orientation (polymer chains or crystallites) [4]. Furthermore, the different cooling conditions significantly affect the size distribution of crystallites as well as the overall morphology. It is therefore essential to understand the influence of process-induced material characteristics on failure due to ESC.
A large number of studies on material properties as a function of microstructural preferential orientation have already been conducted [5-7]. However, effects on ESC as the major failure mechanism of containers and pipes are still rather unexplored [8, 9]. The most important factor is whether primarily intramolecular high-strength covalent bonds or the substantially weaker intermolecular van der Waals forces are predominantly loaded.
In addition to the widely established classification by time to failure, the strain or crack opening displacement (COD) provides valuable information about the evolution and progression of damage as a function of time [10, 11]. Optical strain measurement using digital image correlation allows the differences in COD for isotropic and different angles of orientation of anisotropic specimens to be discussed. Also, a post-fracture surface analysis provides clarification on the craze-crack mechanism of the ESC. These different ESC-related properties of extruded and hot-pressed specimens have been investigated at different environmental medium temperatures and different initial stresses to provide a broad characterization of the fracture behavior of PE-HD.
The development of refractory CCAs has been explored for potential use in high temperature applications. An example of this is the AlMo0.5NbTa0.5TiZr alloy, which resembles the well-known γ/γ’ microstructure in Ni-Base superalloys with cuboidal particles embedded in a continuous matrix. The aim of this work is to evaluate the alloy’s mechanical behavior under tension in the temperature range 800-1000°C, by applying creep tests under vacuum (excluding oxidation effects). Some little temperature influence on minimum creep rate @ 1000 and 1100 °C was found and at a first glance, and Norton plots shows that deformation is probably both diffusion and dislocation controlled. However, further work is needed to stablish deformation and degradation micro mechanisms in the studied creep regime.
The refractory chemically complex alloy (rCCA) AlMo0.5NbTa0.5TiZr, with a density of 7.4 g/cm3, shows a compressive ultimate strength of 772 MPa at 1000 °C, comparatively surpassing Ni-base and other rCCAs. Its dual-phase microstructure, with a high volume fraction (≈ 62%) of cuboidal and plate-like particles coherently embedded in a continuous matrix, resembles the well-known pattern of the γ/γ" in Ni-base superalloys. Its developers have thus implied that it could stand as structural alloy for high temperature (HT) applications. Here, we report the HT creep properties and the underlying microstructural changes of the rCCA AlMo0.5NbTa0.5TiZr to propose deformation and degradation micromecanisms for this regime. The material was produced by arc-melting and subsequently heat treated in argon: at 1400 °C for 24 h plus a hot isostatic pressure treatment at 1370 °C and 170 MPa for 4 h, with a cooling rate of 10 K/min. Miniaturized tensile specimens (≈ 28 x 7 x 2 mm) were cut and polished to a quality of 1 μm. Creep tests were conducted in vacuum in the respective temperature and stress range 800-1200 °C and 30-120 MPa. For observation, thin slices were extracted from the gauge length, away from the fracture surface, grinded to a thickness of 100 μm, and electropolished to electron transparency. The microstructure was observed on the electropolished specimens using scanning (S) as well as transmission (T) electron microscopy (EM). The Norton plot gives Norton exponents of about 3.1 and 3.2 for temperatures of 1000 and 1100 °C, respectively. Curiously, creep rate minima are very close for a stress level of 30. The starting microstructure reflects a macroscopically lean coarse grain structure and a microscopically fine-meshed basketweave structure with coherency dislocations only around coarsened particles usually close to subgrain boundaries. Results are discussed on the base of variations of this starting microstructure after interrupted and ruptured creep tests.
A set of some unexpected and interesting microstructures has put the so-called complex concentrated alloys (CCAs) in the eye of the scientific community. The AlMo0.5NbTa0.5TiZr refractory (r)CCA, aimed at substituting Ni-base superalloys in gas turbine applications, belongs to this alloy family. After a two-stage heat treatment, this rCCA morphologically resembles the typical a two-phase microstructure of the latter. The objective of this work consists in determining the effect of the two stages of the heat treatment on the microstructure of the AlMo0.5NbTa0.5TiZr alloy to eventually improve it in terms of homogeneity and porosity.
Ti-6Al-4V alloy is intensively used in the aerospace industry because of its high specific strength. However, the application of Laser Powder Bed Fusion (LPBF) Ti-6Al-4V alloy for structurally critical load-bearing components is limited. One of the main limiting factors affecting the structural integrity, are manufacturing defects. Additionally, the high cooling rates associated with LPBF process result in the formation of large residual stress (RS) with complex fields. Such RS can cause cracking and geometrical distortions of the part even right after production. Also, the microstructure of LPBF Ti-6Al-4V in the as-built condition is significantly different from that of the conventionally produced alloy. All these factors affect the mechanical behavior of the material. Therefore, to improve the material performance it is important to evaluate the individual effect of RS, defects, and microstructure on fatigue life. To this aim Ti-6Al-4V LPBF material in as-built condition and subjected to different post-processing, including two heat treatments (for stress relief and microstructural modification) and Hot Isostatic Pressing (HIP, for densification), were investigated.
Prior to fatigue tests at elevated temperature, the microstructure, the mesostructure, and subsurface RS on the fatigue samples were investigated. It was found that the fatigue performance of HIPped samples is similar to that of conventionally produced Ti-6Al-4V. The tensile RS found at the surface of as-built samples decreased the fatigue life compared to heat-treated samples. Additionally, the modification of the microstructure (by heat treatment) did not affect the fatigue performance in the regime of mostly elastic strain. This shows that in the absence of tensile RS the manufacturing defects solely control the failure of LPBF components and densification has the strongest effect on the improvement of the mechanical performance.
Reliable characterization of materials at the nanoscale regarding their physio-chemical properties is a challenging task, which is important when utilizing and designing nanoscale materials. Nanoscale materials pose a potential toxicological hazard to the environment and the human body. For this reason, the European Commission amended the REACH Regulation in 2018 to govern the classification of nanomaterials, relying on number-based distribution of the particle size.
Suitable methods exist for the granulometric characterization of monodisperse and ideally shaped nanoparticles. However, the evaluation of commercially available nanoscale powders is problematic. These powders tend to agglomerate, show a wide particle size distribution and are of irregular particle shape.
Zinc oxide, aluminum oxide and cerium oxide with particle sizes less than 100 nm were selected for the studies and different preparation methods were used comparatively.
First, the nanoparticles were dispersed in different dispersants and prepared on TEM-supported copper grids. Furthermore, individual powders were deposited on carbon-based self-adhesive pads. In addition, the samples were embedded by hot mounting and then ground and polished.
The prepared samples were investigated by scanning electron microscopy (including the transmission mode STEM-in-SEM) and Dynamic Light scattering. The software package ImageJ was used to segment the SEM images and obtain the particle sizes and shapes and finally the number-based particles size distribution with size expressed as various descriptors.
The relaxation of macroscopic residual stresses in laser powder bed fused stainless steel 316L
(2021)
The processing of stainless steel 316L using the additive manufacturing process Laser Powder Bed Fusion (LPBF) can widen its field of application due to a strong increase in Yield strength, without making major compromises on the ductility nor its outstanding corrosion and oxidation properties. Furthermore, improved designs that either reduce the weight or optimise the function of a part can be obtained using LPBF. These benefits are however counterbalanced by the proneness of LPBF to inducing high Residual Stresses (RS) during manufacturing. The characterisation and monitoring of these RS are of paramount importance for the wider acceptance of the LPBF process. This study focuses on the relaxation of the initial macroscopic RS present in an LPBF 316L as-built prism that undergoes various routes of manufacturing steps to achieve different specimen geometries and stress relieving treatments. The RS are determined using Angle-Dispersive (AD) and Time-of-Flight (TOF) neutron diffraction. The results reveal high tensile RS close to the surfaces and compressive RS near the centre of the as-built parts. The reduction in size and change of geometry heavily impact the stress ranges of the remaining RS, with lower stress ranges in cylindrical shaped compared to rectangular shaped specimens. Also, the application of different stress relieving heat treatments showed that heat-treating temperatures above 800 °C are necessary to obtain a strong relaxation in LPBF 316L.
Thermoelectric generators can be used as energy harvesters for sensor applications. Multilayer thermoelectric generators (ML-TEGs) are a promising alternative to conventional π-type generators due to their high filling factor, high capability of automated production and the texturing potential during the production process. Calcium cobaltite is a promising thermoelectric oxide (p-type) with highly anisotropic properties. The following study shows the development of a textured unileg ML-TEG using ceramic multilayer technology.
Tape-casting and pressure assisted sintering are applied to fabricate textured calcium cobaltite. Compared to conventional sintering, pressure assisted sintering increases the strength by the factor 10. Thermoelectric properties can be tuned either towards maximum power factor or towards maximum figure of merit depending on the pressure level.
As electrical insulation material, a screen-printable glass-ceramic with high resistivity and adapted coefficient of thermal expansion is developed. From various commercial pastes a metallization with low contact resistance is chosen. The unileg ML-TEG is co-fired in one single step. The demonstrators reach 80% of the simulated output power and the power output is highly reproducible between the different demonstrators (99%). These results provide the first proof-of-concept for fabricating co-fired multilayer generators based on textured calcium cobaltite with high power factor, high density, and high strength.
Ceramic multilayer technology is an attractive approach for the cost-effective fabrication of thermoelectric generators. Therefore, efforts are being made to co-sinter two promising thermoelectric oxides, namely calcium cobaltite and calcium manganate. In this study, calcium cobaltite, calcium manganate and release tapes were pressure assisted sintered. A major challenge here is the cracking of calcium manganate during cooling. A relationship between the properties of the release tape used in pressure-assisted sintering and the cracking behavior was observed experimentally.
To understand the origin of failure, formed reaction layers in the multilayer were analyzed by EDX and grazing incident XRD. Based on this analysis, bulk samples were prepared, and thermal expansion and Young's modulus and were determined thereon, if they were not known from the literature. The biaxial strength of the thermoelectric oxides was determined by the ball on three ball method.
The thermal stresses during cooling of different multilayer designs were estimated by finite element simulations. The stresses caused by the reaction layers turned out to be negligible. The FEM study indicated further, and a validation experiment proved, that the thickness of the release tape has the main effect on thermal stresses during cooling in single material. For best performance, the design of a thermoelectric multilayer generator needs to consider thermoelectric performance and thermal stresses during cooling.
Data analysis methods play an important role in both the experimental and simulation-based digital description of materials but have so far been poorly structured. The platform Material Digital (PMD) is supposed to contribute to a standardized description of data processing methods in materials research. The goal is the quality assurance of the processes and the output data, the acquisition and definition of their accuracy as well as the interoperability between applications.
Therefore, application ontologies are created to explicitly describe processes and test methods. In this presentation, the first efforts within the joint project PMD in creating a tensile test application ontology in accordance with the ISO standard 6892-1:2019-11 are shown. Especially, the path of ontology development to be pursued based on standards was focused. Furthermore, the presentation includes a live demonstration of queries possibly performed to query data that was uploaded in the PMD triple store.
Polyethylen hoher Dichte (PE-HD) wird als Werkstoff für Rohre und Behälter für den Transport und zur Lagerung von Gefahrgütern verwendet. Für die Beurteilung und technische Freigabe dieser Materialien ist insbesondere das Verständnis des Schädigungsmechanismus des langsamen, umgebungsbedingten Spannungsrisses (engl.: „environmental stress cracking“, ESC) essentiell. ESC tritt bei relativ geringen auf einen Werkstoff einwirkenden mechanischen Spannungen auf. An lokalen Fehlstellen (z.B. Defekte, Inhomogenitäten, Kerben) beginnend wächst ein Riss langsam durch das Material und führt nach gewisser Zeit zu einem charakteristischen, pseudo-spröden Bruch. Dabei wird das Risswachstum durch äußere Medieneinwirkung zusätzlich entscheidend beeinflusst. Dieses langsame Risswachstum wird als Hauptursache für das plötzliche und unerwartete Versagen von Polymerwerkstoffen angesehen.
Eine etablierte Prüfmethode zur Bewertung des Materialverhaltens gegenüber dieses Schädigungsmechanismus ist der Full-Notch Creep Test (FNCT), der für PE-HD Behältermaterialien üblicherweise unter Verwendung von wässrigen Netzmittellösungen (Arkopal N 100) durchgeführt wird. Die aus dem FNCT erhaltene Standzeit dient dabei als Bewertungskriterium für verschiedene PE-HD-Werkstoffe. In einer Studie wurden neben einer typischen Arkopal-N-100-Netzmittellösung praktisch relevante, organische Flüssigkeiten wie Biodiesel und Diesel als Testmedien verwendet, um deren Einfluss auf das ESC-Verhalten von PE-HD-Behältermaterialien zu charakterisieren. Neben der klassischen Standzeit-Auswertung erfolgte eine erweiterte Bruchflächenanalyse mittels Licht- (LM), Laserscanning- (LSM) und Rasterelektronenmikroskopie (REM). Insbesondere die LSM erlaubt eine schnelle und einfache Unterscheidung pseudo-spröder und duktiler Bruchbilder, die zur Beurteilung der Repräsentativität des FNCT für das dem Spannungsriss zugrundeliegenden langsamen Risswachstum von Bedeutung ist.
Glass fiber reinforced polymer (GFRP) materials in practical applications have to endure cyclic mechanical loading in a wide temperature range (e.g. aircraft applications, automotive, wind turbine blades). In this study the static strength and fatigue behavior of GFRP was investigated in a temperature range from 213 K to 343 K. Therefor the coefficients of thermal expansion of the composite as well as the matrix are measured in this temperature interval. The inverse laminate theory was extended and used to calculate the inter fiber-failure effort for a virtual UD-layer according to the layer wise strength approach. The experimentally determined results are compared with the micro-mechanical model according to Krimmer, which has been enhanced to include the effect of temperature and fiber-perpendicular failure modes. A correlation between matrix effort, the dilatational strain energy of the matrix and the damage state of the specimen is demonstrated. It is shown that a fatigue life assessment can be performed with the aid of a temperature-independent master fatigue curve, as it was similar done for the fatigue behavior of CFRP and GFRP to very high load cycles at room temperature.
As more industrial interests focusing on using salt caverns and repurposed gas or petroleum reservoirs for alternative fuel storage, i.e. CO2/H2, the question raises whether microorganisms may impact the infrastructure, gas purity and storage condition over time.
Environments with high salinity (> 1.5 Meq of NaCl) are resided by halophiles (salt-loving microorganisms). To compensate for the intensive osmotic stress, they have resorted to two main adaptation strategies: 1) production of compatible solutes and 2) accumulation of intracellular KCl. Microbial community analysis of several high salinity environments revealed a number of recurring genera, including Halomonas and Halanaerobium. However, the impact of halophiles on the overall integrity and stability of the storage facilities remain largely unknown.
To evaluate the suitability and stability of saline storage facilities, several model halophilic microorganisms, such as members of Halomonas, will be selected as testing subjects. First, the impact of halophiles on the infrastructure will be determined using an integrative approach by combining a number of techniques, including electrochemistry, TOF-SIMS, SEM/FIB/EDS and FIB-TEM. Second, the abilities of halophiles to alter the fuel composition (i.e. increase/decrease the fractions of H2) will be monitored using gas chromatography by growing them under high pressure.
As a result of climate change and the accompanying mandatory shift to renewable energy resources, microorganisms will continue to play an important role in the energy sector, both to their benefit and detriment. Thus, it is important to achieve a certain level of understanding regarding the activities and mechanisms of halophiles prior to large-scaled excursions.
Since decades electric contacts based on silver metallization pastes are key components of photovoltaics and advanced microelectronics. For the metallization of commercial Si solar cells, high conductive silver glass pastes are cost effectively applicated by screen printing. Nevertheless, silver pastes are still one of the most crucial and expensive none Si materials in solar cells. Ever shorter time to market as well as increasing demands on reduced Ag consumption and line width require the targeted development of silver-glass-pastes with increased sinter ability and electrical conductivity. As a main difficulty, however, the liquid phase sintering of silver glass pastes is poorly understood so far.
In the present study, the influence of different network modifier in alkali-zinc-borate paste glasses on liquid phase sintering of silver-glass-pastes was investigated. Low melting X2O-ZnO-B2O3 glasses with X = Na, Li and Rb (abbr. LZB, NZB, and RZB) were utilized to prepare silver-glass-composites containing 30 %Vol glass. Shrinkage behavior of the silver-glass-composites compared with that of pure silver and pure glass powder compacts was studied with heating microscopy. The powder compacts were uniaxially pressed and heated at 5 K/min to the glass softening temperature. Glass transformation temperature and viscosity of the glasses were respectively measured with dilatometry and rotational viscometry. The thermal behavior of the pure glasses was analyzed with thermal analysis. Additionally, the contact angle of glass on pure silver foil was determined by means of heating microscopy between room temperature and 830 °C.
Thermal analysis of the alkali-zinc-borate-glasses under study has shown transformation temperatures between 450 °C (RZB), 460 °C (LZB) and 465 °C (NZB). For all glasses crystallization was found to start approximately at about 550 °C. However, different peak areas hint on a different degree of crystallization. Conformingly, the sintering behavior, measured in terms of area shrinkage, significantly differed for the silver-pastes under study. For silver-pastes with NZB or LZB-glass, sintering starts at 464 °C for NZB Ag pastes and at 451 °C for LZB Ag pastes and ends at 597 °C for NZB Ag paste and at 594 °C for LZB Ag paste. The sintering of the RZB Ag paste proceeds between 426 °C and 703 °C. The final densification was retarded possibly due to crystallization or swelling. The low sinter onset at 426 °C seems to correlate with the good wetting behavior of the RZB glass. Thus, the lowest apparent contact angle between the just densified powder compact sintered at a silver substrate was found for this glass. Moreover, microstructure analyses of the various composites indicate differences in silver dissolution and reprecipitation.
Network modifier ions can decisively influence properties and structure of low melting alkali-zinc-borate glasses and thus cause complex effects on the liquid phase sintering of silver-glass metallization pastes. This effect was studied for X2O-ZnO-B2O3 (X = Li, Na, Rb) glasses for silver-glass metallization pastes. Viscosity and the glass transition temperature, Tg, were measured with rotational viscometry and dilatometry. Dried model pastes with 30 vol% LZB, NZB or RZB glass were prepared for sintering studies by means of heating microscopy measuring the silhouette area shrinkage of uniaxially pressed powder compacts during heating at 5 K/min. For comparison, the silhouette area shrinkage of pure glass and silver powder compacts were determined. Glass-silver wetting was investigated during heating of bulk glass cylinders placed on silver substrates. Glass RZB turned out to have the lowest viscosity among the glasses under study. Its glass transformation temperature, Tg, was found at 444 °C and it caused the lowest sintering onset for its glass and paste powder compacts. Slightly increased values of Tg were found for NZB and LZB (468 °C and 466 °C, respectively) and a slightly retarded sintering was found for both paste powder compacts. These results indicate that liquid phase sintering of silver-glass pastes under air atmosphere is mainly influenced by glass viscosity.
In many late-breaking research fields as in photovoltaics, microelectronics, nuclear waste glasses or at least mirror glasses silver diffusion in glasses is relevant to the issues of high-level functionality and recycling. The present study is focused on silver diffusion in innovative, low-melting alkali zinc borate glasses (X2O-ZnO-B2O3, X = Li, Na, K, Rb) potentially usable for silver metallization-pastes in solar cells. The glasses were coated with a thin metallic silver layer and heat treatments in air and nitrogen close to Tg at 470 °C for 2 h were performed. After heat treatment under air and nitrogen atmospheres the coating thickness, measured by a white light interferometer, was about 1.8 µm thick. Silver depth profiles determined by means of secondary neutral mass spectrometry (SNMS) indicate the fastest silver diffusion to a depth of 3.5 µm for Li2O-ZnO-B2O3 (LZB) glass. Nevertheless, the influence of the different alkali ions on the silver diffusion is small. The oxygen availability determines the silver diffusion into the glasses. The oxygen promotes the oxidation of the silver layer enabling Ag+ to diffuse into the glass and to precipitate as Ag0. Both species were detected by x-ray absorption spectroscopy (XAS). The precipitated metallic silver particles in Na2O-ZnO-B2O3 (NZB) glass have a mean size of 5.9 nm ± 1.2 nm diameter, which was determined using transmission electron microscopy (TEM). Phase separation in zinc-rich and zinc-poor phases with a mean diameter of 75 nm ± 20 nm occurred in NZB glass after heat treatment. Ion diffusion of the glasses into the silver layer was suggested by EDX-line scans.
Thermoelektrische Generatoren können zum „Energy harvesting“ für den autarken Betrieb von bspw. Sensoren eingesetzt werden. Eine interessante Alternative zu den herkömmlichen π-Typ Generatoren sind auf Grund der höheren Leistungsdichte und der guten Automatisierbarkeit thermoelektrische Multilayergeneratoren. Calciumcobaltit ist ein vielsprechendes oxidisches Thermoelektrika (p-Typ) mit stark anisotropen Eigenschaften. Die hier vorgestellte Studie zeigt die Entwicklung von texturierten Unileg-Multilayer-Generatoren mittels keramischer Multilayertechnologie.
Calciumcobaltit wird durch Foliengießen und druckunterstützte Sinterung texturiert. Im Vergleich zur konventionellen Sinterung verbessert sich die Festigkeit um den Faktor 10. Die thermoelektrischen Eigenschaften können je nach verwendetem Druckniveau hinsichtlich maximalem Power Factor oder hinsichtlich maximalem Gütefaktor optimiert werden.
Ein Glaskeramikkomposit wird als Isolationsmaterial mit hohem Volumenwiderstand und angepasstem Wärmeausdehnungskoeffizienten entwickelt. Der Unileg-Multilayer-Generator wird in einem Schritt co-gesintert. Die hergestellten Demonstratoren erreichen 80% der simulierten Output-Leistung. Diese Ergebnisse stellen den ersten Machbarkeitsnachweis für die Herstellung von co-gesinterten Multilayer-Generatoren aus texturiertem Calciumcobaltit mit hohem Power Factor und hoher Festigkeit dar.
Study of Polyaniline/Silicon Dioxide based Coating on Carbon Steel in Artificial Geothermal Brine
(2021)
By using the available resources in Indonesia, such as silicon dioxide and marine coating base, the PANI/SiO2 modified alkyd coating was able to protect carbon steel in a deaerated artificial geothermal water. The screening of coatings shows that the modification by adding individual pigment was not sufficient to protect carbon steel even during a short-term exposure, indicated by the discoloration after only seven days of exposure. Electrochemical tests indicated that there was no significant change in the Ecorr between the coated and uncoated carbon steel at room temperature. At 150 °C, the coated carbon steel has a lower potential than that of carbon steel, indicating that the coating is protecting carbon steel cathodically or slowing down the corrosion reaction. Finally, a long-term exposure test confirmed that the PANI/SiO2 modified coating successfully protects the carbon steel in the Sibayak artificial geothermal water up to 150 °C for 6 months.
Wind turbine rotor blades commonly fail before their projected 20-year lifespan largely due to defects that originate during manufacturing and are propagated by operational fatigue and environmental conditions. The cost-intensive replacement outcomes lead to a high loss of earnings, and are one of the inhibitors of wind turbine production. A potential repair alternative to restoring the mechanical properties of such lightweight fiber reinforced polymer (FRP) structures is to locally patch these areas with scarf joints. This type of repair allows for a smoother load distribution across the joint, and is favored especially on structures where minor aerodynamic contour changes are key. The effects of such repairs on the structural integrity, however, is still largely unknown. Building upon an understanding of the static load failure mechanism of GFRP scarf joints, presented at the ICCS23 Joint Event in 2020, the influence of the fiber orientation mismatch between parent and repair materials of 1:50 scarf joints on the failure mechanism of monolithic glass FRP specimens under cyclic fatigue load were examined in this study. Specimens with various layups were produced with the vacuum-assisted resin infusion (VARI) process using biaxial E-glass non-crimp fabric (NCF). The patch layers were then joined directly to the parent structure with the VARI using biaxial E-glass NCF with half the areal weight of the parent side to allow for better drapability. This mimics the soft-to-hard patch style utilized in wind turbine blade shell field repairs. The specimens were tested under uniaxial fatigue load, during which they were periodically monitored for damage onset. A comparison of the +45/-45° and 0/90° layups allowed for an understanding of the role of a highly mismatching fiber orientation in the transition zone between parent and patch material on the failure mechanism of the scarf joint. In addition to the tensile strength and stiffness property recovery assessment, a grayscale analysis using in-situ camera images determined the damage state leading to failure in each region across the scarf joint, which varied in the parent material versus scarf joint region, providing insight to the critical regions in this composite structure under cyclic loading.
Monodisperse iron oxide nanoparticles as reference material candidate for particle size measurements
(2020)
In order to utilize and rationally design materials at the nanoscale the reliable characterization of their physico-chemical properties is highly important, especially with respect to the assessment of their environmental or biological impact. Furthermore, the European Commission’s REACH Regulations require the registration of nanomaterials traded in quantities of at least 1 ton. Powders or dispersions where 50% (number distribution) of the constituent particles have sizes ≤ 100 nm in at least one dimension are defined as nanomaterials. This creates a need for industrial manufacturers and research or analytical service facilities to reliably characterize potential nanomaterials. Currently, BAM is developing reference nanoparticles, which shall expand the scarce list of worldwide available nano reference materials certified for particle size distribution and will also target other key parameters like shape, structure, porosity or functional properties. In this respect, materials like iron oxide or titanium dioxide are considered as candidates to complement the already available silica, Au, Ag, and polystyrene reference nanoparticles.
The thermal decomposition of iron oleate precursors in high boiling organic solvents can provide large quantities of iron oxide nanoparticles that can be varied in size and shape.[1, 2] The presence of oleic acid or other hydrophobic ligands as capping agents ensures stable dispersion in nonpolar solvents. Such monodisperse, spherical particles were synthesized at BAM and pre-characterized by electron microscopy (TEM, SEM including the transmission mode STEM-in-SEM) and dynamic light scattering comparing cumulants analysis and frequency power spectrum.
1. REACH regulations and nanosafety concerns create a strong need for nano reference materials with diverse properties.
2. Iron oxide nanoparticles are under development as new candidate reference material at BAM.
3. Narrow particle size distribution confirmed by light scattering and electron microscopy.
As a type of high-performance composite material, glass-fiber reinforced plastics (GFRP) are favored for the construction of wind turbine rotor blades due to their high specific strength and stiffness properties (Grasse et al, 2010). During the blade manufacturing process, however, imperfections are often introduced, then further propagated due to harsh environmental conditions and a variety of loads (Caminero et al, 2013; Trappe et al, 2018). This leads to failure significantly before their designed lifespan. Since replacement of entire blades can be a costly potential outcome, localized repairs of the damaged region to restore structural integrity and thus lengthen its lifespan can executed in the field by technicians accessing the blades directly by suspended roping. These methods involve replacing the lost load path with a new material that is joined to the parent structure. In recent years, considerable studies have been conducted to investigate the influence of different repair parameters on the stress distribution, ultimate strength, impact behavior, and residual stresses of bonded repaired structures [Caminero et al, 2013; Trappe et al, 2018; Shufeng et al, 2014; Harman and Rider, 2011; Ahn and Springer, 2000; Lekou and Vionis, 2002). However, there currently do not exist any standardized repair procedures for wind turbine rotor blades. Namely, there is a lack of understanding about the effects of the layup of various repair methods, especially on the damage mechanism and fatigue life of the shells of rotor blades (Caminero et al, 2013; Trappe et al, 2018).
This work therefore aims to begin to enrich this knowledge gap by testing the influence of different variables among repair patches on the mechanical properties of sandwich composite structures. Manufactured with the vacuum-assisted resin infusion (VARI) process, the test specimens are produced as a GFRP structure to represent the outer shell portion of a wind turbine blade, then repaired with a scarf joint. Scarf repairs are favored as the most efficient of the common structural joints, as the removal of the damaged area with angled walls leads to a nearly uniform shear stress distribution along the bond surface and no eccentricity in the load distribution (Caminero et al, 2013; Lekou and Vionis, 2002; Siener, 1992).
The performance of specific layup methods of repair patches, namely a large-to-small versus small-to-large scheme of repair layers, is studied with static and load-controlled fatigue testing, then compared to pristine test specimens as well as to each other in terms of mechanical property restoration. The transition layer between repair and parent material is especially of interest in the performance of the structure. Damage onset, crack development and eventual failure are monitored in-situ with non-destructive testing methods, including thermography with an infrared camera system and a 3D deformation analysis system, to develop a more robust understanding of the effects of these repair concept variables on wind turbine blade shell structures.
This presentation shows some experimental results of the characterization of the creep behavior of LPBF 316L, which has been poorly studied and understood to date. The presentation includes results regarding the mechanical properties, the initial microstructural state and its evolution under loading, and the damage mechanism. This work was done within the BAM focus area materials project AGIL. As a benchmark to assess the material properties of the LPBF 316L, a conventionally manufactured variant was also tested.
The underlying cause of mechanical anisotropy in additively manufactured (AM) parts is not yet fully understood and has been attributed to several different factors like microstructural defects, residual stresses, melt pool boundaries, crystallographic and morphological textures.
To better understand the main contributing factor to the mechanical anisotropy of AM stainless steel 316L, bulk specimens were fabricated via laser powder bed fusion (LPBF).
Tensile specimens were machined from these AM bulk materials for three different inclinations relative to the build plate. Dynamic Young's modulus measurements and tensile tests were used to determine the mechanical anisotropy. Some tensile specimens were also subjected to residual stress measurement via neutron diffraction, porosity determination with X-ray micro-computed tomography, and texture analysis with electron backscatter diffraction (EBSD). A crystal plasticity model was used to analyze the elastic anisotropy and the anisotropic yield behavior of the AM specimens, and it was able to capture and predict the experimental behavior accurately. Overall, it was shown that the mechanical anisotropy of the tested specimens was mainly influenced by the crystallographic texture.
The cyclic crack tip opening displacement ΔCTOD is a promising loading Parameter to quantify the crack propagation under thermomechanical fatigue (TMF). In this work, suitable techniques are investigated and compared for an accurate calculation of ΔCTOD under TMF loading using a viscoplastic temperature dependent material model.
It turned out that collapsed special crack tip elements give the best results. An efficient FEM-technique is developed to simulate the incremental crack growth by successive remeshing, whereby the deformations and internal state variables are mapped from the old mesh onto the new one. The developed techniques are demonstrated and discussed for two-dimensional examples like TMF-specimens. Recommendations are made regarding important numerical control parameters like optimal size of crack tip elements, length of crack growth increment in relation to plastic zone size and ΔCTOD value.
The dielectric breakdown strength of ceramics strongly depends on the test conditions. Thus, standardized test procedures and thorough documentation are indispensable. However, during dielectric strength testing the breakdown often occurs near the electrode edge or even outside the specified electrode area. This behavior is similarly observed for printed and cylindrical electrodes. The aim of the presented study was to calculate the electric field strength distribution in a ball-on-plate testing setup for metallized samples and to correlate the field distribution with the observed breakdown locations. Small misalignments in the test setup were also considered in the simulations. Furthermore, the field strength at the breakdown Location should be compared to the experimentally determined dielectric strength. Therefore, Finite Element Models of several test conditions with varying printed electrode areas and sample thicknesses were created and electrostatic calculations of the electric field Distribution were performed. The simulation results were compared to experimental data. Alumina (96 %) was used as test material. The calculations show that the electric field strength maxima match the experimentally observed locations of breakdown. Without any fitting of the model, the maximum calculated field strength is in reasonable agreement with the experimental dielectric strength. The FE analysis is a helpful tool to understand the observations in experimental dielectric strength testing.
The use of increasingly finer starting powders up to nanopowders can also be observed in the field of ceramics. Their advantages consist, for example, in their lower activation energy, an increase in strength or unique optical properties. However, handling and characterization of the powders are much more difficult. The main reason for this is the very high adhesive forces between the particles and between particles and other surfaces, too. Therefore, submicron and even more so nanoparticles tend to agglomerate and their separation into primary particles during sample preparation prior to particle sizing is of particular challenge. A representative measurement sample is only obtained when it no longer contains agglomerates. The evaluation of the dispersion process and a decision on whether it was successful thus increases in importance for the reliability of the measurement results of particle sizing.
The presentation uses examples to show possible approaches and provides information on possible sources of error.
It is shown that successful granulometric characterisation of fine powders requires both an improved dispersion technique and very often an effective combination of two or more measurement methods.
Al2O3 coatings are often used as protective layers on steels against electrochemical and high-temperature corrosion because they are chemically inert and stable at elevated temperatures. This study presents preliminary work on the possibilities of using Al2O3 sol-gel coatings for corrosion protection of martensitic stainless steels in geothermal environments. Al2O3 sol-gel coatings were applied on UNS S42000, which is known to be susceptible to uniform and localized corrosion. The coated steel specimens were then tested in two types of artificial geothermal water, which simulate the geothermal fluids found in Sibayak (SBY), Indonesia, and North German Basin (NGB), Germany, respectively. SBY has pH 4 and 1.5 g/L of chloride ions, whereas NGB has a pH of 6 and 166 g/L of chloride ions. All experiments were carried out in autoclaves at 150 °C and 1 MPa under the deaerated condition. Evaluations were performed by investigating the surface profiles of both uncoated and coated steels before and after the corrosion test using a Laser Scanning Microscope (LSM) and Scanning Electron Microscope (SEM). Finally, Electrochemical Impedance Spectroscopy (EIS) was performed to compare the corrosion resistance of Al2O3 coated steels in SBY and NGB solutions. It was observed from the corrosion test that Al2O3 coatings are more suitable for use in the geothermal water with a higher pH.
CO2 quality specifications are not only a matter of CO2 purity (i.e. CO2 content).
The “rest” also matters, in particular contents of reactive impurities affecting material corrosion (and rock alteration).
Also chemical reactions in CO2 stream needs to be considered, in particular when combining CO2 streams of different compositions.
Texturing of calcium cobaltite for thermoelectric applications by pressure assisted sintering
(2021)
Thermoelectric materials can convert waste heat directly into electrical power by using the Seebeck effect. Calcium cobaltite (CCO) is considered as a promising thermoelectric p-type oxide for energy harvesting applications at temperatures above 500 °C. The properties and morphology of single-crystal CCO are strongly anisotropic because of its crystal structure of alternating layers of CoO2 and Ca2CoO3. By aligning the plate-like grains, the anisotropic properties of the grains can be assigned to the poly-crystalline parts.
In this study, the combination of tape casting and pressure-assisted sintering is used to texture and densify large scale components (50 cm²). Thereby, the influence of powder preparation and applied pressure during sintering on texturing and thermoelectric properties is investigated.
The analysis of XRD pole figures revealed that tape casting already leads to highly textured CCO. By pressure variation during sintering, the microstructure of CCO can be tailored either toward maximum power factor as required for energy harvesting or toward maximum figure of merit as required for energy recovery. Low pressure lead to a porous microstructure and maximum figure of merit and higher pressure to full densification and maximum power factor. The electrical and thermal conductivity of CCO seem depending on both texture and sinter density.
Multilayered designs are an attractive approach towards cost-effective manufacturing of thermoelectric generators. Therefore, efforts are being made to co-fire two promising thermoelectric oxides, namely calcium cobaltite and calcium manganate. In this study, ceramic tapes, multilayer technology, and pressure-assisted sintering (PAS) were used. A major challenge for the PAS of low-sintered calcium manganate was cracking during cooling. A relationship between the properties of the release tape used during PAS and the cracking behavior was experimentally observed.
To understand the origin of failure, reaction layers in the multilayer were analyzed and thermal stresses during cooling were estimated by finite element (FE) simulations. Thermal expansion, elastic properties, and biaxial strength of the thermoelectric oxides and selected reaction layers were determined on separately prepared bulk samples. The analysis showed that the reaction layers were not the cause for cracking of calcium manganate.
Using the FE model, thermal stresses in different manganate multilayer designs with varying properties of the release tape were studied. The FEM study indicated, and a validation experiment proved that the thickness of the release tape has the main effect on thermal stresses during cooling in separately sintered calcium manganate.
A variety of materials of technological interest change their properties through contact with reactive media. Solid-gas reactions lead to a variety of reaction products on the surfaces and internal interfaces. The observation of nucleation and growth processes in the environment where they occur (in situ) from a chemical-structural perspective is especially challenging for aggressive atmospheres. The talk presents innovative approaches to study corrosion mechanisms using advanced X-ray methods. Using energy dispersive X-ray diffraction and X-ray absorption spectroscopy in different tailor made environmental reaction chambers, valuable insights into high temperature oxidation and sulfidation processes were gained. Fe-based alloys were exposed to hot and reactive atmospheres containing gases like SO2, H2O and O2 at 650°C. During the gas exposure the tailor made reaction chambers were connected to a high energy diffraction end station at the synchrotron. The crystallization and growth of oxide and sulfide reaction products at the alloy surfaces were monitored by collecting full diffraction pattern every minute. Careful examination of shape and intensity of phase-specific reflections enabled to a detailed view on growth kinetics. These studies showed, oxides are the first phases occurring immediately after experimental start. As soon as reactive gas media enter the chamber, the conditions change and different reaction products, such as sulfides start to grow. A comparison of different gas environments applied, illustrated the differences in the type of reaction products. The in situ observation of high temperature material degradation by corrosion made it possible to study the contribution of phases, which are not stable at room temperature. For instance, wuestite (Fe1-xO), was frequently observed at high temperatures in humid gases on Fe with 2 wt.% and 9 wt.% chromium, but not at room temperature. The strength of the occurrence of this phase additionally explains why, despite a higher Cr content, ferritic alloys with 9 wt.% Cr in a challenging atmosphere prevent the intrinsic formation of protective layers. The in situ observations were supplemented by careful considerations of thermodynamic boundary conditions and detailed post characterization by classical metallographic analysis. Additionally, the structure and chemistry of the dominant oxide layers were evaluated using X-ray absorption near edge structure spectroscopy. The talk will give an overview about chances and challenges for studying high temperature corrosion phenomena by advanced X-ray methods.
The discovery of the high entropy concept at the beginning of the 3rd millennium lead to a worldwide increase in metallurgical research, as the possible element combinations seemed nearly endless and the range of applications wide. In the early years of research, one of the main goals was the discovery of a single-phase high entropy alloy. As research evolved, it was found that properties could be enhanced by opening the HE-concept towards multiphase alloys, and from the wide area of possibilities our group chose a tuning of the properties towards high temperature application.
Compositionally complex Al10Co25Cr8Fe15Ni36Ti6 alloy, which is single-phase at high temperature, around 1200°C, shows a three phase morphology at intermediate temperatures, around 800°C. A high temperature homogenization procedure has to be applied in order to decrease the segregation induced by the dendritic growth. Subsequent annealing promotes the formation of the strengthening γ' precipitates. The alloy shows a positive lattice misfit between the γ and the γ' phase, which can be an indicator for good creep properties.
The microstructure can be optimized by adding trace elements such as Mo and Hf, known as γ and γ' strengtheners in Ni-based superalloys, respectively. Atom probe measurements show that Mo segregates into the γ matrix, and Hf prefers the γ' precipitates, where it increases the lattice parameter and thus also the lattice misfit, by about 50%. The alloy family shows interesting mechanical properties, especially the Al9.5Co25Cr8Fe15Ni36Ti6Hf0,5 alloy – its tensile properties are better than those of commercial Alloy 800H and IN617 at temperatures up to 700°C.
Thermoelectric generators can be used for energy harvesting by directly transforming a temperature gradient into a voltage. Multilayer generators based on low-temperature co-fired ceramics technology (LTCC) are an interesting alternative to conventional π-type generators. They exhibit several advantages like high filling factor, possibility of texturing, co-firing of all materials in one single-step, and reduction of production costs due to the high possible degree of automation. Pressure-assisted sintering enables the theoretical possibility of co-firing two promising oxide thermoelectric materials: Ca3Co4O9 (p-type) and CaMnO3 (n-type). Due to the large difference in sintering temperature (300 K) the process is very challenging.
In this work we show the material development of Ca3Co4O9, CaMnO3, insulation and metallization for multilayer generators co-fired under pressure at 900 °C. The materials are tailored regarding their sintering behavior, electrical performance and coefficients of thermal expansion. Different generator designs (unileg and pn-type) were fabricated and analyzed regarding crack formation, interaction layers and thermoelectric performance. Simulated stresses during cooling in the multilayers are compared with actual crack formation for different sintering conditions. This study shows that a lower pressure level and a lower level of complexity are beneficial for co-firing and performance.