5 Werkstofftechnik
Filtern
Dokumenttyp
- Vortrag (16)
- Beitrag zu einem Tagungsband (13)
- Zeitschriftenartikel (1)
- Beitrag zu einem Sammelband (1)
- Sonstiges (1)
- Posterpräsentation (1)
Sprache
- Englisch (24)
- Deutsch (8)
- Mehrsprachig (1)
Referierte Publikation
- nein (33) (entfernen)
Schlagworte
- Fatigue (6)
- Non-destructive testing (4)
- Polymer matrix composites (4)
- Wind turbine blades (4)
- Composite (3)
- Betriebsfestigkeit (2)
- Cross linking (2)
- Cure process (2)
- Dynamic mechanical analysis (DMA) (2)
- Faserkunststoffverbunde (2)
- Fatigue of sandwich shell structures (2)
- Glass fiber reinforced polymers (2)
- Luftultraschall (2)
- Polymer Matrix Composites (2)
- Temperature (2)
- Thermomechanics (2)
- Thermoset polymers (2)
- Windenergie (2)
- Air-coupled ultrasonic testing (1)
- Airborne ultrasonic testing (1)
- Alterung (1)
- CFK (1)
- Carbon Fibers (1)
- Carbon fibre-reinforced-plastics (1)
- Certification Standard 22 (1)
- Composite structures (1)
- Composite testing (1)
- Composites (1)
- Damage (1)
- Damage evolution (1)
- Distributed fiber optic sensors (1)
- Distributed fibre optic sensors (1)
- EASA (1)
- Epoxy (1)
- Erneuerbare Energien (1)
- Faser-Kunststoff-Verbunde (1)
- Fatigue Life Evaluation (1)
- Ferroelectret (1)
- Ferroelektret (1)
- Fiber reinforced polymer (1)
- Fracture (1)
- General Aviation (1)
- Glass fiber reinforced polymer (1)
- Glass fibre reinforced plastics (1)
- Klebung (1)
- Kurzfaser-verstärkte Thermoplaste (1)
- Laminographie (1)
- Laminography (1)
- Lightweight materials (1)
- Lightweighting (1)
- Materialmodell (1)
- NDT (1)
- New standards (1)
- Nondestructive testing (1)
- Normung (1)
- Optical backscatter reflectometry (1)
- Optical fibre (1)
- Photon counting detector (1)
- Push-out Test (1)
- Recycling (1)
- Repair of sandwich shell structures (1)
- Repair patch (1)
- Residual stresses (1)
- Rissentwicklung (1)
- Rohrprobekörper (1)
- Rotor blade (1)
- Rotorblatt (1)
- Rotorblattschalen (1)
- Röntgen-Refraktion (1)
- Sailplane Development Panel (1)
- Sandwich (1)
- Scarf repairs (1)
- Schalenprüfstand (1)
- Self-healing (1)
- Structural health monitoring (SHM) (1)
- Swept wavelength interferometry (SWI) (1)
- Synchrotronstrahlung (1)
- Thermo mechanical fatigue (1)
- Thermo-mechanical-loading (1)
- Thermo-mechanics (1)
- Thermographie (1)
- Thermoplastic (1)
- Transducers (1)
- Very high cycle fatigue (1)
- Wandler (1)
- Werkstoffprüfung (1)
- Wind energy (1)
- Wind turbine (1)
- Windkraft (1)
- X-ray laminography (1)
- X-ray refractography (1)
- Zug-Druck-Schubprüfung (1)
- multi scale testing (1)
- thermomechanische Beanspruchung (1)
Organisationseinheit der BAM
- 5 Werkstofftechnik (33) (entfernen)
Eingeladener Vortrag
- nein (16)
3D structural investigations are described by X-ray laminography studies of sandwich shell segments, made of a PVC foam core, covered by non-crimp fabric glass fibre composite lay-ups processed by vacuum assisted resin infusion of epoxy. The specific scope of this study is to image transversal flaws within the foam core (joints) and of single ply overlaps. Test flaws were purposely implemented in order to simulate typical failure under cyclic load. In a dedicated test rig for shell structures, the flaw evolution/propagation is monitored by thermography and optical 3D inspection of deformation. Due to the unfavourable preconditions for classical computed tomography as of large aspect ratio, the samples were investigated by coplanar translational laminography. Its limited range of observation angles of ± 45°, results in anisotropic artefacts about the normal to the sample surface, but the typical flaws are well visualized in the as-prepared state, in a state of early damage, and in the repaired state.
Cyclic fatigue behavior of glass fiber reinforced epoxy resin at ambient and elevated temperatures
(2018)
The fatigue behavior of ±45° glass fiber reinforced epoxy resin under cyclic mechanical and constant thermal loading is investigated in this study. Tests at three different temperature levels in the range 296 K to 343 K have been performed in order to create S-N curves for each temperature level. The specimen damage is measured in-situ using optical grayscale analysis. The characteristic damage state (CDS) is evaluated for each specimen. It is shown that the point of CDS is suitable as a failure criterion to compare the resulting S-N curves. With micromechanical formulations, the temperature-dependent matrix effort is calculated for each stress-temperature level. In terms of matrix effort, the longest fatigue life is reached at high temperatures, while, in terms of stress, the lowest fatigue life is reached at the highest temperatures.
Um den sicheren Betrieb von Windkraftanlagen zu gewährleisten, werden Rotorblätter nach der Fertigung und nach Reparatur mit verschiedenen zerstörungsfreien Verfahren auf Schaden untersucht. Bei der Fertigung von Blattschalen, die in einer Sandwich-Schalenbauweise gefertigt werden, entstehen Imperfektionen, die unter Belastung zu großen Rissen führen können. Zur Prüfung von Blattschalen wird unter anderem Ultraschallprüfung in Kontakttechnik eingesetzt. Um den Wartungsaufwand von Ultraschallanlagen zu reduzieren und um manche Kompositstrukturen vor Koppelmittel zu schützen, wird die Anwendung von Luftultraschall erforscht. Insbesondere große Fortschritte gibt es im Bereich der Entwicklung neuer Wandler.
In diesem Beitrag berichten wir über die Luftultraschallprüfung von Schalen für Rotorblätter. Es wurden typische Sandwichschalenstrukturen hergestellt und mit einem eigenentwickelten Schalenprüfstand unter simulierter Betriebsbeanspruchung belastet. Die in den Schalenprüfkörpern entstandenen Schäden wurden außerhalb des Prüfstandes mit Luftultraschall in Durchschallung untersucht. Es wurden fokussierende Wandler auf Basis von Ferroelektreten entwickelt und für diese Prüfungen eingesetzt. Mit zusätzlicher elektrischer Vorspannung konnte die Empfindlichkeit der Empfänger deutlich erhöht werden. Die nach dem Lastwechsel entstandenen Schäden in den Rotorblattschalen waren eindeutig zu detektieren.