Filtern
Erscheinungsjahr
- 2011 (4) (entfernen)
Dokumenttyp
- Beitrag zu einem Tagungsband (4) (entfernen)
Referierte Publikation
- nein (4)
Schlagworte
- DLC (2)
- ZrCN (2)
- Additive (1)
- Additives (1)
- Biomotox (1)
- Drain (1)
- Dünnschichten (1)
- Extrembeanspruchung (1)
- Fuel economy (1)
- Head capacity (1)
Wear tests are often used in engine development in order to characterize the functional profile of surfaces interacting with lubricants. This paper proposes a new test procedure to determine Stribeck-type curves for the tribosystem piston ring/cylinder liner involving test pieces prepared from engine components. The Variation of the friction coefficient with sliding speed depends on the structure and Constitution of the base oil, the viscosity index, the surface topography of the liner and ring, and the friction modifiers used. Novel organic friction modifiers of low molecular mass not only reduce the friction coefficients under mixed / boundary lubrication, but also in the fluid film regime. In addition, the influence of surface roughness on the wettability of surfaces can be significant for both static and dynamic wetting. For this reason, the interaction of the lubricant with the surfaces was also investigated to enable a correlation between the surface properties of the liquid and solid phases and the tribological behavior.
OEMs perceive diamond-like carbon (DLC) coatings as part of a strategy for low frictional tribosystems. Especially the automotive industry anticipates a benefit in applying such coatings in association with the lightweight construction of mechanical parts, for instance in gears and engines. In previous investigations it was shown, that DLC, amorphous carbon (a-C) and tetragonal amorphous carbon (ta-C) coatings can be slip-rolling resistant at least up to ten million load cycles at Hertzian contact pressures P0max of 2.9 GPa lubricated by engine oil at 120°C, Further improvements in load carrying capacity up to P0mean of 2.62 GPa (FN= 5,000 N) were achieved with alternative, available Steel metallurgies as Substrates for thin film coatings. Additional factors, such as influences of the lubrication on the surface chemistry (additives and base oils), wear and friction behavior were investigated.
Leichtbaustrategien im Antriebsstrang erhöhen durch Downsizing die Hertz’schen Kontaktpressungen und die mechanischen Lasten. Dadurch müssen neben wälzbeständigen Stählen auch dazu passende reibungsmindernde Konzepte gefunden werden, in der vorliegenden Arbeit wurden alternative, hoch zähe Stähle mit einer Wälzbeständigkeit bis Pomax = 4,2 GPa untersucht, welche mit geeigneten Grundöl- und Additivkombinationen die Reibungszahlen herunter auf 0,025 reduzieren konnten. Diese alternativen Stahllegierungen erlauben nicht nur an der Zahnflanke sehr hohe Kontaktpressungen, sie bieten außerdem entsprechende Zähigkeits- und Festigkeitseigenschaften für den Zahnfuß. In vorangegangenen Untersuchungen wurde eine Vielzahl verschiedener Dünnschichten auf ihre Überrollbeständigkeit unter Extrembeanspruchungen validiert. Allerdings zeigte sich bei den meisten Dünnschichten ein Qualitätsunterschied von Charge zu Charge. Unter Verwendung verschiedener organischer, metallorganischer und anorganischer Additive konnten, sich daran anschließende Versuche, vielversprechende Ergebnisse erzielt werden. Sämtliche Versuche unter extremen Beanspruchungen wurden bei +120°C Öltemperatur auf Zwei-Scheiben-Tribometern vom Typ AMSLER und 2Disk von Optimol Instruments unter Misch-/Grenzreibungsbedingungen durchgeführt und die tribologischen Eigenschaften der neuartigen, unbeschichteten Stähle und in Relation zu leistungsstarken DLC-/ZrCN Dünnschichten gesetzt.