Filtern
Dokumenttyp
Schlagworte
- Radar (3)
- Concrete (2)
- Impact-echo (2)
- Betonbauteile (1)
- Betondeckung (1)
- Concrete cover of tendon ducts (1)
- Concrete slabs (1)
- Dickenmessung (1)
- Drive pinion (1)
- Durchstrahlungsverfahren (1)
Validation of non-destructive testing methods is necessary to create a common basis where different systems can be compared and their applications and limitations be identified. This can be achieved through comparing the measurements taken by several systems used for a common diagnostic purpose under practical but controlled testing conditions. Well-designed small and large laboratory or field specimens promise such conditions.
The special concrete specimen (LCS) at BAM was constructed for validation purposes, in particular, to be used for evaluating the performance of echo methods. The thickness of the specimen is varying and it contains carefully designed built-in faults, such as voids, honeycombs and tendon ducts with various degrees of grouting defects. Since the geometry and condition of the defects are known, it can be used to compare the performance of radar, ultrasonic, impact-echo. The research was conducted within the Research group FOR384, sponsored by the German Research Society DFG.
+ Der Schutz der Beschäftigen und der Öffentlichkeit und die sichere Handhabung von
umschlossenen Quellen in der technischen Radiographie ist durch die Beachtung aller Regeln
(Gesetze, Verordnungen und Standards) gewährleistet.
+ Nach derzeitigem Kenntnisstand sind die dargestellten Maßnahmen für die Gamma-
Radiographie aus Sicht der Anwender ausreichend.
+ Der Standort einer radioaktiven Quelle wird durch ihre Registrierung in das HRQ- Register
und bei der örtlichen Regulierungsbehörde sowie durch Anmeldung einer Vor-Ort-Gamma-
Radiographie bei der zuständigen Behörde nachvollziehbar.
+ Safety: Technische Sicherheit umschlossener radioaktiver Quellen ist gesichert durch
technische Maßnahmen.
+ Security: Öffentliche Sicherheit ist gewährleistet durch Genehmigungsverfahren, technische
24
Technische und öffentliche Sicherheit von umschlossenen radioaktiven
Quellen in der Werkstoffprüfung
Redmer et.al. DGZfP Jahrestagung 2010, Erfurt, 10.-12. Mai 2010
Regeln, Ausbildung und Training und einem entsprechenden Qualitätsmanagement.
+ Aus Sicht der nuklearen Gefahrenabwehr wird z.Z. über neue bzw. umfangreichere
Maßnahmen zur Sicherheit von umschlossenen Strahlenquellen nachgedacht. Erste Entwürfe
bei der IAEA und EU sind im Umlauf bzw. in Diskussion. Mittelfristig wird eine Änderung der
StrlSchV dazu erwartet.
To satisfy the applied compressive stresses of friction welded drive pinion fabricated by using the joint-site structure (JSS) method, three different variants were followed: (A) the initial design with two joints was carried out. Two different burn-off lengths were examined for this variant. (B) The optimum burn-off length was considered for only one weld zone. (C) The weld zone was moved radially from the initial location and two different gap sizes were compared. The smallest gap size for the third variant led to the largest weld length. The lack of structural welding defects for this variant was assessed by ultrasonic testing. Hardness of the material after friction welding (FW) was correlated to the Continuous Cooling Transformation (CCT) diagram of the used materials and revealed the phase/microstructure transformation of the material. The simulated applied stresses on the optimized friction welded design of the drive pinion showed suitable results. The new drive pinion friction welded by the JSS method reduced the weight of the component by approx. 14%.