Filtern
Erscheinungsjahr
- 2013 (18) (entfernen)
Dokumenttyp
- Vortrag (9)
- Zeitschriftenartikel (6)
- Beitrag zu einem Sammelband (1)
- Posterpräsentation (1)
- Forschungsbericht (1)
Schlagworte
- Comparability (2)
- Delta reference materials (2)
- Isotope reference materials (2)
- Mass spectrometry (2)
- Measurement uncertainty (2)
- Synthetic isotope mixtures (2)
- Traceability (2)
- Analyte-matrix separation (1)
- Archaeometry (1)
- Blei (1)
- CCQM (1)
- Fluchtafel (1)
- Herkunft (1)
- ICPMS (1)
- IDMS (1)
- Isotopenzusammensetzung (1)
- Mass discrimination (1)
- Mass fractionation (1)
- Metrology (1)
- Pb isotope ratio thermal ionization mass spectrometry (1)
- TIMs (1)
- boron (1)
- enriched isotope (1)
- isotope ratio (1)
Eingeladener Vortrag
- nein (9)
A modified Pb–matrix separation procedure using NH4HCO3 solution as eluent has been developed and validated for determination of Pb isotope amount ratios by thermal ionization mass spectrometry. The procedure is based on chromatographic separation using the Pb·Spec resin and an in-house-prepared NH4HCO3 solution serving as eluent. The advantages of this eluent are low Pb blanks (<40 pgmL-1) and the property that NH4HCO3 can be easily removed by use of a heating step (>60 °C). Pb recovery is >95 % for water samples. For archaeological silver samples, however, the Pb recovery is reduced to approximately 50 %, but causes no bias in the determination of Pb isotope amount ratios. The validated procedure was used to determine lead isotope amount ratios in Trojan silver artefacts with expanded uncertainties (k=2) <0.09 %.
The article gives a condensed version of the keynote lecture held at the International Mass Spectrometry Conference 2012 in Kyoto. Starting with some examples for isotope research the key requirements for metrologically valid procedures enabling traceable and comparable isotope data are discussed. Of course multi-collector mass spectrometers are required which offer sufficiently high isotope ratio precision for the intended research work. Following this, corrections for mass fractionation/discrimination, validation of the analytical procedure including chemical sample preparation and complete uncertainty budgets are the most important issues for obtaining a metrologically valid procedure for isotope ratio determination. Only the application of such metrologically valid procedures enables the generation of traceable and comparable isotope data. To realize this suitable isotope and/or δ-reference materials are required, which currently are not sufficiently available for most isotope systems. Boron is given as an example, for which the situation regarding isotope and δ-reference materials is excellent. Boron may therefore serve as prototype for other isotope systems.
The measurement uncertainty is an indispensable quality criterion of isotope ratio data and sets important limits for the general use and geochemical interpretation of such data. Despite traceability to the International System of Units (SI) or an accepted standard an uncertainty statement allows the direct comparison of isotope data which have been obtained in different laboratories and/or using different procedures. To realise traceability and comparability of isotope data a realistic uncertainty statements should include uncertainty contributions from all influence quantities. In isotope geochemistry, however, often the term uncertainty is used for terms describing the statistical dispersion of measurement results such as precision, repeatability or reproducibility. Because an measurement uncertainty must include all influence quantities even the so-called external precision or reproducibility will underestimate the overall uncertainty. Without uncertainty statement traceability and comparability of measurement results cannot be established. In cases where no uncertainty for isotope ratio data is presented it is highly recommended that at least the measurement results of a quality control sample with known isotope composition are presented which can be used to evaluate the accuracy and roughly estimate uncertainty.
Blei weist in der Natur die vier stabilen Isotope 204Pb, 206Pb, 207Pb und 208Pb auf, mit den entsprechenden Isotopenhäufigkeiten von 1,4%, 24,1 %, 22,1 % und 52,4 %686. Dabei sind 206Pb, 207Pb und 208Pb radiogene Isotope, welche als Endglieder der natürlichen Zerfallsreihen von 238U, 235U und 232Th entstanden sind. 204Pb ist ein sogenanntes primordiales Isotop, welches bereits vor Entstehung der Erde vorhanden war. Aufgrund dieser Prozesse weisen Gesteine, Mineralien und Erze eine charakteristische Bleiisotopenzusammensetzung auf, die von der Ausgangskonzentration an Blei, Thorium und Uran sowie von der seit der Gesteinsgenese vergangenen Zeit abhängt. Diese Eigenschaft bleibt auch während der Bleigewinnung aus dem Erz, meist Galenit, erhalten, auch wenn das Silber vorher durch Kupellation abgetrennt wurde687. Das in Silbererzen enthaltene Blei war ein willkommenes Nebenprodukt der Erzverhüttung und wurde zur Herstellung von Bleiobjekten verwendet. Artefakte, die aus dem so gewonnenen Blei gefertigt wurden, spiegeln daher die Bleiisotopenzusammensetzung der verwendeten Rohmaterialien wider.
Isotope reference materials are essential to enable reliable and comparable isotope data. Besides the correction of mass fractionation or mass discrimination, isotope reference materials are indispensible for validation and quality control of analytical procedures. This report describes the production and certification of two isotope reference materials, ERM-AE123 and ERM-AE124, for boron isotope analysis. The isotopic composition of ERM-AE123 is the unaltered natural-like isotopic composition of the base material. The isotopic composition of ERM-AE124 has been adjusted by mixing two boron stock solutions enriched in 10B and 11B respectively under full gravimetric control. All stock solutions have been prepared fully under gravimetrical control. The corresponding boron isotopic composition has been analysed by TIMS. For both reference materials the isotopic composition obtained on the basis of the gravimetric data agrees very well with the isotopic composition obtained by TIMS. The certified isotope abundances for 10B are 0.19832 (21) for ERM-AE123 and 0.96006 (6) for ERM-AE124. Together with the formerly certified ERM-AE101, -AE102a, -AE103, -AE104a, -AE120, -AE121 and AE122, a unique set of nine certified reference materials (CRM) for boron isotope analysis is now available from BAM covering a range for the 10B isotope amount fraction from 0.2 to 0.96 and for the δ11B value from -20 ‰ to +40 ‰.