Filtern
Dokumenttyp
- Zeitschriftenartikel (44)
- Vortrag (26)
- Beitrag zu einem Tagungsband (14)
- Buchkapitel (5)
- Forschungsbericht (1)
Schlagworte
- Klärschlamm (10)
- Phosphor (10)
- Phosphorus (9)
- Phosphorus recovery (9)
- Phosphorrückgewinnung (7)
- Recycling (7)
- Sewage sludge (7)
- Klärschlammasche (5)
- Wastewater (5)
- Fertilizer (4)
Organisationseinheit der BAM
- 4 Material und Umwelt (90) (entfernen)
Paper des Monats
- ja (3)
Agricultural sewage sludge utilization becomes less important in Germany. In 2017, new fertilizer and waste laws caused the agricultural sewage sludge utilization to collapse by more than a quarter. From 2029, in German wastewater treatment plants (WWTPs) phosphorus (P) must be recovered from sewage sludge ifit contains more than 2 wt % P. Agricultural utilization will be prohibited for large WWTPs > 100,000 population equivalents (pe) from 2029 and > 50,000 pe from 2032. In Germany, each federal state must annually report amounts and quality of agriculturally utilized sewage sludge which was 17 % of the total disposal in 2019. The reports of 10 States were evaluated for 2016 and 2017 representing approx. 60 % ofthe total agriculturally used sludge volume. Whereas phosphorus recovery is mandatory this does not apply to other nutrients. However, many P recovery processes recover other nutrients, too.
Considering three differentscenariosfor future German sewage sludge disposal Shows that 70 - 77 % ofthe P load in sewage sludge will probably be recovered in the future.
At the same time, this applies for about 0 - 16 % of nitrogen, 36 - 52 % of calcium, 31-53 % of potassium, and 40 - 52 % of magnesium. However, these recovered nutrient loads can substitute only 1 % or less ofthe commercial fertilizer demand except from phosphorus which is about 45 % ofthe demand.
Gypsum is widely used in the construction sector and its worldwide consumption has been increasing for several decades. Depending on the life-time of the used gypsum products, an increase of gypsum in construction and demolition waste follows. Especially against the background of a circular economy, the recycling of waste gypsum is of growing importance. However, the use of recycled gypsum makes only sense if it is environmentally friendly. Therefore, an evaluation of the environmental impacts of an industrial-scale processing for the recycling of post-consumer gypsum waste was conducted. The evaluation was performed with an established life cycle assessment software. Original data provided by industry and complementary data from a database for life cycle assessments were used for the calculations. Two scenarios for recycled gypsum with different transportation distances were calculated. These results are compared with results of the environmental evaluation of gypsum derived from coal-fired power plants (FGD gypsum) and natural gypsum. The results show that utilization of recycled gypsum can be environmentally advantageous compared to the use of natural gypsum or FGD gypsum, especially in the impact categories land transformation and resource consumption (abiotic depletion potential). For most environmental impact categories the specific transportation distances have a strong influence.
Recycled fertilizers produced using processes for the recovery of phosphate from residual materials such as wastewater, sewage sludge and sewage sludge ashes show very good bioavailability, but it is still a product largely unknown to the market. The aim of CLOOP is therefore to document the properties and effects of such fertilizers through chemical, mineralogical and ecological analyses as well as analytical method development and pot and field plant growth trials.
Outotec focused on 3 points in CLOOP: Experimental campaigns, process simulations as well as economic analyses with focus on the AshDec process, respectively the design of a large-scale AshDec plant for phosphorus recovery. The laboratory scale trials as well as the semi-industrial scale campaign provided valuable insights into the operating parameters of the process and the plant. As a result, for example, the temperature range could be significantly lowered, and the additive addition reduced by approx. 20 %. They have further shown that the AshDec process is not susceptible to operating fluctuations and that the product can be consistently produced at high quality. With the selection of suitable operating parameters, heavy metals (As, Pb, Cd, (Zn)) can be removed. Within the campaign, about 1.5 t of fertilizer for the plant trials in CLOOP could be produced. An AshDec plant process was digitally created in simulation software, allowing valuable process parameters to be simulated at various operating parameters. On this basis, a full-scale plant was designed. The data obtained in the project were used for a detailed economic analysis including a sensitivity analysis. It was possible to show under which conditions this plant can be operated economically.
At BAM, the AshDec fertilizer was synthesized with different additives and then applied to plant experiments at Uni Bonn. The goal hereby was to check differences in plant uptake. Because of the promising results of AshDec synthesized with sodium-carbonate and because this AshDec version does not require special off gas treatment for sulfur recovery (compared to AshDec synthesized with sodium-sulfate), all project partners agreed on continuing working with this AshDec variation. It was then used as a raw P-source for formulating it into NPK-fertilizers, by granulation with ammonium-sulfate and straw ash as potassium source. These recycling fertilizers were applied to plant- and field experiments by project partners in Brazil (University of Sao Paulo) and Australia (University of Queensland). Furthermore, in leaching experiments, the solubility of phosphorus in AshDec was compared to triple super phosphate. The experiments were carried out on soils with a varying phosphorus buffering index. Results show, that the phosphorus form in AshDec is way less soluble in water. This indicates that AshDec has the potential for a so-called next generation fertilizer – a fertilizer which’s nutrients remain in the soil and supply the plant according to its needs. At the moment, this behavior gets examined more in depth in lysimeter experiments in cooperation with University of Technology Berlin.
The focus of KWB is the Life Cycle Assessment (LCA) of different NextGen fertilizers to evaluate the entire process chain from recovery to fertilizer application. The NextGen fertilizer is credited by the amount of plant available nutrients in the product, which replace nutrients from conventional fertilizer. The LCA covers N-struvite precipitation from municipal wastewater, K-struvite precipitation from industrial wastewater and the AshDec-product from sewage sludge. The LCA task is almost complete. It could be shown that struvite precipitation has comprehensive environmental benefits, mainly since positive side effects occur in sewage sludge treatment (e.g. reduced sludge volume). In principle, the energetic and ecological profile of the AshDec process compared to direct use of sewage sludge ash cannot be assessed as being generally beneficial or negative. Regarding the global warming potential, the Ashdec process shows that the expenses (e.g. energy, chemicals) cannot be covered by the P fertilizer credit. In contrast, the impact categories “terrestrial acidification potential”, and “freshwater eutrophication potential” show positive results as the credits for conventional fertilizer are higher than the burdens for the process.
At University Bonn, the standardized pot experiments were conducted with several AshDec variations, using ryegrass, soybean, and spinach on a slightly acidic sandy soil and an organic-free standard substrate. P-uptake and biomass production of different AshDec variations were generally like those of triple super phosphate and struvite, and clearly outperformed untreated sewage sludge ash and rock phosphate. Field trials in Australia and Brazil with sugarcane on acidic soils are still ongoing and results are expected by the end of 2021.
Verwertung von Klärschlamm
(2018)
Die natürlichen Nährstoffkreisläufe werden durch anthropogene Einflüsse, wie das Einbringen von Schadstoffen in nährstoffreiche Stoffströme, und die ungünstige lokale Verteilung der Nährstoffe (z.B. im Zuge der Intensivtierhaltung), erheblich gestört. Es sind lokale Unter- und Überversorgungen mit Nährstoffen zu beobachten. Gelangen die Nährstoffe in Gewässer, kommt es zum bekannten Phänomen der Eutrophierung. Hierbei ist der Nährstoff Phosphat meist der limitierende Faktor und es bestehen große Bestrebungen den anthropogenen Eintrag in Fließgewässer, Seen und Binnenmeere zu unterbinden. Der Schutz der Ostsee vor Nährstoffeinträgen ist beispielsweise ein sehr wichtiges Thema geworden und wird u.a. von der Baltic Sea Action Group verfolgt.
Weitere Auswirkungen des bestehenden Systems sind Entzüge aus dem Nährstoffkreislauf, wie etwa bei der Deponierung phosphor- aber gleichzeitig auch schadstoffhaltiger Klärschlammaschen oder bei der Mitverbrennung von Klärschlamm in Müllverbrennungsanlagen, Kraftwerken oder Zementwerken. Hier wird das Phosphat ebenfalls als Bestandteil von Aschen deponiert oder in Form von Baustoffen einer sinnvollen stofflichen Nutzung entzogen. Gegen diese Art des Verlusts von Phosphat aus dem Nährstoffkreislauf hat der Gesetzgeber mit der Novellierung der Klärschlammverordnung reagiert, die am 3. Oktober 2017 in Kraft getreten ist und u.a. Regelungen zur Rückgewinnung von Phosphat aus Klärschlamm und Klärschlammasche enthält.
Klärschlämme aus kommunalen Abwasserbehandlungsanlagen ab einer genehmigtenAusbaugröße von über 100.000 bzw. über 50.000 Einwohnerwerten (EW) dürfen nach einer Übergangsfrist ab dem 1. Januar 2029 bzw. 2032 nicht mehr in der Landwirtschaft oder im Landschaftsbau verwertet werden. Die Betreiber dieser Anlagen sind zur Rückgewinnung des im Schlamm enthaltenen Phosphors verpflichtet, wenn der Klärschlamm einen Phosphorgehalt von 20 g/kg Trockenrückstand (TR) oder mehr aufweist. Für Klärschlämme mit P-Gehalten > 40 g/kg TR reicht alternativ die Absenkung der P-Konzentration um 50 % aus. Die Rückgewinnung kann aus dem Schlamm oder aus der Verbrennungsasche des thermisch vorbehandelten Klärschlamms erfolgen.
Aus der Asche müssen mindestens 80 % des Phosphoranteils zurückgewonnen werden. Anstelle einer Phosphorrückgewinnung aus Klärschlämmen aus kleineren und mittelgroßen Abwasserbehandlungsanlagen (bis 50.000 EW) können diese Schlämme auch
weiterhin zu Düngezwecken auf Böden ausgebracht werden, sofern die Anforderungen und insbesondere die Grenzwerte der Klärschlammverordnung und des Düngerechts eingehalten werden.
In der Abwasserreinigung wird der Makronährstoff Phosphor je nach Typ und Größe der Abwasserreinigungsanlage durch verschiedene Verfahren der Phosphatelimination weitgehend in die feste Phase, den Klärschlamm, überführt. Dies geschieht durch die Zugabe von Fällmitteln auf der Basis von Eisen- oder Aluminiumsalzen, oder durch das Verfahren der vermehrten biologischen Phosphorelimination (Bio-P). Das Phosphat liegt nun abhängig vom eingesetzten Verfahren als Bestandteil der gewachsenen Biomasse, als gefälltes Salz, adsorbiert an Eisen(oxi)hydroxiden oder im Falle der Bio-P Klärschlämme auch intrazellulär in Form von Polyphosphaten vor. Weitergehende Informationen hierzu sind im Beitrag von Kratz et al. Pflanzenverfügbarkeit und agronomische Effizienz von klärschlamm-basierten Phosphor (P) – Recyclingdüngern in diesem Buch zu finden. Die Bindungsformen unterscheiden sich demnach nach Art der eingesetzten Technologie der Phosphatelimination erheblich und haben einen entscheidenden Einfluss auf die verschiedenen Möglichkeiten der P-Extraktion und Rückgewinnung.
Herstellung neuer Düngemittelausgangsstoffe durch thermochemische Behandlung von Klärschlammaschen
(2018)
Klärschlammasche kann viel Phosphor enthalten (bis zu 12%). Aus diesem Grund ist diese Asche ein gutes Ausgangsmaterial für Phosphordünger. Aufgrund der geringen Pflanzenverfügbarkeit des Phosphors in der Asche ist eine Aufbereitung notwendig.
In diesem Buchbeitrag wird das thermochemische Verfahren AshDec vorgestellt, welches von dem Fachbereich 4.4 mit der Firma Outotec entwickelt worden ist. Es werden die Hintergründe diskutiert, die Phasenreaktionen bei diesem Prozess besprochen, Pflanzenversuche ausgewertet, verschiedene Extraktionen diskutiert und ein Konzept für eine mögliche Pilotanlage dargestellt.
Advantages of recycling gypsum plaster boards
During the last decades the material composition of buildings has become increasingly diverse. However, largely sorted material flows are needed for generating high quality secondary building materials. The use of secondary building materials can meet the requirements of sustainability in several ways: the extended time availability of primary raw materials and, thereby, the preservation of natural resources as well as the conservation of landfill sites.
Recycling of gypsum (calcium sulfate) can be a good example for the environmental benefits of closed-loop recycling. The content of sulfates in other secondary building materials, in particular in recycled concrete aggregates, should be minimized for quality reasons. In contrast, separated gypsum can also be used in gypsum production if the high quality requirements for the recycled gypsum are met. Since almost all processing steps in the recycling process are associated with environmental impacts, an environmental evaluation of the use of recycled gypsum as a substitute in gypsum production has to be carefully conducted.
This paper focusses on the techniques for generating recycled gypsum from gypsum plasterboards, the related quality requirements and a comprehensive environmental evaluation of the complete process.
During the last decades the material composition of buildings has become increasingly diverse. However, largely sorted material flows are needed for generating high quality secondary building materials. The use of secondary building materials can meet the requirements of sustainability in several ways: the extended time availability of primary raw materials and, thereby, the preservation of natural resources as well as the conservation of landfill sites.
Recycling of gypsum (calcium sulfate) can be a good example for the environmental benefits of closed-loop recycling. The content of sulfates in other secondary building materials, in particular in recycled concrete aggregates, should be minimized for quality reasons. In contrast, separated gypsum can also be used in gypsum production if the high quality requirements for the recycled gypsum are met. Since almost all processing steps in the recycling process are associated with environmental impacts, an environmental evaluation of the use of recycled gypsum as a substitute in gypsum production has to be carefully conducted.
This paper focusses on the techniques for generating recycled gypsum from gypsum plasterboards, the related quality requirements and a comprehensive environmental evaluation of the complete process.
Since the recycling of tantalum bearing post-consumer waste is practically not existent, metallurgical residues are the most important feed for the tantalum recycling. Most tin ores naturally contain significant quantities of refractory metals. During the smelting process in primary tin production these elements are enriched in the slag phase. This slag is a highly valuable raw material for tantalum production due to its considerable concentration of tantalum and its functioning as an additional slag former in further pyrometallurgical treatment.
In this paper the first process stage of an existing pyrometallurgical process for tantalum recovery, mainly from low grade pyrometallurgical residues, is discussed. Smelting trials were carried out in a pilot-scale electric arc furnace to analyse the effect of feeding on the activity of carbon as a reducing agent. Therefore, blowing petroleum coke through an iron lance and the manual adding of coke into the melting bath were tested. During the pyrometallurgical treatment elements with a high affinity to carbon were reduced to their carbide form and enriched in the molten iron-based metal phase. The objective of the process was to reduce the oxidic tantalum completely and to enrich it into the metal phase. Furthermore, the transfer of unwanted elements such as titanium into the metal phase was aimed to be avoided.
Spoon test specimens were taken from the liquid mineral melt to follow the evolution of the reduction process. The cooled down solidified melting bath was investigated by using the XRD and EDX method to characterise the slag system and to identify relevant mineral phases.
Blast furnace (BF) sludge and electric arc furnace (EAF) dust are typical wastes that incur from iron and steel production. In addition to iron, calcium, carbon, and silicon they usually contain high concentrations of heavy metals such as zinc, lead, and cadmium that are potentially hazardous to the environment, rendering disposal in landfills ecologically problematic and costly. Consequently, pyrometallurgical, hydrometallurgical, and hybrid methods for selective elimination of non-ferrous heavy metals from BF sludge and EAF dust have been conceived, of which only the carbothermic reduction route taken in the so-called Waelz rotary kiln process has been proven to be economically successful. However, this process has several drawbacks regarding efficiency of heavy-metal removal and recovery of iron, and it does not allow processing of BF sludge. In this study, we investigated the efficiency and feasibility of selective chlorination and evaporation of non-ferrous heavy metals, particularly zinc and lead, in both BF sludge and EAF dust as an alternative, thermochemical processing route. To this end, hydrochloric acid and iron(II) chloride solution have been used as chlorinating agents, and the process of heavy-metal chlorination and evaporation has been investigated under inert operating conditions, at variable chlorine concentrations, and at temperatures between 500 and 1200 °C.
High zinc and lead removal efficiencies of > 99.5 % were achieved with both chlorinating agents, but iron(II) chloride turned out to be overall more efficient for removal of zinc and lead from BF sludge and EAF dust. Interestingly, and in contrast to previous studies, the iron was completely retained in the processed solid residue, therefore rendering the processed residues virtually zinc- and lead-free raw materials that may either be used internally (e.g., feeding processed BF sludge and EAF dust back into the respective furnaces) or externally (e.g., for cement production).
An existing pyrometallurgical process for tantalum and niobium recovery, mainly from low grade pyrometallurgical residues, was investigated. Series of melting experiments were carried out in a pilot-scale electric arc furnace to study how the amount, the grain size and the way of feeding affect the activity of carbon as a reducing agent. During the pyrometallurgical treatment refractory metals such as tantalum and niobium are reduced to their carbide form and enriched in the molten iron-based metal phase. The cooled down slag and metal phase were analysed to investigate thermodynamic and kinetic conditions of the carbide formation. FACT Sage simulations were also used to investigate the material system in state of thermodynamic equilibrium. Results show that mass transfer and kinetics may play an important role if compared to equilibrium analyses using FACT Sage.