Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (21)
Sprache
- Englisch (21) (entfernen)
Referierte Publikation
- ja (21) (entfernen)
Schlagworte
- Cellular polypropylene (3)
- Electrostriction (2)
- Ferroelectret (2)
- Ferroelectrets (2)
- Non-contact transducers (2)
- Phased array (2)
- Ageing effects (1)
- Air borne transducer (1)
- Air coupled ultrasonics (1)
- Air-coupled ultrasonics (1)
The development of non-destructive techniques (NDT) techniques for the in-service inspection of railroad wheels and gauge corners was the main activity of the NDT division VIII. 4 at BAM over the last 2 years. For such different components, two different inspection techniques were fundamentally chosen in order to fulfil the end-user requirements. Firstly the inspection of the wheelsrim and diskshould be carried out without dismantling the wheels and using ultrasonic techniques. On the other hand, the inspection of the railroad track surface at a train speed of about 70 km/h should be guaranteed using eddy current techniques. The above-mentioned tasks were a challenge for the lab staff. The accessibility for the wheel inspection was limited due to several impassable barriers such as sand tubes, etc. Eddy current application focused mainly on the detection of head check defects occurring at the gauge corner of the rail. Investigations carried out also showed, that other types of surface defects (e.g. Belgrospis, wheel burns, short-pitch corrugations, etc.) could easily be detected. Some aspects of the inspection system as well as an overview of test results are presented in the current contribution.
In general, the application of phased array techniques used to be limited to heavy components with large wall thicknesses, such as those in the nuclear power industry. With the improvement of the phased array equipment, including phased array search units, other application areas are now accessible for the phased array inspection technique, e.g. the inspection of turbine blade roots, weld inspection with a wall thickness ranging from 12 to 40 mm, inspection of aircraft components, inspection of spot welds and the inspection of concrete building components. The objective for the use of phased array techniques has not significantly changed since their first application, e.g. instant adjustment of the sound beam to the geometry of the test object by steering incidence angle, skew angle and/or sound field focusing. Because some new phased array technique applications are still in the experimental (laboratory) stage, this article will focus on some examples for practical, real-weld applications.
Steam generator (SG) tubes are part of the primary circuit of pressurised water reactors and therefore also part of the pressure retaining boundary components. Furthermore, steam generator tubes are the components which guarantee the separation between the primary and secondary circuits. Therefore the knowledge of the loss of tube integrity as soon as possible is an essential. Optimised nondestructive testing methods based on the eddy current array technique are used to find material degradation, especially intergranular stress corrosion cracks during the periodical in-service inspection. These methods are supported by the measurement of the leakage rate during operation based on radioactivity and Tritium measurement regarding a high crack grows. Shutdown criteria depending on leakage rates which are described in the operation procedures but there are no specifications about the conditions for the measured leakage. Is the leakage coming from a single crack or are there multiple cracks or is this the leakage of a critical crack. With the help of FE calculations answer about the uncertainties of leakage rate versus critical crack grows were found. Shutdown criteria must guarantee to avoid critical crack sizes, i.e. between the measured tritium activity and the critical crack size must be a safety gap.
Polypropylene based ferroelectret films exhibit a strong electromechanical activity and provide a promising solution for the air coupled ultrasonic (ACUS) transducers. Ultrasonic transmission between two air coupled ferroelectret transducers in dependence on the amplitude and polarity of the high voltage exciting pulse revealed a strongly non-linear electromechanical response of the ferroelectret transmitter which provides an increase in the transmitter efficiency. The authors present a simple model describing both promotion and competition of the piezoelectric and electrostriction contributions, as well as increase in the transducer constant under high voltage excitation. Enlargement of the inverse transducer constant of the polypropylene ferroelectret film by a factor of 4 was demonstrated. The non-linear properties of the polypropylene ferroelectrets result in a strong increase in their ACUS figure of merit under the high voltage excitation, which exceeds the results of their technological optimisation. Consequently, enhancement of the ACUS system transmission by 12 dB and signal to noise ratio by 32 dB was achieved.
Analysis of the dielectric and electromechanical properties of the cellular polypropylene ferroelectret films (EMFIT) evidences their high potential for the application in the air-coupled ultrasonic transducers. Simple prototype transducers, based on the EMFIT films, were developed and their high sensitivity was proved in the air-coupled ultrasonic experiment. Amplitude and delay time scanned images of the polyethylene step wedge with holes, obtained in both pulse-echo and transmission modes, demonstrate that non-contact ultrasonic imaging with EMFIT transducers is possible.
Dielectric and electromechanical properties of the cellular polypropylene ferroelectret films (EMFIT), combining strong piezoelectric response with a low density and softness, evidence their high potential for the air-coupled ultrasonic applications. The disadvantage of the low coupling factor is compensated by the extremely low acoustic impedance, which provides excellent matching to air and promises efficient sound transmission through the airtransducer interface. The influence of the electrodes on the electromechanical properties was investigated. Electron beam evaporation technology was adapted to the EMFIT films, and films with both-sided Au and Al electrodes were prepared without reducing or suppressing of the electromechanical properties. Finally, prototype transducers based on the EMFIT films were developed. In spite of the simple construction and absence of matching layers, high sensitivity of the EMFIT transducers was proved in the air-coupled ultrasonic experiment. Amplitude and delay time scanned images of the polyethylene step wedge with holes, obtained in both pulse-echo and transmission modes, demonstrate that non-contact ultrasonic imaging and testing with EMFIT transducers is possible.
The comparison of probes for the inspection of cladding shows a remarkable fact: depending on the reflectors used, a different performance characterization of the probe must be expected. It seems important for performance demonstration trials - especially those including the underclad area - to use reflector types as close as possible to the real cracks to be detected. For different detection approaches, reflectors representing underclad cracks should have a reduced diffraction at the crack tip areas in order to check their potential to detect the indication based on surface reflections of the ultrasonic waves.