Filtern
Erscheinungsjahr
- 2020 (7) (entfernen)
Dokumenttyp
- Zeitschriftenartikel (7) (entfernen)
Sprache
- Englisch (7)
Schlagworte
- Bogie´s yaw friction (1)
- Bogie´s yaw stiffness (1)
- Carburizing (1)
- Centre plate (1)
- Decarbonization (1)
- Drag resistance (1)
- Driving style (1)
- Dry friction (1)
- Energy efficiency (1)
- Energy losses in transportation (1)
Organisationseinheit der BAM
CCQM-K143 is a key comparison that assesses participants’ ability to prepare single element calibration solutions. Preparing calibration solutions properly is the cornerstone of establishing a traceability link to the International System of Units (SI), and therefore should be tested in order to confirm the validity of CCQM comparisons of more complex materials. CCQM-K143 consisted of participants each preparing a single copper calibration solution at 10 g/kg copper mass fraction and shipping 10 bottled aliquots of that solution to the coordinating laboratory, the National Institute of Standards and Technology (NIST). The masses and mass fraction for the prepared solutions were documented with the submitted samples.
The solutions prepared by all participants were measured at NIST by high performance inductively coupled plasma optical emission spectroscopy (HP-ICP-OES). The intensity measurements for copper were not mapped onto values of mass fraction via calibration. Instead, ratios were computed between the measurements for copper and simultaneous measurements for manganese, the internal standard, and all subsequent data reductions, including the computation of the KCRV and the degrees of equivalence, were based on these ratios. Other than for two participants whose measurement results appeared to suffer
from calculation or preparation errors, all unilateral degrees of equivalence showed that the measured values did not differ significantly from the KCRV. These results were confirmed by a second set of ICP-OES measurements performed by the Physikalisch-Technische Bundesanstalt (PTB). CCQM-K143 showed that participants are capable of preparing calibration solutions starting from high purity, assayed copper metal.
Similar steps are involved when preparing solutions for other elements, so it seems safe to infer that similar capabilities should prevail when preparing many different, single-element solutions.
Different approaches have been attempted so far to reduce fuel consumption and linked pollutants, including vehicle equipment and design, with rational driving style being recognized as a potential source of fuel savings. However, no specific methodology had been suggested so far to assess fuel economy of driving other than the fuel consumed itself. In this paper, the Standard deviation of driving acceleration has been found to be directly associated to fuel consumption, so that the less dispersion of the driving acceleration, produces the lower fuel consumptions and emissions. Such metric could be thus used to assess driving style.
Wheel forces generate stresses in the rail as a function of several vehicle and infrastructure characteristics and operating conditions. The different components of the wheel forces develop strains in the rail which contain an elastic and hysteretic (irreversible) components. The irreversible deformations of the rail would be associated with locomotive energy losses. In this paper, a testing facility is proposed to indirectly characterize the level of stresses in the rail, in terms of the energy that is lost during tuming maneuvers. Different potentially influential factors are considered, including the friction at the Center plate, the wheelbase length, the distance between bogies and the radius of the curved track. The change
in the potential energy during a U-turn displacement is measured. In this respect, an experimental model under this operating principle, aimed at validating such a principle of Operation, reveals a significant effect of the friction at the center plate on the energy lost during turning maneuvers, and consequently, on the level of stresses in the rail.
In spite that transport activities do not represent the biggest contributor of pollutants emissions, their reduction has been a priority as some other externalities are associated to such emissions and to the transport itself. A crucial element to characterize the behavior of the vehicles against the environment are the losses that such vehicles exhibit in a passive way, that is, without any involvement of power conditions. The energy loses due to the rolling, the drag and to the friction in mechanical components, have been assessed so far in terms of the stopping acceleration when the vehicle idles on a ramp. However, such a testing procedure produces some uncertainties due to the dynamic conditions that are considered. To avoid such critical limitations, in this paper a testing procedure and facility are proposed, which are based on static conditions of the vehicle at the initiation and at the ending of the test, which are assumed to provide a better reliability to the testing. Some preliminary theoretical analysis should be made in order to validate the operational principles proposed herein for such testing facility.
Turning maneuvers originate higher forces exerted on the rail and the loss of locomotive energy, at a rate that is function of several parameters that influence the magnitude of the developed horizontal wheel-rail forces, including the friction at the centre plate and the bogie´s yaw stiffness. However, such a friction at the contact surfaces of the centre plate is needed to mitigate the Hunting phenomenon when the train moves on straight track segments. In this paper, a self-centering centre plate is proposed, consisting of a lubricated centre plate, equipped with a spring- and damper-based self-centering mechanism. Simulation results of the proposed mechanism suggest that the energy performance in turns of a train car equipped with such self-centering centre plate is comparatively better, as the peak friction forces linked to the dry friction at the contact surfaces of current centre plate designs, are avoided. The assessment of the hunting performance of the proposed device in straight track segments is proposed as the continuation of this work.
A facility is proposed in this paper to apply a selective carburizing process to the lateral faces of a railways´ head, aiming to increase its carbon content and to decrease the friction coefficient in case that the flange of the railway car wheel gets in contact with the rail during turning. Such a treatment would reduce the energy that is lost during the turning maneuvers performed by the vehicle, further improving the energy efficiency of the railway car. The facility consists of a furnace, which should be set next to the rails´ hot-rolling facility, in order to use the available enthalpy. The proposed furnace is equipped with what is necessary to avoid the decarbonization of the remaining rail material, based upon batteries of oxy-acetylene burners that are installed at the bottom of the furnace, on the opposite side to the carburizing surface. An experimental facility is necessary to validate the operational principles for the equipment proposed in this paper. On the other hand, a study should also be carried out to assess the effect of any rail welding process on the carburized surfaces.
Vehicle’s components damage
(2020)
The failure of vehicle’s suspension components has contributed to road crashes, while their defective operation can deteriorate the fuel efficiency of the vehicles. In this context, and when compared with solid cargo transporters, the road tankers would tend to produce larger roll forces during turning, as the curved shape of the liquid cargo container, shifts upwards the centre of gravity of the cargo. With reference to a rectangular cargo container representing the solid cargo situation, the increase in the position due to elliptical and circular tank shapes, can attain a value of 17% (100% fill, circular tank). In this study, experimental results comparing the lateral load transfer due to solid and liquid cargoes, indicate that the average force increase on the vehicle’s load-receiver side due to a liquid cargo, is 4.3%. To analyse the fullscale situation of both situations, that is, the higher position of the centre of gravity and the shifting of the liquid cargo, a simplified model is developed. The outputs from such a model when subjected to realistic operating conditions (speed
and turning radius), suggest that the higher position of the centre of gravity due to using a non-rectangular cargo container generates an average force increase of 4.9% on the side receiving the load transfer. The incorporation of the effect of the liquid cargo, through the simple pendulum analogy, suggests that such an average increases to 6.76%, with a maximum of 8.35% in the case of the elliptical tank at 75% fill level. It is found that the average liquid cargo effect is 5.44%, which should be compared with the 4.3% of the experiments. Road tankers components would thus have a relatively shorter load cycle life than those of the solid cargo trucks.