Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (17)
- Deutsch (13)
- Mehrsprachig (1)
Schlagworte
- Ductile cast iron (6)
- Dynamic fracture toughness (3)
- Fracture mechanics (3)
- Monitoring (3)
- Schallemission (3)
- Acoustic emission (2)
- Beschleunigungssensoren (2)
- Faseroptische Sensorik (2)
- Rohrleitung (2)
- Abgasturbolader (1)
- Absorbed energy (1)
- Accelerometer (1)
- Accelerometers (1)
- Accoustic emission (1)
- Achsschenkel (1)
- Acoustic emissions (AE) (1)
- Alterung (1)
- Analysis procedure (1)
- Axial Compression (1)
- Axial compression variation (1)
- Bending tests on pipe segments (1)
- Bewertung (1)
- Bruchmechanische Auslegung (1)
- CTOD (1)
- Charpy pendulum impact test (1)
- Component (1)
- Containment (1)
- Continous monitoring (1)
- Conversion of results (1)
- Crack (1)
- Crack growth (1)
- Crack initiation (1)
- Crack initiation toughness (1)
- Crack resistance curve (1)
- Curve fitting (1)
- Cyclic load (1)
- Cycling Tests (1)
- DCI (1)
- Dichtheit (1)
- Distributed acoustic sensing (1)
- Dynamic fracture mechanics (1)
- Dynamic loading (1)
- Dynamischer Zugversuch (1)
- Fail-safe (1)
- Federunterstützte Metalldichtungen (1)
- Fiber optic sensing (1)
- Fibre optic acoustic sensing (1)
- Fibre optic sensing (1)
- Finite element simulation (1)
- Fließkurve (1)
- Four-point bending test (1)
- Fracture (1)
- Frequency domain (1)
- Frequenzanalyse (1)
- Graphite morphology (1)
- Helium Leakage Rate (1)
- Helium leakage rate (1)
- Helium-Dichtheitsprüfung (1)
- Hochgeschwindigkeitsversuch (1)
- J-integral (1)
- Kerbschlagarbeit (1)
- Kerbschlagbiegeversuch (1)
- Kerbschlagbiegeversuch, Untermaßproben, Normalproben, Skalierung von Ergebnissen (1)
- Korrelation (1)
- Langzeitversuche (1)
- Large scale test (1)
- Leak detection (1)
- Leckage (1)
- Leckagerate (1)
- Loading rate (1)
- Loading rate effect (1)
- Low blow (1)
- Messtechnik (1)
- Metal Seals (1)
- Metal seals (1)
- Microstructure (1)
- Monitoring von Rohrleitungen (1)
- Pipeline monitoring (1)
- Pipelines (1)
- Potential drop technique (1)
- Product standard (1)
- R-curve (1)
- Rissbildung in Stahl (1)
- Rohrbiegeprüfstand (1)
- Schadensursachen an Rohrleitungen (1)
- Seal effects (1)
- Spannungs-Dehnungskurve (1)
- Specimen geometry (1)
- Specimen size effect (1)
- Standard test piece (1)
- Statistical analysis (1)
- Steel (1)
- Steel pipe (1)
- Structural integrity (1)
- Structural integrity assessment procedure (1)
- Sub-size test piece (1)
- Test standard (1)
- Test temperature (1)
- Testing (1)
- Transition temperature (1)
- Transport- und Lagerbehälter für radioaktive Stoffe (1)
- Untermaßproben (1)
- Verteilte Faseroptische Sensorik (1)
- Werkstoffprüfung (1)
Organisationseinheit der BAM
- 9 Komponentensicherheit (9)
- 9.6 Additive Fertigung metallischer Komponenten (7)
- 2 Prozess- und Anlagensicherheit (6)
- 2.1 Sicherheit von Energieträgern (6)
- 8 Zerstörungsfreie Prüfung (6)
- 8.1 Sensorik, mess- und prüftechnische Verfahren (6)
- 3 Gefahrgutumschließungen; Energiespeicher (4)
- 3.2 Gefahrguttanks und Unfallmechanik (3)
- 8.4 Akustische und elektromagnetische Verfahren (3)
- 8.6 Faseroptische Sensorik (3)
Der Kerbschlagbiegeversuch ist seit der ersten Hälfte des letzten Jahrhunderts standardisiert und seit langem als Prüfverfahren international genormt. Weltweit sind zu garantierende Werte der Kerbschlagenergie (KV) und Übergangstemperaturen (TÜ) in Produktnormen und Regelwerken festgelegt. Unter bestimmten Bedingungen besteht dabei die Option, statt Normalproben Untermaßproben zu prüfen. Im Rahmen einer Untersuchung der BAM wurde der aktuelle Status von Prüf- und Produktnormen sowie Regelwerken zur Bewertung der Bauteilintegrität hinsichtlich ihres Umgangs mit Untermaßprobenergebnissen erfasst. Zur Schaffung einer geeigneten aktuellen Datenbasis wurden an ISO-V-Proben der Dicken 2,5, 5,0, 7,5 und 10,0 mm aus vier aktuellen Baustählen KV2-T-Kurven ermittelt. Es wurden unterschiedliche Vorgehensweisen zur Kurvenanpassung und Festlegung von Übergangstemperaturen praktiziert. Ferner kamen verfügbare Ansätze zur Skalierung von Untermaßprobenergebnissen auf die Werte von Normalproben zur Anwendung. Das Ausmaß des Probendickeneffektes ist werkstoff- und temperaturabhängig. Im Bereich der Werkstoffprüfung ist akzeptiert, dass die Ergebnisse von Normal- und Untermaß-proben nicht ohne Weiteres ineinander überführt werden können. Der Stand der Produktnormung und der Regelwerke ist jedoch im besten Falle als unzureichend, vielfach jedoch schlicht als falsch zu bezeichnen. In einem weiten anwendungsrelevanten Temperaturbereich werden hier sogar deutlich nicht-konservative Skalierungsergebnisse geliefert. Die betroffenen Produkt-normenreihen und Regelwerke müssen überarbeitet werden.
Der Kerbschlagbiegeversuch ist als Prüfverfahren seit langem international genormt. Zu garantierende Kerbschlagarbeitswerte sind in Produktnormen weltweit festgelegt. Gleichwohl enthalten ganze Normenreihen für Stähle falsche Festlegungen zur Verwendung von Untermaßprobenergebnissen. Im Mittelpunkt der vorliegenden Studie stehen die Auswertung von KV-T-Daten und die Skalierung von Untermaßprobenergebnissen. Hierzu wurden an ISO-V-Proben der Breiten 2,5; 5; 7,5 und 10 mm aus vier Baustählen im Streckgrenzenbereich von 235 bis 960 MPa dicht belegte KV-T-Kurven ermittelt. Es wurden unterschiedliche Vorgehensweisen zur Kurvenanpassung und Festlegung von Übergangstemperaturen wie auch der Hoch- bzw. Tieflagenarbeit untersucht. Die Ergebnisse unterstreichen unter anderem, dass die in festgelegte Vorgehensweise, nach der Untermaßprobenergebnisse proportional auf Normprobenmaße zu skalieren sind, nicht nur zu falschen, sondern auch nicht-konservativen Kerbschlagarbeitswerten führen kann. Das Ausmaß dieses Probenbreiteneffektes ist Werkstoff- und temperaturabhängig. Da die Kerbschlagarbeit als Abnahmekriterium verwendet wird, ergeben sich unmittelbare wirtschaftliche und sicherheitstechnische Konsequenzen. Es ist zu schlussfolgern, dass die entsprechenden Produktnormenreihen dringend zu überarbeiten sind.
Fracture mechanics based component design requires appropriate fracture mechanics toughness data with respect to both, loading rate as well as test temperature. Taking high-rate loading into account such as with accidental scenarios, different standards such as ASTM E 1820 or BS 7448-3 provide some information on dynamic fracture mechanics testing. Nevertheless, the designations differ so that a validation of the own material specific test method used for dynamic R-curve determination is mandatory. In order to address this for ductile cast iron materials an experimental method for the reliable determination of dynamic J-integral crack resistance curves at -40 °C following the multiple specimen approach has been established and validated. The experimental concept offers some additional valuable features. Single values of dynamic crack initiation toughness can be determined using a single specimen technique based on crack sensors. Furthermore, an experimentally independent method is provided according to which CTOD δ5 R-curves can be established. The focus of the present paper is on the validation of the experimental low blow technique using a drop tower test system.
A drop tower test system was developed and set up to perform low blow tests at temperatures down to -40 °C. The system allows for a variation of the impact mass and height and was optimized for testing of ductile cast iron at stress intensity rates from approximately 5∙10⁴ to 3∙10⁵ MPa√ms⁻¹. This range of loading rate is characteristic for instance with crash scenarios of heavy sectioned DCI casks for radioactive materials. In order to address characteristic challenges of impact tests (test duration of microseconds up to milliseconds, inertial effects, signal oscillations), an appropriate full bridge strain gage method for the measurement of force directly on the specimen as well as a non-contact measurement of load line displacement using an optical extensometer have been developed and validated.
The low blow test requires either to prevent bouncing strikes of the hammer by using the stop block technique or to catch the hammer after its first strike. Both options are not part of the experimental concept and setup which have been realized here. The paper describes investigations which have been performed in order to make sure that bouncing strikes of the hammer do not cause additional crack extension in the specimen. This is necessary to ensure a unique relation between the work done and the achieved crack extension. The investigations covered the analysis of limit loads of the specimen with respect to the measured force. The measured stiffness of the specimen was assessed and signals of crack sensors were analyzed. Furthermore, an analysis of the mechanical behavior of the loading system and the specimen by optical observation was performed. Corresponding results are discussed in the paper. It had finally been proven that additional crack extension in the specimen due to bouncing strikes of the hammer is not to be expected under the given conditions of test setup, material and loading. It can be seen as a major experimental advantage that the striker does not have to be catched after the low blow test.
This paper is focused on the approximation of absorbed Charpy impact energy-temperature curves (KV-T) and the management of sub-size test piece results in Charpy pendulum impact tests. Both subjects are frequently underestimated but may have a strong impact on the assessment of product quality and structural integrity. The status of related test standards, product standards, structural integrity assessment procedures and corresponding research is reviewed.
It is concluded that the state of regulation is partly insufficient and wrong. There is a wide gap between the state of knowledge in the field of materials testing and the requirements of product standards and structural integrity assessment procedures. The present paper aims at boosting and supporting the necessary discussion among the parties involved to raise the level of technical safety. Correspondingly, a large experimental database was created by Charpy impact testing of popular modern structural Steels with nominal yield strength from 235 MPa to 960 MPa. KV-T data were generated using test pieces with thicknesses between 2.5 mm and 10 mm. Different strategies for KV-T curve fitting, definition of transition temperatures, as well as upper and lower shelf energy levels were followed, and different scaling procedures were applied to the sub-size test piece results. The results show that proportional scaling of sub-size to full-size test piece results in terms of KV should be disallowed because it is a wrong approach.
Regulations still incorporating such procedures should be revised as soon as possible. Existing nonproportional scaling and conversion procedures were applied. The results obtained illustrate that neither an overall nor consistent conservatism nor an adequate conservatism level can be achieved. In summary, the standardizing bodies should enforce the discussion to revise relevant test standards considering more precise specifications on Charpy data fitting. Furthermore, proposals are made for an improved management of sub-size test piece results.
Four-point bending tests were carried out to analyze the acoustic characteristics of damage development in pipe segments made of steel, grade S355J2H, being 2.5 m long with an outer diameter of 168 mm and 16 mm wall thickness. To induce stable crack growth, the pipe segments were pre-damaged by a 90°circumferential notch in the middle of the pipe length. While the pipe was quasi-statically loaded, microscopic damage and plastic deformation accumulated to form a macroscopic crack that grew through the pipe wall until leakage. For acoustic emission (AE) monitoring, four broadband sensors of type VS 900 M were mounted close to the notch. Continuous AE signal detection was performed by the non-threshold method. Advantages and disadvantages of the non-threshold AE monitoring compared to a commonly employed method analyzing only signals exceeding a predefined threshold are discussed. The results of AE analysis are compared to additional information on the crack growth detected by the direct current potential drop (DCPD) technique. These studies were carried out in the course of the interdisciplinary research project AGIFAMOR, Ageing infrastructures - distributed acoustic monitoring of pipes at BAM.
The monitoring of oil and gas pipelines by means of distributed fibre optic sensors is becoming common. The most recent development in the field of fibre optic sensing is the distributed acoustic sensing (DAS), which allows to detect and to localize third party threats to pipelines. For this purpose, fibre optic telecommunication cables located close to the pipelines are usually used. However, DAS carries a far greater potential for continuous condition monitoring of pipelines.
The interdisciplinary research project AGIFAMOR (Ageing Infrastructures – Fibre Optic Monitoring of Pipes) at BAM investigates a new technical approach to extend the application field of DAS towards the detection and localization of acoustic signals that indicate critical alterations and certain damage scenarios originated from within the pipeline or the pipe wall. Therefore, the optical fibre sensors are applied onto the pipe itself and the application procedure towards an optimal acoustic signal transduction is optimized.
A number of laboratory scale experiments were performed focusing on the signal transmission of acoustic signals as well as the detection of damages in the pipe wall by means of DAS. Furthermore, real-scale tests on a pipeline DN100 of 38m length have been carried out at the BAM test site for technical safety (BAM-TTS) to study the detection and localization of leaks and of changing flow profiles due to corrosion or sedimentation processes.
Large scale testing and statistical analysis of dynamic fracture toughness of ductile cast iron
(2009)
Langzeitversuche über 10 Jahre an Federkern-Metalldichtungen mit Aluminium- bzw. Silberummantelungen
(2023)
Federunterstützte Metalldichtungen mit Aluminium(Al)- oder Silber(Ag)-Ummantelung werden u.a. in Behältern für Wärme entwickelnde radioaktive Abfälle eingesetzt, da diese Dichtungen eine sehr gute Dichtheit gewährleisten sowie Langlebigkeit und Beständigkeit gegenüber erhöhten Temperaturen und radioaktiver Strahlung aufweisen. Auch wenn die Sicherheit solcher Behälter und der verwendeten Dichtungen vielfach belegt wurde, sind sie Gegenstand andauernder Forschung, etwa im Hinblick auf eine absehbar benötigte verlängerte Zwischenlagerdauer. Aus diesem Grund werden an der Bundesanstalt für Materialforschung und -prüfung (BAM) im Fachbereich 3.4 „Sicherheit von Lagerbehältern“ seit über 20 Jahren Versuche an solchen Metalldichtungen durchgeführt. Dabei sollen zusätzliche Erkenntnisse hinsichtlich der Sicherheitsreserven der Dichtungen in unterstellten Störfallszenarien (axiale Bewegung des Deckelsystems bzw. Aufweitung der Nutgeometrie) und insbesondere detailliertere Erkenntnisse zum Langzeitverhalten gewonnen werden.