Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (43)
- Vortrag (7)
- Beitrag zu einem Tagungsband (5)
- Beitrag zu einem Sammelband (3)
- Posterpräsentation (3)
- Forschungsbericht (3)
Schlagworte
- ToF-SIMS (14)
- XPS (13)
- Nanoparticles (5)
- Surface analysis (5)
- Auger electron spectroscopy (4)
- CCQM (4)
- CIGS (4)
- Microarrays (4)
- Oberflächenanalytik (4)
- AES (3)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (7)
Glühentladung optischer Ausstrahlungsspektroskopie (GDOES) wurde ursprünglich für die elementare Analyse von Größenmaterialien entwickelt. Mehrere Gruppen führten diese Methode zur Analyse von Anstrichen, Laienstapeln und dünnen Filmen durch. In den frühen Neunzigern wurde eine ISO-TC 201-Arbeitsgruppe gegründet, um Normen für alle Formen der Glühentladungsspektroskopie (GDS) zu entwickeln und die Fähigkeiten der Oberflächenchemikalien-Analyse zu beurteilen, insbesondere für die Tiefe von gestuften Systemen. Die Quantifizierung von Tiefenprofilen, d.h. die Umwandlung von Intensitäts-Zeit- Profilen in Konzentrierungs-Tiefen-Profile ist für dc-mode entwickelt worden. 1997 wurde ein VAMAS TWA 2 Vorschlag für ein Referenzanstrich für GD-OES Tiefe gemacht. Entsprechend dem VAMAS Beurteilungsverfahren wurde dieser Vorschlag 1998 mit einigen geringfügigen Änderungen genehmigt.
Imaging ToF-SIMS has been applied to characterize the surface chemistry variations across small areas produced by a DBD-type plasma printing technique on a BOPP substrate using pure nitrogen and a nitrogen-hydrogen gas mixture. CH4N+ and CNO- secondary ions are detected with high yields remote from the discharge region. They are discussed to be due to surface modifications of the substrate by metastable gas-phase species. On the other hand, surface species exist that are preferentially formed by reactions of the substrate with short-lived species which are only present close to the plasma discharge region. A C3H8O+ secondary fragment ion is assumed to be a key fragment of such a surface species.
In the present work, the influence of deuterium on the microstructure of a duplex stainless steel type EN 1.4462 has been characterized by Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS) supported by scanning electron microscopy (SEM), focused ion beam (FIB), electron back scattered diffraction(EBSD) and energy dispersive x-ray (EDX) investigations. Characterization has been carried out before and after electrochemical charging with deuterium which has been used as a tracer, due to its similar behavior to hydrogen in the steel microstructure. In a first approach, the distribution of the deuterium occurring at temperatures above 58 °C has been visualized. Further it turned out that sub-surface micro blisters are formed in the ferrite-austenite interface, followed by the formation of needle shaped plates and subsequent cracking at the ferrite surface. In the austenite phase, parallel cracking alongside twins and hexagonal close packed (martensitic) regions has been observed. In both phases and even in the apparent interface, cracking has been associated with high deuterium concentrations, as compared to the surrounding undamaged microstructure. Sub-surface blistering in the ferrite has to be attributed to the accumulation and recombination of deuterium at the ferrite-austenite interface underneath the respective ferrite grains and after fast diffusing through this phase. Generally, the present application of chemometric imaging and structural analyses allows characterization of hydrogen assisted degradation at a sub-micron lateral resolution.
Recently, time-of-flight secondary ion mass spectrometry (ToF-SIMS) and X-ray photoelectron spectroscopy (XPS) instrumentation has been used to address areas of interest within micro-fluidic devices providing full access to the surface chemistry established at the bottom of micro-channels therein. After careful calibration, information on surface chemistry as obtained by ToF-SIMS or XPS can be interpreted in terms of wettability expressed as contact angles which are then characteristic for the inner walls of micro-channels. Standard contact angle measurement is not applicable in micro-channels. The approach has been demonstrated to be successful with two different micro-fluidic devices hot embossed into high-end quality poly(methyl methacrylate) (PMMA) or Polycarbonate wafers. A pre-selected surface chemistry at micro-channel walls can be established by plasma technologies but ageing and rinsing effects have to be under control. A combination of ToF-SIMS, XPS and contact angle measurement techniques has been demonstrated to provide the required information. Finally, it is shown by ToF-SIMS and XPS analysis that in the production of micro-fluidic parts during practical processing using hot embossing technologies, material originating from cover foils will reside on the polymer wafer's surface. Moreover, residues of releasing agents as silicone oil used during processing can be detected by ToF-SIMS. Both cover foil residues and silicones are issues of trouble shooting in micro-fluidics because they will change contact angles efficiently.
Microarrays are a versatile platform for diagnostics and high-throughput analysis. Carbohydrate microarrays are valuable tools to investigate interactions with other molecules since many glycans are involved in fundamental biological processes. A combined X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS) surface analysis was used to investigate the basic steps in the production of carbohydrate microarrays. The preparation included coupling of a thiol-terminated mannoside to maleimide-functionalized glass surfaces derived from γ-aminopropyl silane (GAPS) slides. XPS results clearly demonstrate successful chemical modification in each fabrication step, and ToF-SIMS imaging revealed immobilized carbohydrates in the spotted regions of the final microarray.