Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (46)
- Mehrsprachig (2)
Referierte Publikation
- ja (48) (entfernen)
Schlagworte
- Microstructure (8)
- Creep (5)
- Aging (4)
- Fatigue (4)
- Additive Manufacturing (3)
- Cast iron (3)
- Residual stress (3)
- AGIL (2)
- AISI 316L (2)
- Additive manufacturing (2)
- Aluminum alloys (2)
- Cyclic softening (2)
- Elasticity (2)
- Electron microscopy (2)
- Fatigue damage (2)
- GMR (2)
- Metal magnetic memory (2)
- Number density (2)
- Ontologies (2)
- Ostwald ripening (2)
- P92 (2)
- Phase-field simulation (2)
- Plastic deformation (2)
- Precipitation (2)
- S-Phase (2)
- Stress relaxation (2)
- Tempered martensite-ferritic steel (2)
- Tensile strength (2)
- Thermo-mechanical fatigue (2)
- Thermomechanical fatigue (2)
- Ti-6Al-4V (2)
- Volume fraction (2)
- 316L (1)
- 9-12%Cr steel (1)
- Accessible (1)
- Acoustic emission (1)
- Advanced ceramic (1)
- Age hardening (1)
- Al-Cu alloy (1)
- Al-Cu-Li-alloy (1)
- Aluminum alloy (1)
- Al‐Cu‐Li‐alloy (1)
- Anisotropie (1)
- Automated image analysis (1)
- Axial-torsional Loading (1)
- Axial-torsional loading (1)
- Bitter technique (1)
- Brinell hardness (1)
- CKAN (1)
- Carbon capture and storage (CCS) (1)
- Casting skin (1)
- Ceramics (1)
- Characterisation (1)
- Chemo-mechanical coupling (1)
- Computed Tomography (1)
- Corrosion behaviour (1)
- Cracks (1)
- Creep behavior (1)
- Creep strength (1)
- Creep testing (1)
- Creep-fatigue (1)
- Creep-fatigue interaction (1)
- Crystal plasticity (1)
- Damage (1)
- Damage analysis (1)
- Data Interoperability (1)
- Data infrastructures (1)
- Data mapping (1)
- Deformation (1)
- Differential scanning calorimetry (DSC) (1)
- Digital image correlation (1)
- Digital representations (1)
- Digital workflows (1)
- Digitalizations (1)
- Domain Ontology Development (1)
- Dwell periods (1)
- Dwell times (1)
- EN AW-2618A (1)
- Elastic modulus (1)
- Elastische Energie (1)
- Emission coefficient (1)
- Environment (1)
- Expanding cavity model (1)
- FAIR (1)
- FAIR Data Management (1)
- FAIR research data management (1)
- Fatigue assessment (1)
- Fatigue life time (1)
- Fatigue testing (1)
- Ferritic–martensitic steel (1)
- Fossil fuel power plants (1)
- Fracture (1)
- Fraktographie (1)
- Gamma titanium aluminide (1)
- Gamma-Titanium Aluminide (1)
- General Computer Science (1)
- General Engineering (1)
- General Materials Science (1)
- Growth kinetics (1)
- Hall-Petch relationship (1)
- Heat resistant steels (1)
- Heat treatment (1)
- High Cycle Fatigue (HCF) (1)
- High efficiency power plants (1)
- Hocheffiziente Kraftwerke (1)
- IN 718 (1)
- In-situ Process Monitoring (1)
- Inconel 718 (1)
- Indentation (1)
- Industrial and Manufacturing Engineering (1)
- Interfacial anisotropy (1)
- Interoperable (1)
- Isothermal fatigue (1)
- Knowledge Representation (1)
- Knowledge graphs (1)
- Kohlendioxidabscheidung und -speicherung (CCS) (1)
- Korrosionsverhalten (1)
- Kriechen (1)
- Laser Powder Bed Fusion (1)
- Laser Powder Bed Fusion (LPBF) (1)
- Laser beam melting (LBM) (1)
- Laser irradiation (1)
- Laser powder bed fusion (1)
- Laser powder-based directed energy deposition (1)
- Laser-thermal shock (1)
- Life time prediction (1)
- Lifetime (1)
- Long-term aging (1)
- Low carbon steel (1)
- Low cycle fatigue (1)
- Low strain (1)
- Low-cycle fatigue (1)
- Magnetic domain distribution (1)
- Magnetic stray fields (1)
- Magneto-optical sensor (1)
- Magnetomechanical effect (1)
- Materials Testing (1)
- Materials informatics (1)
- Mechanical anisotropy (1)
- Mechanical properties (1)
- Mechanische Eigenschaften (1)
- Metal matrix composites (1)
- Microscopy (1)
- Microstructure evolution (1)
- Mikrostruktur (1)
- Miniature specimen (1)
- Misfitting precipitate (1)
- Molybdenum (1)
- Multiaxial deformation (1)
- Multi‐component diffusion (1)
- NDT (1)
- Neutron diffraction (1)
- Nickel-base alloy (1)
- Non-destructive Materials (1)
- Notch (1)
- Ontology (1)
- P91 (1)
- PBF-LB/M/316L (1)
- Parametric modeling (1)
- Phase‐field modeling (1)
- Precipitate shape (1)
- Precipitates (1)
- Process development (1)
- Quantitative Analyse (1)
- Radiation thermometry (1)
- Reference data (1)
- Reheating (1)
- Relaxation fatigue (1)
- Reproducibility (1)
- Reusable data (1)
- S-phase (1)
- SSiC (1)
- Safety (1)
- Selective laser melting (SLM) (1)
- Semantic Web Technologies (1)
- Shear modulus (1)
- Size effects (1)
- Solid solution softening (1)
- Solid solution strengthening (1)
- Standardisation (1)
- Strain difference (1)
- Stress distribution (1)
- Structural steel (1)
- Symmetric dwell periods (1)
- T1 precipitate (1)
- TIG weld (1)
- TMF (1)
- TNB-V5 (1)
- Temperature dependence (1)
- Temperature measurement (1)
- Tempered martensite ferritic steels (1)
- Tensile Test Ontology (1)
- Tensile properties (1)
- Thermal barrier coating (TBC) (1)
- Thermal shock (1)
- Thermal shock stress (1)
- Thermo-mechanical Fatigue (1)
- Thermography (1)
- Thermomechanical Fatigue (TMF) (1)
- Thermomechanical Fatigue (TMF); High Cycle Fatigue (HCF); Cast iron; Fatigue assessment (1)
- Thermomechanical fatigue (TMF) (1)
- Thermoschock (1)
- Thickening (1)
- Titanaluminide (1)
- Titanium alloys (1)
- Topography (1)
- Transmission electron microscopy (1)
- Transmission electron microscopy (TEM) (1)
- Visual ontology development (1)
- Vocabulary providers (1)
- Warmfeste Stähle (1)
- Weibull statistics (1)
- Young's modulus (1)
- Yttria stabilized zirconia (1)
- microstructural changes (1)
- γ″ phase (1)
- θ′ phase (1)
- θ′-(Al2Cu) precipitate phase (1)
Organisationseinheit der BAM
- 5 Werkstofftechnik (26)
- 5.2 Metallische Hochtemperaturwerkstoffe (26)
- 8 Zerstörungsfreie Prüfung (9)
- 9 Komponentensicherheit (8)
- 5.1 Mikrostruktur Design und Degradation (7)
- 5.5 Materialmodellierung (6)
- 8.5 Röntgenbildgebung (6)
- 9.6 Additive Fertigung metallischer Komponenten (4)
- 8.0 Abteilungsleitung und andere (3)
- 9.3 Schweißtechnische Fertigungsverfahren (3)
The amount of data generated worldwide is constantly increasing. These data come from a wide variety of sources and systems, are processed differently, have a multitude of formats, and are stored in an untraceable and unstructured manner, predominantly in natural language in data silos. This problem can be equally applied to the heterogeneous research data from materials science and engineering. In this domain, ways and solutions are increasingly being generated to smartly link material data together with their contextual information in a uniform and well-structured manner on platforms, thus making them discoverable, retrievable, and reusable for research and industry. Ontologies play a key role in this context. They enable the sustainable representation of expert knowledge and the semantically structured filling of databases with computer-processable data triples.
In this perspective article, we present the project initiative Materials-open-Laboratory (Mat-o-Lab) that aims to provide a collaborative environment for domain experts to digitize their research results and processes and make them fit for data-driven materials research and development. The overarching challenge is to generate connection points to further link data from other domains to harness the promised potential of big materials data and harvest new knowledge.
AbstractHigh-strength aluminum alloys used in aerospace and automotive applications obtain their strength through precipitation hardening. Achieving the desired mechanical properties requires precise control over the nanometer-sized precipitates. However, the microstructure of these alloys changes over time due to aging, leading to a deterioration in strength. Typically, the size, number, and distribution of precipitates for a quantitative assessment of microstructural changes are determined by manual analysis, which is subjective and time-consuming. In our work, we introduce a progressive and automatable approach that enables a more efficient, objective, and reproducible analysis of precipitates. The method involves several sequential steps using an image repository containing dark-field transmission electron microscopy (DF-TEM) images depicting various aging states of an aluminum alloy. During the process, precipitation contours are generated and quantitatively evaluated, and the results are comprehensibly transferred into semantic data structures. The use and deployment of Jupyter Notebooks, along with the beneficial implementation of Semantic Web technologies, significantly enhances the reproducibility and comparability of the findings. This work serves as an exemplar of FAIR image and research data management.
Fatigue tests were performed on the forged aluminum alloy EN AW-2618A in the T61 state. Different stress ratios (R = -1, R = 0.1) were selected to study the influence of mean stress on fatigue life. Two overaged states (10 h/230 ◦C, 1000 h/230 ◦C) were also tested to investigate the influence of overaging on fatigue life. Transmission electron microscopy (TEM) was used to characterize the precipitates (S-phase), which are mainly responsible for the strength of the alloy. A fractographic analysis was also performed to determine the failure mode. Overaging reduces the fatigue life compared to the T61 state. The longer the aging time, the lower the fatigue resistance. The reason is the decrease in (yield) strength, which correlates with the radius of the S-phase: the precipitate radius increases by a factor of approximately two for the overaged states compared to the initial state. The analysis of the fracture surfaces showed crack initiation occurs predominantly on the outer surface and is
associated with the primary phases.
The damage mechanisms of metallic components produced by process laser powder bed fusion differ significantly from those typically observed in conventionally manufactured variants of the same alloy. This is due to the unique microstructures of additively manufactured materials. Herein, the focus is on the study of the evolution of creep damage in stainless steel 316L specimens produced by laser powder bed fusion. X-ray computed tomography is used to unravel the influence of the process-specific microstructure from the influence of the initial void distribution on creep damage mechanisms. The void distribution of two specimens tested at 600 °C and 650 °C is analyzed before a creep test, after an interruption, and after fracture. The results indicate that the formation of damage is not connected to the initial void distribution. Instead, damage accumulation at grain boundaries resulting from intergranular cracking is observed.
Creep and creep damage behavior of stainless steel 316L manufactured by laser powder bed fusion
(2022)
This study presents a thorough characterization of the creep properties of austenitic stainless steel 316L produced by laser powder bed fusion (LPBF 316L) contributing to the sparse available data to date. Experimental results (mechanical tests, microscopy, X-ray computed tomography) concerning the creep deformation and damage mechanisms are presented and discussed. The tested LPBF material exhibits a low defect population, which allows for the isolation and improved understanding of the effect of other typical aspects of an LPBF microstructure on the creep behavior. As a benchmark to assess the material properties of the LPBF 316L, a conventionally manufactured variant of 316L was also tested. To characterize the creep properties, hot tensile tests and constant force creep tests at 600 °C and 650 °C are performed. The creep stress exponents of the LPBF material are smaller than that of the conventional variant. The primary and secondary creep stages and the times to rupture of the LPBF material are shorter than the hot rolled 316L. Overall the creep damage is more extensive in the LPBF material. The creep damage of the LPBF material is overall mainly intergranular. It is presumably caused and accelerated by both the appearance of precipitates at the grain boundaries and the unfavorable orientation of the grain boundaries. Neither the melt pool boundaries nor entrapped gas pores show a significant influence on the creep damage mechanism.
The underlying cause of mechanical anisotropy in additively manufactured (AM) parts is not yet fully understood and has been attributed to several different factors like microstructural defects, residual stresses, melt pool boundaries, crystallographic and morphological textures. To better understand the main contributing factor to the mechanical anisotropy of AM stainless steel 316L, bulk specimens were fabricated via laser powder bed fusion (LPBF). Tensile specimens were machined from these AM bulk materials for three different inclinations: 0◦, 45◦, and 90◦ relative to the build plate. Dynamic Young’s modulus measurements and tensile tests were used to determine the mechanical anisotropy. Some tensile specimens were also subjected to residual stress measurement via neutron diffraction, porosity determination with X-ray micro-computed tomography (μCT), and texture analysis with electron backscatter diffraction (EBSD). These investigations revealed that the specimens exhibited near full density and the detected defects were spherical. Furthermore, the residual stresses in the loading direction were between −74 ± 24 MPa and 137 ± 20 MPa, and the EBSD measurements showed a preferential ⟨110⟩ orientation parallel to the build direction. A crystal plasticity model was used to analyze the elastic anisotropy and the anisotropic yield behavior of the AM specimens, and it was able to capture and predict the experimental behavior accurately. Overall, it was shown that the mechanical anisotropy of the tested specimens was mainly influenced by the crystallographic texture.
This article reports temperature-dependent elastic properties (Young’s modulus, shear modulus) of three alloys measured by the dynamic resonance method. The alloys Ti-6Al-4V, Inconel IN718, and AISI 316 L were each investigated in a variant produced by an additive manufacturing processing route and by a conventional manufacturing processing route. The datasets include information on processing routes and parameters, heat treatments, grain size, specimen dimensions, and weight, as well as Young’s and shear modulus along with their measurement uncertainty. The process routes and methods are described in detail. The datasets were generated in an accredited testing lab, audited as BAM reference data, and are hosted in the open data repository Zenodo. Possible data usages include the verification of the correctness of the test setup via Young’s modulus comparison in low-cycle fatigue (LCF) or thermo-mechanical fatigue (TMF) testing campaigns, the design auf VHCF specimens and the use as input data for simulation purposes.
Evaluation of high spatial resolution imaging of magnetic stray fields for early damage detection
(2017)
The paper discusses the evaluation of elastic and plastic strain states in two low-carbon steels of the same steel group with high spatial resolution GMR (giant magneto resistance) sensors. The residual stress distributions of tungsten inert gas welded plates were determined by means of neutron diffraction as a reference. The normal component of local residual magnetic stray fields arise in the vicinity of the positions of maximum stress. The experiments performed on flat tensile specimen indicate that the boundaries of plastic deformations are a source of stray fields. The spatial variations of magnetic stray fields for both the weld and the tensile samples are in the order of the earths magnetic field.
Results of an extended TMF test program on grade P92 steel in the temperature range of 620 °C - 300 °C, comprising in-phase (IP) and out-of-phase (OP) tests, partly performed with symmetric dwells at Tmax/Tmin, are presented. In contrast to previous studies, the low-strain regime is also illuminated, which approaches flexible operation in a power plant with start/stop cycles. At all strain amplitudes, the material performance is characterized by continuous cyclic softening, which is retarded in tests at lower strains but reaches similar magnitudes in the course of testing. In the investigated temperature range, the phase angle does not affect fatigue life in continuous experiments, whereas the IP condition is more detrimental in tests with dwells. Fractographic analyses indicate creep-dominated and fatigue-dominated damage for IP and OP, respectively. Analyses of the (micro)hardness distribution in the tested specimens suggest an enhanced microstructural softening in tests with dwell times for the low- but not for the high-strain regime. To rationalize the obtained fatigue data, the fracture-mechanics-based D_TMF concept, which was developed for TMF life assessment of ductile alloys, was applied. It is found that the D_TMF parameter correlates well with the measured fatigue lives, suggesting that subcritical growth of cracks (with sizes from a few microns to a few millimeters) governs failure in the investigated range of strain amplitudes.
This article refers to the research article entitled “Creep-Fatigue of P92 in Service-Like Tests with Combined Stress- and Strain-Controlled Dwell Times” [1]. It presents experimental mechanical data from complex service-like creep-fatigue experiments performed isothermally at 620 °C and a low strain amplitude of 0.2 % on tempered martensite-ferritic grade P92 steel. The data sets in text file format provide cyclic deformation (min. and max. stresses) and the total (hysteresis) data of all recorded fatigue cycles for three different creep-fatigue experiments: 1) a standard relaxation fatigue (RF) test with symmetrical dwell times of three minutes introduced at minimum and maximum strain, 2) a fully strain-controlled service-like relaxation (SLR) test combining these three-minute peak strain dwells with a 30-minute dwell in between at zero strain, and 3) a partly stress-controlled service-like creep (SLC) test combining the three-minute peak strain dwells with 30-minute dwells at constant stress. Such service-like (SL) tests with additional long-term stress- and strain-controlled dwell times are non-standard, rare, and expensive, making these data very valuable. They may be used to approximate cyclic softening in the technically relevant range, for the design of complex SL experiments, or for detailed analyses of stress-strain hystereses (e.g., for stress or strain partitioning methods, for the determination of hysteresis energies (work), inelastic strain components, etc.). In addition, the latter analyses may supply important input for advanced parametric lifetime modeling of components under creep-fatigue loading or model calibration parameters.