Filtern
Erscheinungsjahr
Dokumenttyp
- Beitrag zu einem Tagungsband (38)
- Zeitschriftenartikel (34)
- Beitrag zu einem Sammelband (4)
- Vortrag (3)
- Posterpräsentation (2)
- Sonstiges (1)
Sprache
- Englisch (56)
- Deutsch (20)
- Mehrsprachig (6)
Schlagworte
- Rheology (30)
- Cement (10)
- Rheologie (10)
- Self-compacting concrete (9)
- Polycarboxylate ether (7)
- Concrete (6)
- Admixtures (5)
- Polycarboxylate (5)
- Polysaccharides (5)
- Fließmittel (4)
Organisationseinheit der BAM
- 7 Bauwerkssicherheit (10)
- 7.4 Baustofftechnologie (10)
- 7.2 Ingenieurbau (4)
Eingeladener Vortrag
- nein (3)
Superplasticizers (SPs) have been employed in concrete technology for decades to improve the workability of concrete in its fresh state. The addition of SPs in cement-based systems affects the early properties. Although the interaction of the cement particles with various SPs has been extensively researched, there still exists limited research on the interaction of SPs with supplementary cementitious materials such as rice husk ash (RHA). This paper investigates the rheological properties and early hydration kinetics of RHA-blended systems with three types of SPs, a polycarboxylate ether (PCE) and two lignosulphonates (LS-acc and LS-ret). In rheological properties, the addition of SP causes an initial improvement of workability as the yield stress is significantly reduced. The pastes with PCE and LS-acc show a slight increase of yield stress over time whereas pastes with LS-ret tend to lower the yield stress slightly over time, further improving the workability. Without SP, pastes with RHA show a lower yield stress but an increase in plastic viscosity as cement is further replaced with RHA. The addition of the LS SPs is observed to lower the plastic viscosity but remains constant with further replacement of cement with RHA. This indicates that LS SPs further adsorbs on RHA particles and hydration products produced causing dispersion of the particles
within the system. In early hydration kinetics, pastes with PCE retard hydration and the degree of retardation is further increased with LS SPs. In the presence of RHA, the retardation of LS SP systems is significantly reduced. The pastes with PCE show more ettringite in the SEM micrographs, but is observed to be shorter needles. This indicates an initial good workability for PCE. However, C-S-H and CH were observed to be low in quantity, whereby the pastes with LS show more nucleation sites for C-S-H and CH. The ettringite needles in the LS systems were similar in quantity and more elongated in some cases but not abundant as in the PCE systems.
Repair is an indispensable part of the maintenance of structures over their lifetimes. Structural grouting is a widely used remediation technique for concrete components, trenches, mine subsidence, dam joints, restoration of masonry structures, and geological stabilizations. A structural grout system should be injectable in narrow spaces and hence include ingredients with finer particles. Ultrafine cements are ideal for these type of demanding grouts due to their superior properties compared to that of the less expensive, but coarser ordinary Portland cement (OPC). Supplementary cementitious materials (SCMs) are often used to replace OPC clinker based binder in order to modify certain properties and to reduce costs. The most commonly used SCMs are fly ash (FA), and ground granulated blast furnace slag (GGBS). For various special applications microsilica (MS), and metakaolin (MK) are also used. Identifying the optimum replacement contents of OPC by SCMs are a challenge during the design of such grouts. The aim of this experimental study is to investigate the effect of the selected SCMs (FA, MS and MK) on the slump flow, time of efflux, viscosity, shrinkage, and compressive and flexural strength of ultrafine cement based grouts with constant water-binder ratio and superplasticizer content. The test program was formulated using Box-Behnken design principles. Maximum percentages of replacement with ultrafine cement was 6% by volume of cement for MS and 16% for FA, and MK. The results suggest that most investigated grouts have the potential to be used for structural applications. The appropriate quadratic models are then formulated through statistical tools and presented as response surfaces. The trends indicate that fly ash improves the rheological properties, whereas microsilica and metakaolin positively affect shrinkage and mechanical properties to some extent. Based on the influence of SCMs and priorities among the properties, Decision Matrix Analysis (DMA) is carried out to select the most suitable ones among the SCMs. The analysis suggests that microsilica and fly ash are more suitable as SCMs than metakaolin without affecting the properties.
Superplasticizer and Shrinkage Reducing Admixture Dosages for Microfine Cement in Grout Systems
(2019)
Grouts have numerous applications including crack repair as maintenance in construction industries. Microfine cements are intensively used for high strength mortar and grout products. They are ideal for injection grouting in structural repair. Such grouts should have suitable rheological properties to be injectable, especially those used in repair and rehabilitation. The use of superplasticizers (SP) in these products is thus becoming increasingly crucial to achieve favorable workability and viscosity properties. A difficulty in such grouts is the plastic shrinkage due to finer particles used. It is thus necessary to determine optimum SP and shrinkage reducing admixture (SRA) dosages for a microfine cement based grout. In this study, a saturation dosage was decided from two Polycarboxylate ether (PCE) based SPs in relation to neat cement using slump flow and rheological parameters. A range of grout mixtures was formulated containing micro silica (MS) and fly ash (FA), and tested for suitable rheological and mechanical parameters. Based on the results, a grout mixture with MS and FA was selected to determine optimum SRA content. According to the results, a SP dosage of 3% by weight of neat cement is sufficient to achieve saturation. The grout material including MS and FA can produce comparable properties to neat cement grout. MS is found to improve compressive strength within the range considered, whereas a higher FA content provides favourable rheological properties. Finally, a SRA dosage of 4%, which could reduce the shrinkage by about 43% after 28d days, is determined for the grout system.
Globally, cement and concrete experts are at the cutting-edge to sustainable, green, healthy but nonetheless high-performance concrete. Today concrete is not yet well established in Africa, which offers the unique opportunity to build up a cement and concrete market based on the highest available state of technology. As this industry needs high level expertise, a central issue in implementation of skilled technology is crosslinking research institutions and laboratories. It should not be neglected that concrete is a product with low transport ranges. This means that an improved concrete market mainly supports the local economy without exceeding financial drains to the international market. Thus it fosters the fight against poverty, which is an urgent need in most African countries. The project aims to cross-link experts with industry and policy making bodies, aiming to establish sustainable cement and concrete construction in Africa.
Im Hinblick auf die Konformitätsbewertung der Druckfestigkeit von Beton wird es in der für 2014 geplanten Fassung der EN 206 signifikante Änderungen geben. Neben den bisher bekannten Verfahren werden auch sogenannte Kontrollkartensysteme als Konformitätsnachweis zugelassen. Dabei können beliebige Kontrollkartensysteme verwendet werden, sofern nachgewiesen werden kann, dass der maximale Durchschlupf (Average Outgoing Quality Limit, AOQL) 5 % beträgt. Im informativen Normenanhang werden zwei grundlegende Verfahren, das sogenannte Shewhart-Verfahren sowie das CUSUM-Verfahren (Cumulative Sum) beschrieben, welche beide die Forderung an das AOQL erfüllen.
Kontrollkartensysteme sind eigentlich Werkzeuge zur Prozesssteuerung. Sie können effektiv dabei helfen, die Produktion technisch, ökonomisch und ökologisch zu optimieren. Allerdings sind Kontrollkarten deutlich komplexer in der Anwendung als die bisher normativ erfassten Methoden. Der vorliegende Beitrag stellt die neuen Verfahren und deren Besonderheiten anhand von Beispielen vor. Darüber hinaus werden der Zusatznutzen bei sachgerechter Anwendung im Vergleich und Vor- und Nachteile zu den bisherigen Verfahren dargestellt und diskutiert.--------------------------------------------------------------------------------------
With regard to the conformity assessment of the compressive strength of concrete, there will be significant changes in the EN 206, which is scheduled for publication in 2014. So called control chart systems will be approved supplementary to the existing methods. Any control chart can be used as long as the system can grant an average outgoing quality limit (AOQL) of 5 %. The informative appendix of the standard presents two fundamental control chart methods, the so called Shewhart method and the CUSUM method (cumulative sum), both of which fulfill the required AOQL.
Control card systems are actually tools for process control. They can effectively help to optimise production processes technically, economically, and ecologically. However, control charts are much more complex to use than the methods known from the recently applied standard. This paper presents these new methods and their characteristics using examples. Furthermore, the additional benefit of these systems is illustrated and advantages and disadvantages are discussed in comparison to existing methods.
Innovative admixture technology has significantly widened up the ränge of possibilities of concrete engineers. For many decades the water to cement ratio (w/c) was the major influencing factor for the performance of concrete. Due to the need to adjust a consistency, which still allowed reasonable workability, the w/c was typically significantly higher than technologically reasonable. Rheology modifying admixtures Support adjusting the concrete consistency largely independent of the w/c. It was only after the invention of the first superplasticizers that modern concrete technology significantly evolved in terms of flowability, strength, and durability, and only due to the steady evolution of the technology modern innovations, such as Self-Compacting Concrete, Ultra-High-Performance Concrete, or Engineered Cementitious Composites were made possible. Today’s superplasticizers are extremely versatile and can be adjusted to individual technological specifications. However, the other side of the coin of versatility is that cementitious Systems incorporating superplasticizers have become more sensitive against environmental influences, such as the environmental temperature, which may cause unwanted effects or demand for supplementary admixture use such as stabilizing admixtures. Hence, concrete mixture composition with admixtures demands for a high level of expertise and offen there is lack of awareness about the mode of Operation of rheology modifying admixtures among concrete technologists. The paper gives a comprehensive overview about rheology modifying admixtures such as superplasticizers or stabilizing agents, and how they can be used depending upon the application in the most favourable way. Based on experiences with the sub-Saharan African concreting boundary conditions, which exhibit many challenges in terms of environmental boundary conditions and construction site logistics, conclusions are finally drawn, how admixtures can be used in the most beneficial way to improve the concrete casting Situation.
Innovative admixture technology has significantly widened up the ränge of possibilities of concrete engineers. For many decades the water to cement ratio (w/c) was the major influencing factor for the performance of concrete. Due to the need to adjust a consistency, which still allowed reasonable workability, the w/c was typically significantly higher than technologically reasonable. Rheology modifying admixtures Support adjusting the concrete consistency largely independent of the w/c. It was only after the invention of the first superplasticizers that modern concrete technology significantly evolved in terms of flowability, strength, and durability, and only due to the steady evolution of the technology modern innovations, such as Self-Compacting Concrete, Ultra-High-Performance Concrete, or Engineered Cementitious Composites were made possible. Today’s superplasticizers are extremely versatile and can be adjusted to individual technologicalspecifications. However, the other side of the coin of versatility is that cementitious Systems incorporating superplasticizers have become more sensitive against environmental influences, such as the environmental temperature, which may cause unwanted effects or demand for supplementary admixture use such as stabilizing admixtures. Hence, concrete mixture composition with admixtures demands for a high level of expertise and offen there is lack of awareness about the mode of Operation of rheology modifying admixtures among concrete technologists. The paper gives a comprehensive overview about rheology modifying admixtures such as superplasticizers or stabilizing agents, and how they can be used depending upon the application in the most favourable way. Based on experiences with the sub-Saharan African concreting boundary conditions, which exhibit many challenges in terms of environmental boundary conditions and construction site logistics, conclusions are finally drawn, how admixtures can be used in the most beneficial way to improve the concrete casting Situation.
Rheological optimisation for flowable mixture compositions specified for African boundary conditions
(2013)
To date concrete technology is not yet well established in sub-Saharan Africa but considering the construction technological challenges of the region, without doubt, concrete will play a major role in future. The social, economic, and geographic boundary conditions distinguish greatly from those that can be found in many other regions of the world, where concrete is considerably well established. Düring the last decades, concrete technology underwent a rapid evolution process, but in most countries, where concrete is already well established, innovations are difficult to be brought into practice, Africa, currently has the opportunity and potential, of directly establishing the best available practice in concrete technology.
The conclusion is drawn that self-compacting concrete (SCC) or highly flowable concrete is a reasonable solution for African construction sites. Since on most African construction sites the disadvantageous concreting environment is the most crucial factor for the concrete quality, the outstanding workability properties outweigh any disadvantages of SCC.
Based on this consideration, concepts are developed, how to bring about robust SCC cost-efficiently and reliably into practice as pre-mixed dry compound under consideration of local materials such as rice husk ashes, bagasse ashes, natural pozzolans, cassava starch and lignosulphonate.
The cement and concrete market in East, Central and Southern Africa is highly fragmented. The concrete industry in this area consists of multiple parties, including producers and suppliers of construction materials, formal and informal contractors, engineers and architects, unions of trades persons and workmen, governmental bodies and formal institutions of research and education. All these institutions mostly do not interact adequately, which makes building with cementitious materials susceptible to damage and failures. Completely opposed to the situation in Europe or North America, cement in Africa is often unaffordable, while manpower is cheap, which results in a questionable economisation of cement. Typically, there is not sufficient awareness of methods to sensibly reducing the cement content in concrete or replace Ordinary Portland Cement by adequate alternative materials. Research activities in this field of technology are often missing completely. Only few countries in the area, such as South Africa, are exempted from these issues.
This paper presents the SPIN project, which is a joint project of a consortium of 8 African and 3 European partners within the ACP Science and Technology Programme. The project is funded by the EC and ACP Secretariat is the project body. The main objective of the current project is to strengthen the cement and concrete industry in the East and Central African regions. The project shall generate reasonable solution strategies to implement clean, safe and sustainable cement and concrete technology on the African continent, including general and specific guidelines for sensible application. Furthermore it shall be the kick-off for future projects, research activities and the world-wide expansion of a European-African network.
The paper addresses special problems the cement and concrete market in Eastern, Central and Southern African countries has to face. Several options are presented in detail, which shall help overcoming the current situation. Customized solutions for the African market include rational methods for reducing the amount of cement used and the replacement of Ordinary Portland Cement with cheaper alternatives. The use of recycled concrete through a new and economically effective method, as well as the opportunity of using locally available resources is also discussed.
While today, engineers can choose from a wide range of rheology modifying admixtures, in some parts of the world, these are difficult to access, due to their complex processing. However, alternatives can be bio‐based polymers such as polysaccharides from various sources. These are easily accessible all over the world, do not demand for complicated processing, and typically they are more sustainable than many established materials, which are crude oil‐based.
The paper presents the effects of acacia gum, cassava starch and the gum of triumfetta pendrata A. Rich on the rheological performance of cementitious systems. It is shown that acacia gum can be as efficient as polycarboxylate based superplasticisers, cassava starch can reduce the yield stress slightly with little effect on the plastic viscosity, and the gum of triumfet ta pendrata A. Rich increases the thixotropy of cement pastes with plasticizing polymers significantly.
Während für die Bauwirtschaft in den meisten Ländern der nördlichen Halbkugel die Instandhaltung bestehender Strukturen und Infrastruktur im Vordergrund steht, geht es in vielen Ländern der Südhalbkugel in der Hauptsache um die Schaffung von Bauwerken und Infrastruktur zur Verwirklichung angemessener Lebensbedingungen, was wiederum das schnelle Wirtschaftswachstum weiter befeuert.
Beton ist als Massenbaustoff, trotz landläufig anderer Bewertung, aufgrund seines im Vergleich zu anderen Baustoffen günstigen CO2-Footprints und der globalen Verfügbarkeit hierbei aktuell ohne Alternative. Allerdings ist Beton nach Wasser das am zweithäufigsten genutzte Produkt auf Erden [1] und die globale Nachfrage und Produktion steigt dramatisch. Dies hat Konsequenzen für das globale Klima, denn gerade die als Bindemittel eingesetzten Portlandzemente verursachen bei ihrer Herstellung selbst unter modernsten Produktionsbedingungen große Mengen an CO2.
Deshalb müssen für zukünftige nachhaltigere Technologien neuartige Betone entwickelt werden, die bei gleicher oder verbesserter Leistungsfähigkeit, einen geringeren Bedarf an Portlandzement aufweisen.
Um den CO2-Ausstoß, der mit der Betonherstellung verbunden ist zu minimieren, müssen Anteile an Portlandzement im Bindemittel reduziert und durch nachhaltigere Ersatzstoffe ausgetauscht werden. Darüber hinaus muss das eingesetzte Bindemittel im Beton so effizient wie möglich ausgenutzt werden. Das heißt, ein Bauteil oder Bauwerk sollte gerade so viel Bindemittel enthalten, wie für die Tragfähigkeit und Dauerhaftigkeit erforderlich ist. Hierfür erscheint der Einsatz von leistungsfähigen bauchemischen Produkten unumgänglich. Diese können zum einen die veränderten Verarbeitungseigenschaften, die Zementersatzstoffe mit sich bringen, ausgleichen und gleichzeitig helfen, den Gesamtwassergehalt zu minimieren, so dass das Bindemittel seine maximale Leistungsfähigkeit erzielt. Fließmittel sind aktuell die wichtigsten Zusatzmittel für Beton. Sie reduzieren den Wasserbedarf und ermöglichen, Zement im Beton effizienter auszunutzen. Darüber hinaus sind Stabilisierer wichtig zur Erhöhung der Robustheit, insbesondere im Hinblick auf die bautechnischen Herausforderungen der Zukunft – vom Pumpen über weite Distanzen, dem Spritzen, dem Betonieren bei extremen Klimabedingungen bis hin zum 3D-Druck.
Rice husk as (RHA) is an eco-friendly material, which can be used as a supplementary cementitious material (SCM) in cement and concrete. Due to the high water demand for the material, superplasticizers (SPs) are essential to improve the performance. However, the interaction between the SPs and RHA systems is limited. This paper investigates the interaction of the binders with three SPs, i.e. two polycarboxylate ethers (PCEs) and one lignosulphonate (LS). The investigations are performed on blended systems of mortar containing various percentages of RHA and limestone powder (LSP). LSP is used in this research to improve the workability of the mortar. The results from the zeta potential (ZP) shows that the SPs are extremely dependent on the pH of the suspension. At higher pH values such as in a cementitious system, the ZP becomes less negative indicating that the ions in the suspension interact with the carboxyl groups in the backbone of the polymers thus reducing the surface charges of the SP. The mini-slump flow shows that the workability of the blended mortar systems is significantly improved with the addition of SPs. LS systems with increasing RHA is observed to have similar workability as the control mix over time. The compressive strength test results show increased strength for all mortar specimens with added RHA and LSP at later ages.
Rising temperatures worldwide pose an increasing challenge for safe and healthy living conditions. Particularly inner cities have been affected by these environmental changes because of the materials used to build houses, streets and infrastructure. The most common building material is concrete. It shows a specific heat capacity, while the heat conductivity for Standard concrete is low. Thus, the use of concrete generates a high capacity of heat storage. In addition, extensive soil sealing also contributes to the temperature rise of inner city areas compared to
their surroundings. To mitigate this so-called urban heat island effect, a self-cooling concrete paver was developed. This paver is able to store water. The evaporation of the water at elevated temperatures provides a cooling effect. This paper focuses on determination of this new paver’s capability to cool the surface and the surrounding. The new paver’s cooling Qualities were analysed in a series of laboratory tests. To prove the results outside of laboratory conditions, two fields (12 m × 8 m) with self-cooling and reference pavers were installed in Spain.
This paper presents and discusses the results of the tests. Correlation between reduced surface temperature of the self-cooling concrete pavers and the air temperature is examined.
There is a wide range of research worldwide on supplementary cementitious materials (SCMs) such as fly ash and slag for substituting pure cement. Such materials are suitable to be considered in a cementitious system with ordinary Portland cement (OPC) due to their high pozzolanic properties. In addition, majority of the SCMs are said to significantly improve concrete properties especially in terms of increased strength and durability. Unfortunately, the production of such SCMs is not entirely eco-friendly and also limited to certain parts of the world, hence one has to look at alternative options.
The issue of availability of resources is a strong concept that is ever-increasing, and the use of more eco-friendly SCMs in a cementitious system is furthermore attractive. Hence this paper addresses the use of eco-friendly SCMs in concrete such as rice husk ash (RHA). Despite the fact that extensive research has been done on this material, its application in a cementitious system to obtain sufficient concrete properties is still rather limited. In a country like Tanzania, high strength concrete construction is applicable in special construction cases but certainly not a high priority. Majority of construction is still undertaken using normal strength concrete. In a ternary cementitious system consisting of OPC, RHA and other readily available resources such as limestone filler (LSF), normal strength concrete can still be produced having good performance and suitable for regular on-site construction. This paper explains a possible application of obtaining sufficient concrete properties from the available resources.