Filtern
Dokumenttyp
- Zeitschriftenartikel (12) (entfernen)
Schlagworte
- Automated manufacturing (2)
- Fatigue tests (2)
- Mechanical properties (2)
- Notch stress approach (2)
- Tubular X-joints (2)
- Wire arc additive manufacturing (2)
- Adaptive control (1)
- Additive manufacturing (1)
- AlMg0.7SiTiB filler wire (1)
- Automatisierte Fertigung (1)
- Carbon dioxide footprint (1)
- Digitalisierung (1)
- Digitalization (1)
- Digitization (1)
- Environmental impact categories (1)
- Equivalent stress concentration factors (1)
- GMA welding (1)
- Gleeble testing (1)
- Grade S960QL steel (1)
- Grain refinement (1)
- HSLA (1)
- Hardly separable problem (1)
- Hohlprofilknoten (1)
- Kerbspannungskonzept (1)
- Laser beam welding (1)
- Life cycle assessment (1)
- Local fatigue spproaches (1)
- Material modeling (1)
- Model calibration (1)
- Model order reduction (1)
- Narrow gap welding (1)
- Neural networks (1)
- Numerical welding simulation (1)
- Open science (1)
- Open source (1)
- Precipitation hardening aluminum alloys (1)
- Proper generalized decomposition (1)
- Research data management (1)
- Residual stress (1)
- Resistance spot welding (1)
- Schweißnahtgeometrie (1)
- Sensor (1)
- Strain-rate (1)
- Stress-strain behavior (1)
- Structural stress approach (1)
- Technical crack detection (1)
- Transformable steels (1)
- Tubular joints (1)
- Umweltschutz (1)
- Viscoplasticity (1)
- Weld seam geometry (1)
- Welding (1)
- Weldx (1)
- digital image correlation (1)
- dual phase steel (1)
- resistance spot welding (1)
- Äquivalente Spannungskonzentrationsfaktoren (1)
Organisationseinheit der BAM
- 9.3 Schweißtechnische Fertigungsverfahren (12) (entfernen)
The sound numerical prediction of welding-induced thermal stresses, residual stresses, and distortions strongly depends on the accurate description of a welded material’s thermomechanical deformation behaviour. In this work, we provide experimental data on the viscoplastic deformation behaviour of a grade-s960ql steel up to a temperature of 1000 ◦C. In addition, a multi-phase viscoplastic material model is proposed, which accounts for the experimentally observed isothermal deformation behaviour of grade-s960ql steel base and austenitised material, as well as for athermal contributions that originate from solid-state phase transformations. The multi-phase viscoplastic and a classic rateindependent isotropic hardening material model were applied in the numerical simulations of both-ends-fixed bar Satoh tests and a single-pass gas metal arc weld. The influence of material modelling choices on the agreement between numerical simulation and experimental results is discussed, and recommendations for further work are given.
In order to generate a material data base for computational welding mechanics, temperature and strain-rate dependent stress-strain experiments were performed by using a Gleeble®3500 testing system. The object of the investigation was HSLA transformable steel S960QL and related solid phases as bainite, martensite and austenite. For the production of these solid phases, the base material was heat treated according to an average weld temperature cycle which was extracted within the heat affected zone of a thermal numerical weld simulation of a GMA weld. The hot tensile tests were carried out via cost-saving flat specimen geometries. Two experimental series with different strain-rates were conducted, where the longitudinal strain-rate was controlled by specification of the transversal strain-rate applying Poisson’s-ratio. Subsequently, the resulting stress-strain curves were approximated in accordance with the Ramberg-Osgood-materials law. Consequently, it is shown that the temperature and strain-rate dependent stress-strain behavior of metals can be successfully characterized by means of a Gleeble®-system.
However, this requires a control of the longitudinal strain-rate by specification of the transversal strain-rate. The related experimental procedure and the method of evaluation are explained in detail. With regard to all tested solid phases, a significant strain-rate dependency can only be observed upwards from temperatures of 400 °C. Based on experimental results, Ramberg-Osgood-parameters will be presented to describe the stress-strain behavior of steel S960QL and related solid phases for temperatures between 25 °C and 1200 °C. Furthermore, the use of costsaving flat specimen-geometry appears reasonable.