Filtern
Erscheinungsjahr
Dokumenttyp
Sprache
- Englisch (24)
- Mehrsprachig (1)
Schlagworte
Organisationseinheit der BAM
Air pollution within industrial scenarios is a major risk for workers, which is why detailed knowledge about the dispersion of dusts and gases is necessary. This paper introduces a system combining stationary low-cost and high-quality sensors, carried by ground robots and unmanned aerial vehicles. Based on these dense sampling capabilities, detailed distribution maps of dusts and gases will be created. This system enables various research opportunities, especially on the fields of distribution mapping and sensor planning. Standard approaches for distribution mapping can be enhanced with knowledge about the environment’s characteristics, while the effectiveness of new approaches, utilizing neural networks, can be further investigated. The influence of different sensor network setups on the predictive quality of distribution algorithms will be researched and metrics for the quantification of a sensor network’s quality will be investigated.
The Sharp GP2Y1010AU0F is a widely used low-cost dust sensor, but despite its popularity, the manufacturer provides little information on the sensor. We installed 16 sensing nodes with Sharp dust sensors in a hot rolling mill of a steel factory. Our analysis shows a clear correlation between sensor drift and accumulated production of the steel factory. An eye should be kept on the long-term drift of the sensors to prevent early saturation. Two of 16 sensors experienced full saturation, each after around eight and ten months of operation.
Wireless sensor networks provide occupational health experts with valuable information about the distribution of air pollutants in an environment. However, especially low-cost sensors may produce faulty measurements or fail completely. Consequently, not only spatial coverage but also redundancy should be a design criterion for the deployment of a sensor network. For a sensor network deployed in a steel factory, we analyze the correlations between sensors and build machine learning forecasting models, to investigate how well the sensor network can compensate for the outage of sensors. While our results show promising prediction quality of the models, they also indicate the presence of spatially very limited events. We, therefore, conclude that initial measurements with, e.g., mobile units, could help to identify important locations to design redundant sensor networks.
This presentation gives an introduction to the gas-sensitive aerial robots developed at BAM, including various application examples in the field of mobile robot olfaction: gas source localization and gas distribution mapping.
Gas distribution mapping is important to have an accurate understanding of gas concentration levels in hazardous environments. A major problem is that in-situ gas sensors are only able to measure concentrations at their specific location. The gas distribution in-between the sampling locations must therefore be modeled. In this research, we interpret the task of spatial interpolation between sparsely distributed sensors as a task of enhancing an image's resolution, namely super-resolution. Because autoencoders are proven to perform well for this super-resolution task, we trained a convolutional encoder-decoder neural network to map the gas distribution over a spatially sparse sensor network. Due to the difficulty to collect real-world gas distribution data and missing ground truth, we used synthetic data generated with a gas distribution simulator for training and evaluation of the model. Our results show that the neural network was able to learn the behavior of gas plumes and outperforms simpler interpolation techniques.
Occupational health is an important topic, especially in industry, where workers are exposed to airborne by-products (e.g., dust particles and gases). Therefore, continuous monitoring of the air quality in industrial environments is crucial to meet safety standards. For practical and economic reasons, high-quality, costly measurements are currently only carried out sparsely, both in time and space, i.e., measurement data are collected in single day campaigns at selected locations only.
Recent developments in sensor technology enable cost-efficient gas monitoring in real-time for long-term intervals. This knowledge of contaminant distribution inside the industrial environment would provide means for better and more economic control of air impurities, e.g., the possibility to regulate the workspace’s ventilation exhaust locations, can reduce the concentration of airborne contaminants by 50%.
This paper describes a concept proposed in the project “Robot-assisted Environmental Monitoring for Air Quality Assessment in Industrial Scenarios“ (RASEM). RASEM aims to bring together the benefits of both – low- and high-cost – measuring technologies: A stationary network of low-cost sensors shall be augmented by mobile units carrying high-quality sensors. Additionally, RASEM will develop procedures and algorithms to map the distribution of gases and particles in industrial environments.
To better understand the dynamics in hazardous environments, gas distribution mapping aims to map the gas concentration levels of a specified area precisely. Sampling is typically carried out in a spatially sparse manner, either with a mobile robot or a sensor network and concentration values between known data points have to be interpolated. In this paper, we investigate sequential deep learning models that are able to map the gas distribution based on a multiple time step input from a sensor network. We propose a novel hybrid convolutional LSTM - transpose convolutional structure that we train with synthetic gas distribution data. Our results show that learning the spatial and temporal correlation of gas plume patterns outperforms a non-sequential neural network model.
In this paper, we show that a micro unmanned aerial vehicle (UAV) equipped with commercially available gas sensors can address environmental monitoring and gas source localization (GSL) tasks. To account for the challenges of gas sensing under real-world conditions, we present a probabilistic approach for GSL that is based on a particle filter (PF). Simulation and real-world experiments demonstrate the suitability of this algorithm for micro UAV platforms.
In this paper, we show that a micro unmanned aerial vehicle (UAV) equipped with commercially available gas sensors can address environmental monitoring and gas source localization (GSL) tasks. To account for the challenges of gas sensing under real-world conditions, we present a probabilistic approach to GSL that is based on a particle filter (PF). Simulation and real-world experiments demonstrate the suitability of this algorithm for micro UAV platforms.
This paper introduces a novel robotic platform for aerial remote gas sensing. Spectroscopic measurement methods for remote sensing of selected gases lend themselves for use on mini-copters, which offer a number of advantages for inspection and surveillance. No direct contact with the target gas is needed and thus the influence of the aerial platform on the measured gas plume can be kept to a minimum. This allows to overcome one of the major issues with gas-sensitive mini-copters. On the other hand, remote gas sensors, most prominently Tunable Diode Laser Absorption Spectroscopy (TDLAS) sensors have been too bulky given the payload and energy restrictions of mini-copters. Here, we introduce and present the Unmanned Aerial Vehicle for Remote Gas Sensing (UAV-REGAS), which combines a novel lightweight TDLAS sensor with a 3-axis aerial stabilization gimbal for aiming on a versatile hexacopter. The proposed system can be deployed in scenarios that cannot be addressed by currently available robots and thus constitutes a significant step forward for the field of Mobile Robot Olfaction (MRO). It enables tomographic reconstruction of gas plumes and a localization of gas sources. We also present first results showing the gas sensing and aiming capabilities under realistic conditions.