Filtern
Dokumenttyp
- Vortrag (18)
- Beitrag zu einem Tagungsband (5)
- Zeitschriftenartikel (4)
- Sonstiges (1)
- Posterpräsentation (1)
- Forschungsbericht (1)
Schlagworte
- Behälterversagen (14)
- Alternative Antriebe (9)
- Fahrzeugbrand (8)
- LPG (8)
- BOS (6)
- Security (5)
- Auswirkungsbetrachtung (4)
- Blast (4)
- Großversuch (4)
- Messtechnik (4)
Organisationseinheit der BAM
- 2.1 Sicherheit von Energieträgern (30) (entfernen)
Innovative Lösungen im Bereich der zivilen Sicherheitstechnologie müssen sehr genau auf die Ansprüche der Endanwender*innen abgestimmt werden. Das vom Bundesministerium für Bildung und Forschung (BMBF) geförderte Innovationsforum InnoBOSK der Bundesanstalt für Materialforschung und -prüfung (BAM) ermöglicht erstmalig die Vernetzung von Behörden und Organisationen mit Sicherheitsaufgaben (BOS) mit kleinen und mittleren Unternehmen (KMU). Während verschiedener Workshops, einer zweitägigen Konferenz und auf der digitalen Plattform des Projekts können Anbieter*innen und Endanwender*innen technischer Ausstattung in der zivilen Gefahrenabwehr in Kontakt treten.
In case of a vehicle fire, an installed LPG (liquefied petroleum gas) tank with a malfunctioning safety device poses severe hazards. To investigate the consequences in case of tank failure, we conducted 16 tests with toroidal shaped LPG vehicle tanks. Three tanks were used for a Hydraulic Burst Test under standard conditions. Another three tanks were equipped with a statutory safety device and were subjected to a gasoline pool fire. The safety device prevented tank failure, as intended. To generate a statistically valid dataset on tank failure, ten tanks without safety devices were exposed to a gasoline pool fire. Five tanks were filled to a level of 20 %; the re-maining five were filled to a level of 100 %. In order to gain information on the heating process, three tem-perature readings at the tank surface, and three nearby flame temperatures were recorded. At distances of l = (7; 9; 11) m to the tank, the overpressure of the shock wave induced by the tank failure and the unsteady tem-peratures were measured. All ten tanks failed within a time of t < 5 min in a BLEVE (boiling liquid expanding vapor explosion). Seven of these resulted directly in a catastrophic failure. The other three resulted in partial failure followed by catastrophic failure. A near field overpressure at a distance of l = 7 m of up to p = 0.27 bar was measured. All ten tests showed massive fragmentation of the tank mantle. In total, 50 fragments were found. These 50 fragments make-up 88.6 % of the original tank mass. Each fragment was georeferenced and weighed. Fragment throwing distances of l > 250 m occurred. For the tanks with a fill level of 20 %, the average number of fragments was twice as high as it was for the tanks that were filled completely.
Compressed natural gas (CNG) is a widely used automotive fuel in a variety of countries. In case of a vehicle fire where the safety device also malfunctions, a failure of the CNG automotive cylinder could occur. Such a cylinder failure is associated with severe hazards for the surrounding environment. Firstly, a comprehensive analysis is given below, summarizing various accidents involving CNG automotive cylinders and their consequences. In an extensive experimental program, 21 CNG automotive cylinders with no safety device were tested. Of the 21, burst tests were carried out on 5 Type III and 5 Type IV cylinders. Furthermore, fire tests with 8 Type III and 3 Type IV cylinders were conducted. Apart from cylinder pressure, inner temperature and cylinder mantle temperature, the periphery consequences, such as nearfield blast pressure and fragmentation are documented. The maximum measured overpressure due to a Type III cylinder failure was p = 0.41 bar. Each traceable fragment was georeferenced. All-in-all, fragment throw distances of d > 300 m could be observed. As one key result, it can be stated that the tested Type IV CNG cylinders showed less critical failure behavior then the Type III cylinders under fire impingement.
Es wurden insgesamt 57 Einzelversuche zum Versagen von Druckgasbehältern durchgeführt. Untersucht wurden dabei 11-kg-Propangasflaschen, PKW-Radmuldentanks für LPG sowie CNG-Tanks vom Typ III (Compositetanks mit Aluminiumliner) und Typ IV (Compositetanks mit Polymerliner). Mit 18 hydraulischen Berstversuchen wurde das Versagensverhalten unter kalten Bedingungen charakterisiert. In 39 Unterfeuerungsversuchen mit den gefüllten LPG- und CNG-Tanks, davon 36 mit Tanks ohne Sicherheitseinrichtung, wurde das Behälterversagen durch Brandbeaufschlagung untersucht. Neben verschiedenen Behältermanteltemperaturen und dem Behälterinnendruck wurde auch die Temperatur des gespeicherten Mediums dokumentiert. Dadurch war es möglich, genau zu dokumen-tieren, unter welchen Bedingungen und bei welchem Zustand der Behälter versagt hat. In einem Großteil der Unterfeuerungsversuche mit Behältern ohne Sicherheitseinrichtungen kam es zur Bildung eines Feuerballs, einer massiven Druck- und Temperaturwirkung auf den Nahbereich sowie einer Vielzahl von Fragmenten im Nah- und Fernbereich. In einer Entfernung von l = 7 m wurden Überdrücke von bis zu p = 0,41 bar gemessen. In 30 Unterfeuerungsversuchen kam es zur Fragmentierung des Behälters. Dabei konnten 159 Fragmente mit Wurfweite und Masse dokumentiert werden. Die dabei maximal festgestellte Wurfweite eines Fragments lag bei
l = 311 m.
Es wurden insgesamt 57 Einzelversuche zum Versagen von Druckgasbehältern durchgeführt. Untersucht wurden dabei 11-kg-Propangasflaschen, PKW-Radmuldentanks für LPG- sowie CNG-Tanks vom Typ III (Compositetanks mit Aluminiumliner) und Typ IV (Compositetanks mit Polymerliner). Mit 18 hydraulischen Berstversuchen wurde das Versagensverhalten unter kalten Bedingungen charakterisiert. In 39 Unterfeuerungsversuchen mit den gefüllten LPG- und CNG-Tanks, davon 36 mit Tanks ohne Sicherheitseinrichtung, wurde das Behälter¬ver¬sagen durch Brandbeaufschlagung untersucht. Neben verschiedenen Behältermantel¬temperaturen und dem Behälterinnendruck wurde auch die Temperatur des gespeicherten Mediums dokumentiert. Dadurch war es möglich, genau zu dokumentieren, unter welchen Bedingungen und bei welchem Zustand der Behälter versagt hat. In einem Großteil der Unterfeuerungsversuche mit Behältern ohne Sicherheitseinrichtungen kam es zur Bildung eines Feuerballs, einer massiven Druck- und Temperaturwirkung auf den Nahbereich sowie einer Vielzahl von Fragmenten im Nah- und Fernbereich. In einer Entfernung von l = 7 m wurden Überdrücke von bis zu p = 0,41 bar gemessen. In 30 Unterfeuerungsversuchen kam es zur Fragmentierung des Behälters. Dabei konnten 159 Fragmente mit Wurfweite und Masse dokumentiert werden. Die dabei maximal festgestellte Wurfweite eines Fragments lag bei l = 311 m.
In the field of explosive reactions, there is a type of explosive effect that lacks a sufficient database and reproducible experiments regarding biomechanics. It concerns the primary explosive effect. It is defined as pure shock wave of the explosion. The physical behavior of the shock wave when interacting with different types of tissue and, in particular, the subsequent transitions of the shock wave, have barely been investigated. The transition of the shock wave into other materials is the focus of the research Therefore, the aim of the investigations is the development of a multidisciplinary method to investigate shock wave behavior in various generic tissue simulants under the most reproducible conditions possible with realistic loads in an experimental test series with short set-up times. An autoclave is used to generate the pressure waves. A simplified torso model consisting of ballistic gelatin is used as a simulant.
In this paper, the influence of protective equipment on the pressure load in the tissue simulant is investigated. For this purpose, consecutive test setups are used. First, the behavior of ballistic gelatin as a tissue simulant is investigated. Then, the simplified torso model is covered with typical combat clothing consisting of four layers.
Afterwards a currently used UHMWPE ballistic protective plate is placed in front of the simplified torso model.
Finally, the combat clothing and the protective plate are examined in combination. Three cast-in pressure sensors are used as measuring devices, as well as an acceleration sensor attached to the protective plate.
The experiments show that the maximum overpressure in a model rotected by combat clothing and the protective plate can be reduced by 95%. However, the propagation speed of the shock wave within the simplified torso model increases from 1535.5 m/s to 2204.5 m/s. This shows that even protective equipment, which is not primarily intended to protect against blast, offers a significant reduction in the pressure load in the protected area. On the one hand it is caused by the media transition from air to PE and the resulting higher reflection of the acceleration of the transmitted wave within the simulant. On the other hand, it is also reduced due to the damping and dispersion caused by the clothing layers.
Im Projekt InnoBOSK wurden insgesamt vier wissenschaftlich basierte Bedarfserhebungsworkshops durchgeführt. Die Workshops hatten jeweils thematische Schwerpunkte und wurden mit Vertretern unterschiedlicher BOS (Behörden und Organisationen mit Sicherheitsaufgaben) durchgeführt.
In der vorliegenden Arbeit werden die erhobenen Bedarfe ausgewertet.
In this paper, we present an autonomous aerial robot to reconstruct tomographic 2D slices of gas plumes in outdoor environments. Our platform, the so-called Unmanned Aerial Vehicle for Remote Gas Sensing (UAV-REGAS) combines a lightweight Tunable Diode Laser Absorption Spectroscopy (TDLAS) sensor with a 3-axis aerial stabilization gimbal for aiming on a versatile octocopter. The TDLAS sensor provides integral gas concentration measurements but no information regarding the distance traveled by the laser diode's beam or the distribution of the gas along the optical path. We complemented the set-up with a laser rangefinder and apply principles of Computed Tomography (CT) to create a model of the spatial gas distribution from these integral concentration measurements. To allow for a rudimentary ground truth evaluation of the applied gas tomography algorithm, we set up a unique outdoor test environment based on two 3D ultrasonic anemometers and a distributed array of 10 infrared gas transmitters. We present first results showing the 2D plume reconstruction capabilities of the system under realistic conditions.
Regelmäßig werden Einsatzkräfte der Feuerwehr bei Brandeinsätzen mit brand- bzw. wärmebeaufschlagten Druckgasbehältern konfrontiert. Aufgrund ihrer großen Verbreitung handelt es sich dabei oftmals um Propan- oder Acetylengasflaschen. Propangasflaschen mit Füllmengen bis 33 Kilogramm sind in flächendeckender Verwendung zum Beispiel in Handwerksbetrieben, Produktionsbereichen, Baustellen und Restaurants, werden aber oftmals auch zum Heizen und Kochen im Privatbereich verwendet. Acetylengasflaschen sind in Verbindung mit entsprechenden Sauerstoffbehältern ebenso in Werkstätten, gewerblichen Anlagen und auf Baustellen zum Autogenschweißen und thermischen Trennen in vielfacher Verwendung. Beide Arten von Druckgasbehältern sind darüber hinaus auch im Straßenverkehr als Gefahrgut und in kleineren Mengen auch als private Fracht anzutreffen. Die Deutsche Gesetzliche Unfallversicherung (DGUV) hat zusammen mit weiteren Experten als Hilfestellung und aufgrund neuer wissenschaftlicher Erkenntnisse zwei DGUV-Informationen für Einsatzkräfte zum Umgang mit wärmebeaufschlagten Druckgasbehältern erstellt.