Filtern
Erscheinungsjahr
- 2007 (15) (entfernen)
Dokumenttyp
- Vortrag (6)
- Zeitschriftenartikel (4)
- Beitrag zu einem Tagungsband (3)
- Posterpräsentation (2)
Schlagworte
- Cleaning (3)
- Laser (3)
- Laser ablation (2)
- Silk (2)
- Textiles (2)
- Amorphous (1)
- Diamond-like carbon (1)
- Ellipsometrie (1)
- Glass transitions (1)
- Glasses (1)
Eingeladener Vortrag
- nein (6)
Single- and multi-shot ablation thresholds of gold films in the thickness range of 311400 nm were determined employing a Ti:sapphire laser delivering pulses of 28 fs duration, 793 nm center wavelength at 1 kHz repetition rate. The gold layers were deposited on BK7 glass by an electron beam evaporation process and characterized by atomic force microscopy and ellipsometry. A linear dependence of the ablation threshold fluence Fth on the layer thickness d was found for d ≤ 180 nm. If a film thickness of about 180 nm was reached, the damage threshold remained constant at its bulk value. For different numbers of pulses per spot (N-on-1), bulk damage thresholds of ~0.7 J cm-2 (1-on-1), 0.5 J cm-2 (10-on-1), 0.4 J cm-2 (100-on-1), 0.25 J cm-2 (1000-on-1), and 0.2 J cm-2 (10000-on-1) were obtained experimentally indicating an incubation behavior. A characteristic layer thickness of Lc 180 nm can be defined which is a measure for the heat penetration depth within the electron gas before electronphonon relaxation occurs. Lc is by more than an order of magnitude larger than the optical absorption length of α-1 12 nm at 793 nm wavelength.
Optical multimode fibers are applied in materials processing (e.g. automotive industry), defense, aviation technology, medicine and biotechnology. One challenging task concerning the production of multimode fibers is the enhancement of laser-induced damage thresholds. A higher damage threshold enables a higher transmitted average power at a given fiber diameter or the same power inside a thinner fiber to obtain smaller focus spots.
In principle, different material parameters affect the damage threshold. Besides the quality of the preform bulk material itself, the drawing process during the production of the fiber and the preparation of the fiber end surfaces influence the resistance. Therefore, the change of the laser-induced damage threshold of preform materials was investigated in dependence on a varying thermal treatment and preparation procedure.
Single and multi-pulse laser-induced damage thresholds of preforms (F300, Heraeus) were measured using a Q-switched Nd:YAG laser at 1064 nm wavelength emitting pulses with a duration of 15 ns, a pulse energy of 12 mJ and a repetition rate of 10 Hz. The temporal and spatial shape of the laser pulses were controlled accurately.
Laser-induced damage thresholds in a range from 150 J cm-2 to 350 J cm-2 were determined depending on the number of pulses applied to the same spot, the thermal history and the polishing quality of the samples, respectively.
Hydrogen-Containing Amorphous Carbon Layers as Optical Materials in the Near-IR Spectral Range
(2007)
Hydrogenated amorphous carbon layers were deposited on various substrates by means of a plasma CVD process with a RF substrate bias as well as an ECR plasma source. The optical properties of the a-C:H layers were obtained via spectroscopic ellipsometry and correlated with their mechanical and chemical properties. The layers from pure RF plasma exhibit a higher absorption constant in the visible spectral range and a higher refractive index. All layers are nearly transparent in the NIR spectral range making them candidates for optical thin layer systems. The laser damage behaviour of the a-C:H layers was investigated with ultrashort pulses. The damage thresholds were consistent with the absorption constants of the layers. Interesting damage morphologies were observed indicating a sensitivity of this experiment to sub-structures in the layer.
Laser-induced damage threshold (LIDT) testing of oxide and metal coatings with sub-30 fs pulses
(2007)
Analyse häufig verwendeter europäischer Papiere. Im Fokus: Fasermaterial, Füllstoffe und Leimung
(2007)
Restauratoren können verschiedene Papierarten mit dem bloßen Auge aufgrund von Merkmalen in der Textur und der Oberflächenbeschaffenheit, seinem Aussehen im Durchlicht sowie an Griff und Klang grob unterscheiden. Dabei ist sich der Restaurator stets der Tatsache bewusst, dass es sich lediglich um eine erste grobe Einschätzung handeln kann. Erst bei mikroskopischen Analysen und physikalischen Experimenten treten Charakteristika zu Tage, die eine weitere Annäherung an die Zusammensetzung des Papiers und damit seiner Provenienz erlauben. Gegenstand dieser Arbeit war es, ein europäisches Hadernpapier, ein holzhaltiges Zeichenpapier und ein Whatman®-Filterpapier mit zwei mikroskopischen Methoden und einer Verbrennungstechnik zu untersuchen. Das Fasermaterial, die Füllstoffe, die Leimung und eventuelle Verunreinigungen wurden detailliert evaluiert. Neben konventioneller Lichtmikroskopie kam die weniger bekannte Umweltrasterelektronenmikroskopie (ESEM = Environmental Scanning Electron Microscopy) zum Einsatz, die neben der bildlichen Darstellung der Probenoberflächen zusätzlich eine Elementanalyse derselben gestattet. Letzteres erfordert allerdings das Vorhandensein eines zusätzlichen Röntgenspektrometers. Darüber hinaus wurden die verschiedenen Papiere trocken verascht. Es wurde eine oxidative Zerstörung der organischen Stoffe gewährleistet bis nur noch nichtbrennbare mineralische Asche zu verzeichnen war. Die Komplementarität der eingesetzten Methoden wird demonstriert und ein Einblick in die Zusammensetzung und Struktur der Papiere ermöglicht. Die Analysemethoden sind durch ihren partiell zerstörenden Charakter bzw. Limitierungen hinsichtlich der Objektgröße nur bedingt für die Untersuchung am Original geeignet, sehr wohl aber dafür, das Probenmaterial für Versuchsreihen genau zu definieren und zu standardisieren.