Filtern
Erscheinungsjahr
Dokumenttyp
- Beitrag zu einem Tagungsband (17)
- Vortrag (16)
- Zeitschriftenartikel (7)
- Beitrag zu einem Sammelband (7)
- Buchkapitel (2)
- Forschungsbericht (1)
Referierte Publikation
- nein (50) (entfernen)
Schlagworte
- Druckbehälter (7)
- Schallemissionsprüfung (7)
- Acoustic emission (6)
- Schallemission (6)
- Röntgenrefraktionsmessung (3)
- Composite (2)
- Ermüdungsrisswachstum (2)
- Faserkunststoffverbund (2)
- Faserverbundwerkstoffe (2)
- Korrosion (2)
Eingeladener Vortrag
- nein (16)
Acoustic emission
(2013)
Mode I fracture toughness tests on Double Cantilever Beam specimens from carbon-fibre and glassfibre reinforced polymer-matrix composites were monitored with Acoustic Emission (AE) and loaddisplacement traces and delamination lengths were recorded. AE characterized the kinetics of delamination propagation. The progress of AE activity and AE intensity with load and AE source location plots are used to determine the delamination onset on the microscopic and macroscopic scale.
Energy dissipating processes initiated in the damage zone near the delamination tip. Low Interface adhesion results in lower debonding stresses and larger damage zones compared with composites with good adhesion. Time-dependent linear location of AE sources yields the average length of the damage zone and the average speed of delamination propagation. Parameter analysis has been used empirically for identifying AE source mechanisms. A new Classification Software for transient AE waveforms permits identification of the source mechanism of individual AE signals. A micro-mechanical fracture model based on the AE results describes the contributions of microscopic matrix and Interface mechanisms to the interlaminar fracture energy.
A comparative analysis of selected standards and guidelines on Acoustic Emission testing published by international and national organisations yields an assessment of the current status of standardisation. Areas where existing documents do not yet exist or appear unsatifactory for some reason are identified and formulated as perspectives for further work. In the future, structural integrity assessment with Acoustic Emission methods is expected to gain in importance.
Pipelines and industrial piping systems are particularly relevant regarding technical safety, availability and maintenance. Large flow rates of hazardous substances imply that even smallest leakages can lead to high environmental impacts. Therefore, and to ensure the availability of infrastructure, an early detection and localization of potentially hazardous degradations to the walls (e.g. cracks, pittings, sedimentation, etc.) of the containments is necessary. However, in many cases it is not feasible to equip pipelines with a large number of point sensors at reasonable expense.
The principle of distributed fibre optic sensing relies on one single optical fibre, which simultaneously acts as a spatially continuous sensor as well as the signal transducer. Therefore, extensive structures can be provided with this type of sensor with comparatively low efforts.
As a consequence, monitoring oil and gas pipelines using distributed fibre optic sensors is on the upswing. Besides the established methods to measure temperature and strain, distributed acoustic sensing (DAS) has lately received considerable attention as a means to detect and localize third party threats to pipelines (approach of vehicles, digging, mechanical manipulation).
The so far not utilized potential of DAS as a means for continuous condition monitoring of pipes by detecting and localizing acoustic signals that point to certain damage scenarios, is currently under investigation in an interdisciplinary research project at BAM (AGIFAMOR, Ageing Infrastructures – Fibre Optic Monitoring of Pipes).
In order to qualify distributed acoustic fibre optic sensors for this application area, we especially focus on detecting and identifying the relevant acoustic emissions of interesting degradations as well as on the optimal way of application of the optical fibres to the specimen to achieve an optimal signal transmission of acoustic signals.
Die Restlebensdauerabschätzung von Faserkunststoffverbunden ist ein ungelöstes
Problem. Die Beobachtung der Matrixschädigung ist dabei ein vielversprechender Ansatz zur Bewertung des Schädigungszustandes insgesamt. Unter kombinierter Beobachtung mit Röntgenrefraktionsmessungen und Schallemissionsmessung wurden uni- und biaxiale Lasten statisch und zyklisch auf Kohlenstofffaserepoxidharz-Proben aufgebracht. Die uniaxiale Belastung erfolgt mittels einer eigenentwickelten Kompaktprüfmaschine direkt während der Röntgenrefraktions- und Schallemissionsmessung in der Röntgenkammer. Die biaxiale Belastung wird an Modelldruckbehältern ebenfalls mit Schallemissionsmessung durchgeführt. Hier wird der Modelldruckbehälter mit dem Röntgenrefraktionsverfahren periodisch inspiziert.