Filtern
Erscheinungsjahr
- 2018 (190) (entfernen)
Dokumenttyp
- Vortrag (91)
- Beitrag zu einem Tagungsband (38)
- Zeitschriftenartikel (25)
- Posterpräsentation (24)
- Buchkapitel (6)
- Zeitschriftenheft (Herausgeberschaft für das komplette Heft) (3)
- Monografie (1)
- Dissertation (1)
- Sonstiges (1)
Schlagworte
- Gefahrgut (9)
- Metal seal (9)
- Database (8)
- Datenbank (8)
- Fachinformationssystem (8)
- Composite (7)
- Creep (7)
- Degradation (7)
- Specialised Information System (7)
- Dangerous Goods (6)
Organisationseinheit der BAM
- 3 Gefahrgutumschließungen; Energiespeicher (190) (entfernen)
Eingeladener Vortrag
- nein (91)
Defining a Reduced Volume Zone for the Simulation of Burst Test on a Composite Pressure Vessels
(2018)
The random nature of fibre break in composite materials has to be modelled in all part of the structure as it may contain millions of fibres. The reduced volume method was introduced to determine a smaller zone where we could characterise the strength based on the accumulation of fibre break, hence increasing the computation time
The developed model has certain limitations of the element size to be used in the simulation to characterise the strength of composite materials. A reduced volume method is proposed in order to reduce the number of degree of freedom of the finite element simulation.This study has revealed certain configuration to be followed to speed up the computation time.
During dynamic processes, a certain range of strain rates is often observed along loaded structures and components. For precise numerical simulations, it is necessary to determine rate-dependent properties in dynamic tests and to describe the material behavior correctly within an appropriate domain of strain rates including adiabatic heating effects at higher strain rates, typically higher than 10 1/s. In principle, numerical simulations are compared to experimental results to verify the applied material models. For dynamic tensile tests considering ductile materials and large plastic deformation beyond uniform elongation, it is challenging to obtain comparable results due to plastic instability and necking of the specimen, e.g..
Based on the strain gradient in a general tensile specimen, a theoretical criterion was derived describing the plastic instability in rate-dependent materials under isothermal conditions in. It was applied to different multiplicative and additive constitutive relations and the analytical onset of necking was compared to results from numerical calculations of quasi-static and dynamic tensile tests. The simulations of a sheet-metal specimen with rectangular cross-section were carried out using the Finite Element Method and it was found that the numerical calculated and the theoretical predicted onset of plastic instability agree very good. The analytical criterion for instability holds even for specimens without geometrical or material imperfections and confirms that the onset of plastic instability must be considered a material characteristic.
However, real dynamic problems with higher strain rates are not isothermal, the heat generated by plastic work is not dissipated to the surrounding and the temperature of the material increases significantly. Adiabatic heating and thermal softening must be considered within the constitutive relations of rate-dependent materials and the discussion of plastic instability. In this paper, an enhanced and more generalized approach for the description of the condition for stability is discussed and applied to phenomenological as well as more physical constitutive relations from the literature. This allows an individual assessment of the accuracy and verification of rate-dependent material models with respect to plastic instability.
Defining a reduced volume zone for the simulation of burst test on composite pressure vessels
(2018)
The developed model uses a Monte-Carlo simulation to evaluate the accumulation of fibre breaks on composite structures. As the micromechanical aspects affecting the accumulation process is evaluated within a particular finite element size (0.1 mm x 0.1 mm x 8 mm), the industries would not be able to use the model on a real-size structure. Therefore, the reduced volume method is used to provide the statistical information between the required number of elements and simulations.
Component and material investigations on metal seals for high level radioactive waste containers
(2018)
Long-term investigations performed at BAM look to extend the state of knowledge on safety-related components of interim storage containers. Metal seals act as the primary sealing barrier in the bolted double lid closure system of the containers. The behaviour of metal seals has been investigated for ageing times up to 8.5 years and for various temperatures. The main cause for reduction in useable resilience overtime was due to creep deformation of the outer jacket of the seal.
For the long-term storage of spent nuclear fuel and other high-Level radioactive waste, dual purpose casks for the transportation and storage are widely used. Usually, these casks consist of a thick-walled monolithic cask body and a bolted double barrier lid System equipped with metal seals (consisting of an inner helical spring and two outer metal layers with a total cross-section diameter between 5 and 10 mm) to ensure the long-term safe confinement of the radioactive inventory.
Based on analytical and experimental studies, such metallic Systems have been qualified of storage periods of up to four decades so far as long as proper manufacturing and assembling conditions are met. More than 20 years of Operation experience with a permanently increasing number of casks has shown full compliance with the expectations.
In the meantime many countries have to face a significant delay of establishing a high-level radioactive waste repository what leads to Need for extending interim storage periods for probably 60, 80 or 100 years.
For that reason the long-term performance of metal seals for such time periods is of specific internst to demonstrate their sufficient safety function and specific investigations have already been launched, e.g. by BAM, to gain more experimental data and to develop validated models to extrapolate the seal performance to longer periods of time and or requested temperature levels.
The interaction between the package lid system and internal Content during mechanical drop testing is a decisive matter in evaluating Impact loads and the safety of the package. In the case of movable contents ist impact onto the inner side of the package lid can cause additional load peaks on the lid and the lid bolts. Some aspects of this issue were discussed on the basis of experimental results from instrumented drop tests with transport casks and on the basis of analytical approaches.
Packages for the transport of spent nuclear fuel shall meet the International Atomic Energy Agency regulations to ensure safety under different transport conditions. The physical state of spent fuel and the fuel rod cladding as well as the geometric configuration of fuel assemblies are important inputs for the evaluation of package capabilities under these conditions. In this paper, the mechanical behavior of high burn-up spent fuel assemblies (> approx. 50 GWd/tHM, value averaged over the fuel assembly) under transport conditions is analyzed with regard to the assumptions which are used in the Containment and criticality safety analysis. In view of the complexity of the interactions between the fuel rods as well as between the fuel assemblies, basket, and cask containment, the exact mechanical analysis of such phenomena is nearly impossible. Additionally, the gaps in information concerning the material properties of cladding and pellet behavior, especially for the high burn-up fuel, make the analysis more complicated. Considerations and knowledge gaps for the transport after extended interim storage are issues of growing interest. In this context, practical approaches are discussed based on the experience of BAM within the safety assessment of packages approved for transport of spent nuclear fuel.
The use of glass-fiber reinforced plastic (GRP) can reduce the weight of tanks significantly. By replacing steel with GRP in tanks for gases (propane, etc.) a weight reduction of up to 50 % was reached. In this project not only the material should be optimized, but also the design. Previous tanks consist of a double-walled structure with an insulation layer between the two shells (e.g. vacuum). Goal of this project is to realize a single-walled construction of GRP with an insulation layer on the outside.
To determine the temperature dependent material values, two different experiments are performed: In the first experiment, temperature dependent material properties of liquid nitrogen found in literature research are validated in a simple setup. The level of liquid nitrogen in a small jar is measured over the experiment time. Numerical simulation shows the change of nitrogen level with sufficient precision. In the second experiment, a liquid nitrogen is applied on one side of a GRP plate. Temperature is measured with thermocouples on top and bottom of the GRP plate, as well as in the middle of the plate. By use of numerical simulation, temperature dependent thermal conductivity is determined.
In the third experiment, a test stand is designed to examine different insulation materials. In this test stand, the insulation material can easily be changed. A numerical simulation, in which the determined material data is used, is performed as well for this test stand.
The experiments show, that GRP can be used in cryogenic environments. Multiphase simulations are a suitable tool to describe the energy absorption of thermal energy due to thermal phase change. Results on different insulation materials will follow.
Optical and thermal analysis of PVB encapsulant polymer functionalized with luminescent organic dyes
(2018)
This work focused on the technology of luminescent down shift (LDS), with a primary aim to identify and investigate a methodology to introduce the luminescent organic dye into PVB polymer encapsulant as emergent material for photovoltaic application. For this goal, we propose to study the feasibility to implement the LDS functionality and to identify suitability of available luminescent to be incorporated into the host polymer encapsulant material. The first step to this direction was through a comprehensive optical study of Violet 570 (V) organic dye in ethanol solvent. The methodology and experimental conditions such as laboratory polymer preparation and luminescence dye concentration were presented. Also, the emergent polymer encapsulant sheets were characterized by using optical and thermal analysis techniques. The absorption spectrum of the prepared PVB material shifts towards longer wavelengths, with increasing organic dye concentration.
Gefahrgut darf nur in speziell dafür zugelassenen Umschließungen (Verpackungen, IBC, Großverpackungen etc.) transportiert werden. Die BAM ist in Deutschland die zuständige Behörde für die Erteilung von Zulassungen, für die (Baumuster-)Prüfung von Gefahrgutverpackungen sowie die Anerkennung der Qualitätssicherungsprogramme, nach denen die Gefahrgutverpackungen zu fertigen sind. Hierfür erlässt die BAM sogenannte BAM-GGRs (Gefahrgutregeln).
Für den Transport von Lithium-Batterien sind verschiedene Vorschriften des Transportrechts zu beachten. Insbesondere für defekte und beschädigte Lithium-Batterien, die beim Transport gefährlich reagieren, in Brand geraten oder giftige Gase freisetzen können, werden in 2019 neue Regelungen anwendbar sein. Die BAM ist in Deutschland zuständige Behörde für deren Umsetzung.
Defective or damaged Lithium batteries may react dangerously during transport. Requirements for the safe transport of such batteries have been developed at UN level. They are adopted in the respective transport regulations. BAM as competent authority has the task to interpret those regulations and has developed procedures for testing and approval.
After restarting the site selection process for a final repository for spent nuclear fuel (SNF) and heat-generating radioactive waste, all areas with one of the three potential host rock formations considered in Germany – salt, clay and crystalline rock – are under review. The project “KoBrA“, run by BGE TECHNOLOGY and BAM, collects and reviews requirements, criteria and proposals for final disposal container concepts complying with the current safety standards, taking into consideration international experience in the field of high-level nuclear waste (HLW) management.
Accident safe packages for the transport of spent nuclear fuel and high-level waste shall fulfil international IAEA safety requirements. Compliance is shown by consecutive mechanical and thermal testing. Additional numerical analysis are usually part of the safety evaluation. For damage protection some package designs are equipped with wood filled impact limiters encapsulated by steel sheets. The safety of these packages is established in compliance with IAEA regulations. Cumulative mechanical and fire tests are conducted to achieve safety standards and to prevent loss of containment. Mechanical reliability is proven by drop tests. Drop testing might cause significant damage of the impact limiter steel sheets and might enable sufficient oxygen supply to the impact limiter during the fire test to ignite the wood filling. The boundary conditions of the fire test are precisely described in the IAEA regulatory. During the test the impact limiter will be subjected to a 30 minute enduring fire phase. Subsequent to the fire phase any burning of the specimen has to extinguish naturally and no artificial cooling is allowed. At BAM a large-scale fire test with a real size impact limiter and a wood volume of about 3m3 was conducted to investigate the burning behaviour of wood filled impact limiters in steel sheet encapsulation. The impact limiter was equipped with extensive temperature monitoring equipment. Until today burning of such impact limiters is not sufficiently considered in transport package design and more investigation is necessary to explore the consequences of the impacting fire. The objective of the large scale test was to find out whether a self-sustaining smouldering or even a flaming fire inside the impact limiter was initiated and what impact on the cask is resulting. The amount of energy, transferred from the impact limiter into the cask is of particular importance for the safety of heavy weight packages. With the intention of heat flux quantification a new approach was made and a test bench was designed.
Das Monte-Carlo-Experiment ermöglicht die numerische Simulation von statistischen Grundgesamtheiten und somit auch die Generierung von Festigkeitswerten für eine genau definierte Population von Druckgefäßen. In diesem Beitrag wird möglichst nachvollziehbar gezeigt, wie Werte generiert, Stichproben gezogen und ausgewertet werden. Auf dieser Basis wird auch gezeigt, wie die Wahrscheinlichkeit ermittelt wird, mit der Stichproben aus simulierten Populationen das Zulassungskriterium „Mindestberstdruck“ bestehen.
Derzeit existieren für Gefahrgutverpackungen in den internationalen Gefahrgutvorschriften keine Festlegungen für quantitative Grenzleckageraten, die sich an Sicherheitsbetrachtungen während der Beförderung orientieren. Für die Dichtheitsprüfung im Rahmen der Bauartzulassung von Gefahrgutverpackungen für flüssige Füllgüter ist das Standardprüfverfahren das Eintauchverfahren in Wasser („Bubble Test“). Hierbei handelt es sich um ein lokalisierendes Prüfverfahren. Seine Anwendung lässt keine quantitative Aussage darüber zu, ob unter Beförderungsbedingungen aufgrund von strömungsbedingter Stofffreisetzung durch Leckstellen der Gefahrgutverpackungen die Gefahr der Bildung einer explosionsfähigen Atmosphäre besteht. Ziel der vorliegenden Untersuchungen ist daher, zunächst quantitative Dichtheitsanforderungen an Gefahrgutverpackungen im Hinblick
auf die Entstehung explosionsfähiger Dampf-Luft-Gemische während des
Transports zu entwickeln. Im Anschluss werden strömungsbedingte Leckageraten der Verschlüsse verschiedener Bauarten von Gefahrgutverpackungen gemessen. Der Vergleich der Messwerte mit den berechneten Grenzwerten ermöglicht die Einschätzung hinsichtlich der Bildung einer explosionsfähigen Atmosphäre. Dieser quantitative Ansatz zur Beurteilung der Dichtheit ist für Gefahrgutverpackungen derzeit noch nicht etabliert.
Die quantitative Leckageratenmessung der Gefahrgutverpackungen wird mit dem Überdruckverfahren mit Ansammlung (Akkumulationsverfahren) unter Verwendung von Helium als Prüfgas vorgenommen. Zusätzlich erfolgt die Detektion weiterer potentieller Leckstellen außerhalb des Verschlussbereiches mit dem Schnüffelverfahren. Bei allen untersuchten Bauarten, mit Ausnahme des 6 L-Feinstblechkanisters, ist der Verschluss die einzige systematische Leckstelle der Verpackung. Die Messung der Helium-Leckageraten und der anschließende Vergleich mit den berechneten Helium-Grenzleckageraten zeigt, dass folgende Bauarten hinsichtlich des Erreichens der unteren Explosionsgrenze (UEG) durch eine Leckageströmung als kritisch einzuschätzen sind: Kunststoffverpackungen mit Schraubverschlüssen mit Flachdichtung, wenn bei diesen bestimmte Schädigungsmuster im Verschlussbereich vorliegen; Feinstblechkanister, da bei ihnen nicht nur der Verschlussbereich eine Leckstelle darstellt; Kunststoffverpackungen mit Schraubverschlüssen mit Flachdichtung, wenn diese auch für Füllgüter der Verpackungsgruppe I zugelassen sind. Als Konsequenz sollten bei diesen kritischen Bauarten entweder Modifikationen in Bezug auf die Verpackung selbst oder auf die Transportbedingungen im Frachtcontainer vorgenommen werden.
Im folgenden Beitrag wird im Rahmen einer Abnahme vor Inbetriebnahme eines 18 000 Liter fassenden glasfaserverstärkten Kunsstofftanks (GFK-Tank) der integraler Mittelwert einer GFK Tankwandung einem detaillierten Lagenaufbau gegenübergestellt. Ziel ist es, den komplexen Lagenaufbau einer Tankwandung möglichst einfach abzubilden. Dazu werden die notwendigen Materialeigenschaften als integraler Mittelwert berücksichtigt. Die Ergebnisse der Finite Elemente Analysen (FEA) werden dann mit den Messwerten der Dehnungsmessung validiert.
German packages for the transport of spent nuclear fuel are assessed with respect to specific transport conditions which are defined in the safety regulations of the International Atomic Energy Agency. In general, gastight fuel rods constitute the first barrier of the containment system. The physical state of the spent fuel and the fuel rod cladding as well as the geometric configuration of the fuel assemblies are important inputs for the evaluation of the package safety under transport conditions. The objective of this paper is to discuss the methodologies accepted by German authority BAM for the evaluation of spent fuel behavior within the package design approval procedure. Specific test conditions will be analyzed with regard to assumptions to be used in the activity release and criticality safety analysis. In particular the different failure modes of the fuel rods, which can cause release of gas, volatiles, fuel particles or fragments, have to be properly considered in these assumptions. The package as a mechanical system is characterized by a complex set of interactions, e.g. between the fuel rods within the assembly as well as between the fuel assemblies, the basket, and the cask containment. This complexity together with the limited knowledge about the material properties and the variation of the fuel assemblies regarding cladding material, burn-up and the operation history makes an exact mechanical analysis of the fuel rods nearly impossible. The application of sophisticated numerical models requires extensive experimental data for model verification, which are in general not available. The gaps in information concerning the material properties of cladding and pellets, especially for the high burn-up fuel, make the analysis more complicated additionally, and require a conservative approach. In this context some practical approaches based on experiences by BAM within safety assessment of packages for transport of spent fuel will be discussed. Ongoing research activities to investigate SNF mechanical behavior in view of gas and fissile material release under transport loads are presented.
Packages for the transport and storage of radioactive materials are often sealed with elastomer or metal seals. These seals are basic components to meet the leak tightness criteria for these kind of packages. An overview over ongoing research and development concerning metal and elastomer seals is given in the presentation. Introductions in the fundamental functionality of elastomer and metal seals are presented. Ageing processes are shown for both components regarding to different ageing effects.
Heizöllagerbehälter aus Polyethylenformstoffen werden seit Beginn der 70-iger Jahre in Deutschland hergestellt. Die Hersteller empfehlen zur Gewährleistung der Sicherheit nach Ablauf von 30 Jahren den Ersatz dieser Behälter. Polyethylenformstoffe unterliegen im Laufe ihrer Nutzungsdauer der Alterung durch die Veränderung ihrer Eigenschaften. Das Ausmaß der Alterung und die Art des Abbauvorganges hängen im Wesentlichen vom chemischen Abbau des Polyethylens, der Wanddicke des Behälters und den Umgebungsbedingungen ab. Bisher lagen keine Untersuchungen zum Langzeitverhalten der Polyethylenformstoffe vor, insbesondere nach einer Nutzungsdauer der Tanks über 30 Jahre. Ziel der Untersu-chungen war, den tatsächlichen Schädigungsgrad der Polyethylenformstoffe im Vergleich zu den unbelasteten Formstoffen zu ermitteln. Da die BAM bis Mitte der 90-iger Jahre für die Prüfungen und Gutachten zur Zulassung dieser Behälter zuständig war, sind die Werkstoffdaten noch vorhanden.
Als Untersuchungsmethoden wurden die Bestimmung der Schmelze-Masse-Fließrate (MFR) und die Fourier-Transformation-IR-Spektroskopie (FTIR) von Tankausschnitten aus dem Bereich des Bodens, des Mantels und des Daches von 10 ausgesonderten Behältern aus den Polyethylenformstoffen A und B herangezogen. Die Messungen der MFR der Tankaus-schnitte aus diesen Bereichen zeigten Unterschiede in den Werten in Abhängigkeit vom Ge-wicht (5 kg oder 21,6 kg), welches eingesetzt wurde. Eine Abnahme der MFR-Werte wurde für die größere Anzahl der Tankwandungsausschnitte aus dem Formstoff B nach einer Lebensdauer der Tanks > 30 Jahre gemessen. Dieser Formstoff wurde hauptsächlich durch innere Alterung infolge Vernetzungen, Verzweigungen und Weichmacherverlust und weniger durch oxidativen Abbau geschädigt. Die FTIR-Messungen der Proben aus dem Bereich des Bodens und des Mantels der Tanks zeigten, dass die Intensität der asymmetrischen/symmetrischen CH2 -Streckschwingungen im Bereich: 2800 - 2900 cm-1 und der CH2 -Biegeverformungsschwingung bei 1400 cm-1 aufgrund von Kettenspaltungen zugenommen haben. Die Intensität der Carbonylstreckschwingung C=O bei 1740 cm-1 ist niedrig. Sie ist ein Maß für die Oxidation des Polymerwerkstoffes.
Die Bewertung der Werkstoffbeständigkeit ist von großer Bedeutung bei Änderung der Zusammensetzung der Kraftstoffe und des Heizöls, insbesondere die Frage nach der Beständigkeit der Dichtungswerkstoffe bei Zusätzen von Bioethanol und Biodiesel (Rapsölfettsäuremethylester).
Vorhergehende Untersuchungen (Messungen der Veränderungen der Masse, der Zugeigenschaften und der Härte) bezogen sich auf die Bewertung der Beständigkeit häufig verwendeter Dichtungswerkstoffe wie FKM, FVMQ, VMQ, EPDM, CR, CSM, IIR, PA, NBR und PUR in Kraftstoffen und Heizöl mit 10 % Biodiesel (nicht gealtert und bis zu 5 Jahre gealtert) unter statischen Bedingungen.
Ziel der Untersuchungen war die Bewertung der Beständigkeit von Fluorkautschuk unter verpressten Bedingungen in Analogie zu den Einsatzbedingungen in der Praxis. Die Masse und der Druckverformungsrest von Prüfkörpern aus FKM wurden vor und nach der Auslagerung über einen Zeitraum von 3, 7, 14, 28, 56 und 90 Tagen in E10 (Kraftstoff mit max. 10 % Ethanol), E85 (Kraftstoff mit 85 % Ethanol), Biodiesel (Rapsölfettsäuremethylester), Super (Kraftstoff mit max. 5 % Ethanol), Dieselkraftstoff mit max. 5 % Biodiesel, Super Plus (Kraftstoff ohne Ethanolzusatz) und Heizöl mit 10 % Biodiesel (B10) bei 40 °C gemäß ISO 815-1 bestimmt. Die Druckverformungsrestprüfung zählt neben der Messung der Härte, der Dichte und der Zugeigenschaften zu den wichtigsten Grundprüfverfahren der Elastomerindustrie. Nach Ende der Auslagerung in den Kraftstoffen und der Aufhebung der Verpressung wurde der Druckverformungsrest der Prüfkörper in regelmäßigen Zeitabständen bis zu einer Rücktrocknung > 90 Tage bestimmt. Zum Vergleich wurden Prüfkörper aus FKM ohne Kraftstoff oder Heizöl unter Verpressung bei 40 °C ausgelagert.
Die Masseänderung der Prüfkörper aus FKM betrug nach 90 Tagen Auslagerung in E10 9 %, in Super 8 %, in E85 4% und 0,6 % in Biodiesel. Die Erhöhung der Masse und die damit verbundene Quellung der Prüfkörper in E10 und Super mit 5 – 10% Ethanolzusatz hatte einen Einfluss auf den Druckverformungsrest, der sprunghaften Veränderungen unterlag im Vergleich zu den Werten nach Auslagerung in Biodiesel, Dieselkraftstoff und Heizöl B10 bei 40 °C. Zum Vergleich, unter statischen Bedingungen verringerte sich die Zugfestigkeit der Prüfkörper aus FKM nach Auslagerung in E10 bei 40 °C um 31 % und die Reißdehnung um 18 %.
Accident safe packages for the transport of spent nuclear fuel and high-level waste shall fulfil international IAEA safety requirements. Compliance is shown by consecutive mechanical and thermal testing. Additional numerical analysis are usually part of the safety evaluation. For damage protection some package designs are equipped with wood filled impact limiters encapsulated by steel sheets. The safety of these packages is established in compliance with IAEA regulations. Cumulative mechanical and fire tests are conducted to achieve safety standards and to prevent loss of containment. Mechanical reliability is proven by drop tests. Drop testing might cause significant damage of the impact limiter steel sheets and might enable sufficient oxygen supply to the impact limiter during the fire test to ignite the wood filling. The boundary conditions of the fire test are precisely described in the IAEA regulatory. During the test the impact limiter will be subjected to a 30 minute enduring fire phase. Subsequent to the fire phase any burning of the specimen has to extinguish naturally and no artificial cooling is allowed. At BAM a large-scale fire test with a real size impact limiter and a wood volume of about 3m³ was conducted to investigate the burning behaviour of wood filled impact limiters in steel sheet encapsulation. The impact limiter was equipped with extensive temperature monitoring equipment. Until today burning of such impact limiters is not sufficiently considered in transport package design and more investigation is necessary to explore the consequences of the impacting fire. The objective of the large scale test was to find out whether a self-sustaining smouldering or even a flaming fire inside the impact limiter was initiated and what impact on the cask is resulting. The amount of energy, transferred from the impact limiter into the cask is of particular importance for the safety of heavy weight packages. With the intention of heat flux quantification a new approach was made and a test bench was designed. A first computational simulation of transport package temperatures taking into account the results of the conducted fire test was performed.
Hydrogen is an attractive energy carrier that requires high effort for safe storage. For ensuring safety, they must undergo a challenging approval process. Relevant standards and regulations for composite cylinders used for the transport of hydrogen and for its onboard storage are currently based on deterministic (e.g. ISO 11119-3) or semi-probabilistic (UN GTR No. 13) criteria. This paper analysis the properties of such methods with respect to the evaluation of load cycle strength. Their characteristics are compared with the probabilistic approach of the BAM. Based on Monte-Carlo simulations, the available design range (mean value and scatter of strength criteria) of current concepts was exemplarily estimated. The aspect of small sample sizes is analysed and discussed with respect to the evaluation procedures.
Derzeit existieren für Gefahrgutverpackungen in den internationalen Gefahrgutvorschriften keine Festlegungen für quantitative Grenzleckageraten, die sich an Sicherheitsbetrachtungen während der Beförderung orientieren. Für die Dichtheitsprüfung im Rahmen der Bauartzulassung von Gefahrgutverpackungen für flüssige Füllgüter ist das Standardprüfverfahren das Eintauchverfahren in Wasser („Bubble Test“). Hierbei handelt es sich um ein lokalisierendes Prüfverfahren. Seine Anwendung lässt keine quantitative Aussage darüber zu, ob unter Beförderungsbedingungen aufgrund von strömungsbedingter Stofffreisetzung durch Leckstellen der Gefahrgutverpackungen die Gefahr der Bildung einer explosionsfähigen Atmosphäre besteht. Zentrales Ziel der vorliegenden Arbeit ist daher, zunächst quantitative Dichtheitsanforderungen an Gefahrgutverpackungen im Hinblick auf die Entstehung explosionsfähiger Dampf-Luft-Gemische während des Transports zu entwickeln. Im Anschluss werden strömungsbedingte Leckageraten der Verschlüsse verschiedener Bauarten von Gefahrgutverpackungen gemessen. Der Vergleich der Messwerte mit den berechneten Grenzwerten ermöglicht die Einschätzung hinsichtlich der Bildung einer explosionsfähigen Atmosphäre. Dieser quantitative Ansatz zur Beurteilung der Dichtheit ist für Gefahrgutverpackungen derzeit noch nicht etabliert. Die Grenzleckageraten werden für das Szenario des interkontinentalen Transports von Gefahrgutverpackungen in einem 20-Fuß-Frachtcontainer im Hinblick auf die untere Explosionsgrenze abgeleitet. Dies geschieht unter Annahme einer Worst-Case-Betrachtung für Beförderungsdauer, Beladung und Luftwechselrate. Als mittlere Beförderungstemperatur wird 30 °C angesetzt. Eine vollständige Durchmischung im freien Luftraum des Containers wird angenommen. Es werden drei repräsentative Baugrößen von Gefahrgutverpackungen gewählt, mit einem Volumen von ca. 6 L, ca. 60 L und ca. 220 L. Als Füllgüter werden die 23 meistbeförderten flüssigen Gefahrgüter betrachtet. Die treibende Kraft für die Strömung durch Leckstellen ist der sich in der Verpackung ausbildende Überdruck. Die Berechnung des Überdrucks erfolgt durch analytische Modellgleichungen in Abhängigkeit der spezifischen Stoffdaten, Füllgrad, Befülltemperatur, Transporttemperatur und Nachgiebigkeit der Verpackungsbauart. Die quantitative Leckageratenmessung der Gefahrgutverpackungen wird mit dem Überdruckverfahren mit Ansammlung (Akkumulationsverfahren) unter Verwendung von Helium als Prüfgas vorgenommen. Zusätzlich erfolgt die Detektion weiterer potentieller Leckstellen außerhalb des Verschlussbereiches mit dem Schnüffelverfahren. Bei allen untersuchten Bauarten, mit Ausnahme des 6 L-Feinstblechkanisters, ist der Verschluss die einzige systematische Leckstelle der Verpackung. Die Messung der Helium-Leckageraten und der anschließende Vergleich mit den berechneten Helium-Grenzleckageraten zeigt, dass folgende Bauarten hinsichtlich des Erreichens der unteren Explosionsgrenze (UEG) durch eine Leckageströmung als kritisch einzuschätzen sind: Kunststoffverpackungen mit Schraubverschlüssen mit Flachdichtung, wenn bei diesen bestimmte Schädigungsmuster im Verschlussbereich vorliegen; Feinstblechkanister, da bei ihnen nicht nur der Verschlussbereich eine Leckstelle darstellt; Kunststoffverpackungen mit Schraubverschlüssen mit Flachdichtung, wenn diese auch für Füllgüter der Verpackungsgruppe I zugelassen sind. Als Konsequenz sollten bei diesen kritischen Bauarten entweder Modifikationen in Bezug auf die Verpackung selbst oder auf die Transportbedingungen im Frachtcontainer vorgenommen werden. Bei Kunststoffverpackungen ist auch die Füllgutpermeation als Freisetzungsmechanismus relevant. Es wird der prinzipielle Rechenweg zur Berücksichtigung dieses Quellterms exemplarisch gezeigt. Diese Arbeit leistet einen grundlegenden Beitrag für die Etablierung einer systematischen quantitativen Dichtheitsbetrachtung von Gefahrgutverpackungen mit dem Ziel der Verbesserung der Sicherheit beim interkontinentalen Gefahrguttransport im Frachtcontainer.
THz and mid IR spectroscopy of high-molecular PE (HMW) and ultra high-molecular PE (UHMW) reveals modifications of the molecular structure. Characteristic absorption bands are changed if the two materials are exposed by γ-Co60 radiation up to 600 kGy and subsequently stored at an annealing temperature of 398 K until for 729 days.
To reduce the emission of CO2, liquified natural gas (LNG) is used as fuel. As the pipeline network is not developed all around the globe, LNG needs to be transported via ship or truck. Double-walled tanks made of steel with a vacuum insulation are currently used to keep LNG at cryogenic temperatures (-162 °C; 111 K). The double-walled construction makes the tanks heavy and expensive. Furthermore, there are some restriction to carry out in-service inspection using a double-wall design. Main topics: Lightweight design, superior thermal properties of GRP compared to steel Aim of this project is to develop a single-walled tank made of glass-fiber reinforced plastic (GRP) and an insulator, so that the tank pressure will not exceed 5 bar within a certain time, relative, as a result of the rising fluid temperature. First, the thermal and mechanical properties of GRP and the insulator at cryogenic temperatures must be determined. Liquid nitrogen (-196 °C; 77 K) is used for all experiments at cryogenic temperatures for safety reasons. Mechanical properties are analyzed by performing 3-point bending tests on cooled specimen. The tests show, that there are now significant changes on the mechanical properties of GRP, so that this material can be used in a cryogenic environment. To examine the thermal conductivity of GRP, a test rig is designed, in which one side of a GRP-laminate plate is cooled down while the other side is at room temperature at the beginning. Temperature is measured on both sides of the plate as well as inside the laminate. The temperature curves are then implemented in a ANSYS simulation to calculate thermal material properties. The experiments show, that the thermal conductivity of GRP is much lower than the one of steel, but still not low enough to design a single walled tank without an additional insulation. Therefore, a closed GRP pipe with insolation inside is immersed in liquid nitrogen for a defined time. Sensors record the surface temperatures inside and outside the specimen, as well as between insulation and GRP. With the data gained in this experiment, another ANSYS model is done. For correct simulation of the heat transfer between insulation and liquid nitrogen (or LNG later), a fluid simulation is necessary, which simulates the phase change from liquid to gaseous nitrogen. After validation of the model, a parameter study in the material properties of the insulation is performed, until a satisfying setup is achieved.
The safety of any transport system depends on a multitude of conditions, parameters and circumstances. In this regard, the interaction of the carried Cargo with the carrying vehicle represents a factor influencing the overall safety of any transport. The effects of cargo on the vehicle have to do with the vibration or shifting of the cargo, affecting the lateral stability of the vehicles and the braking performance.
Such interaction has been associated to road crashes and maritime vehicles capsizing. Simulation of cargo-vehicle interaction thus represents an interesting Topic when a reduction in transport accidents is pursued. In this paper, the fundamentals principles for simulating the interaction of the liquid cargo and the carrying vehicle, is presented. In the case of a road transportation, the proposed simplified Simulation methodologies, show good agreement with a full-scale test.
The mechanical and thermal loadings associated with the routine, normal and accident conditions of transport can have a significant effect on the leak tightness of the containment system of transport casks for spent fuel and high radioactive waste. The containment systems of such transport casks usually include bolted lids with metallic or elastomeric seals.
Scaled cask models are often used for providing the required mechanical and thermal tests series. Leak tests have been conducted on those models.
It is common practice to use scaled component tests to investigate the influence of deformations or displacements of the lids and the seals on the standard leakage rate as well as to study the temperature and time depending alteration of the seals.
In this paper questions and open points of the transferability of scaled test results to the fullscale design of the containment system will be discussed.
Um ein verlässliches Ergebnis der Monte-Carlo-Simulation zu garantieren, muss die Zuverlässigkeit des Tools vor dessen Anwendung sorgfältig geprüft werden. In diesem Vortrag werden die Validierung der angenommenen Verteilungsfunktionen, die Vertrauensbereiche und die Grenzwerte der generierten Grundgesamtheit vorgestellt. Darauf aufbauend wird der Ablauf der gesamten Simulation von der Erzeugung der Zufall-Variablen bis hin zur Akzeptanzrate gezeigt.
Commidities and rail damage
(2018)
A roll-plane simplified model, representing the suspended body-cargo of a railway car, was developed to simulate thedynamic response of a railway car while subjectedto lateral acceleration derived from its traveling along curved tracks. The model provides the means to calculate the suspension forces, which are supposed to be transmitted to the bogie´s wheelset. For the analysis of the potential effect of such forces on the railway fatigue life, different performance measures were considered, under different concepts. A family of curves were produced to analyze the effect of the height of the center of gravity of the body-cargo system, on the different performance measures. The resultingdiagramswereused to assess the rail damage potentials offour different railway cars. Results suggest that the height of the center of gravity, associated to the different types of railway cars, nonlinearly and strongly affects the fatigue lifeof the rail, with the double stack car being the moreinfrastructure-aggressive. In this respect, experimental evidence should be provided about such remarkable effects, so as to supportsome operational recommendationsthat shouldbe taken to mitigate these effects, including, for example, the regulation of the traveling speed of some vehicles.
Commodities and rail damage
(2018)
The normalized contact-mechanics fourth-power law approach for the
dynamic loads, suggest: worst railway use situation (double deck at 65 km/h) is 350 times that of the less rail damage situation (flat car at 45 km/h).
The normalized dispersion approach for the dynamic loads (Dynamic Load Coefficient), suggest that the worst railway use situation (double deck at 65 km/h) is about 4 times that of the less rail damage Situation (flat car at 45 km/h).
The potential effect of the different types of cars on the railway fatigue life could be significant, as a function of the vehicle speed.
The experimental validation of these outputs will be carried out as a continuation of this research effort. In addition to that, it should be mentioned that the associated simplified model could be used to analyze some other situations, related with the transport safety of different products.
Die Monte-Carlo-Simulation ist eine geeignete Methode, um Festigkeitseigenschaften wie z.B. Berstdruck, oder auch die Lastwechselfestigkeit von ganzen Population von Druckbehältern zu simulieren.
Dies erlaubt wiederum die systematische Analyse der Wirksamkeit von deterministischen Mindestanforderungen und die Optimierung entsprechender Zulassungsvorschriften.
Seit zehn Jahren führt die Bundesanstalt für Materialforschung und -prüfung (kurz: BAM) auf zwei Prüfständen Brandprüfungen z. B. an Transport-und Lagerbehältern für radioaktive Stoffe oder zur Prüfung von Brandschutzbeschichtungen durch. Als Brandmedium wird Flüssiggas (Propan-Butan-Gemisch C) eingesetzt, mit dem die Prüfobjekte simulierten Unfallfeuern ausgesetzt werden. Seit Anfang 2018 verfügt die BAM darüber hinaus auch über einen Jetfire-Prüfstand, der die Anforderungen der ISO 22899-1:2007 1) erfüllt.
Low temperature performance of rubber seals - Influence of crystallite formation on seal performance
(2018)
Rubbers are widely used as sealing materials in various applications. In many fields the function of seal materials at low temperatures is necessary. Therefore, the understanding of failure mechanisms that lead to leakage at low temperatures is of high importance.
It is known that rubbers possess strongly temperature dependent material properties. At low temperatures high changes in the material properties are observed which can be caused by the rubber-glass transition (abbr. glass transition) or for some rubbers also by partial crystallisation at lower temperatures. During continuous cooling the material changes during rubber-glass transition from rubber-like entropy-elastic behaviour to stiff energy-elastic behaviour. In case of (thermal-) crystallisation the formed crystallites act as additional (physical) crosslinks within the material but the molecules in the amorphous phase can still behave like a rubber. Hence, rubbers are normally used above rubber-glass transition and (thermal-) crystallization temperature but the minimum working temperature limit is heavily depending on the application conditions. Therefore, the lower operation temperature limit of rubber seals is under investigation.
In the past we have investigated material properties and sealing behaviour of rubber seals at low temperatures. As the initial work was dedicated to purely static sealing conditions we started to investigate the effect of a small partial release of rubber seals at low temperatures to study the influence of dynamic events on leak tightness. In addition, other groups report on the influence of counterpart surface and adhesion.
In this contribution we focus on the difference between purely amorphous elastomers and elastomers which become partially crystalline at low temperatures. The influence of partial crystallization on the low temperature performance of rubber seals is discussed.
Häufig ist es wünschenswert, für neue Materialien oder Anwendungen künstliche Bewitterungsverfahren zu benutzen, die auf die spezifischen Anforderungen besser zugeschnitten sind, als es bei bestehenden standardisierten Verfahren der Fall ist. Nachdem man die spezifischen Parameter der Beanspruchung unter Anwendungsbedingungen und die spezifische Empfindlichkeit des Materials erfasst hat, beginnt ein Prozess, der als „Test Tailoring“ häufig abstrakt verwendet, auf den aber nur selten näher eingegangen wird. Genau dieser Prozess soll hier am Beispiel der Entwicklung eines künstlichen Bewitterungstests unter saurer Beaufschlagung, dem in der BAM entwickelten Acid Dew and Fog Test, beispielhaft erläutert werden.
Numerical approach to determine the correct puncture bar length for the IAEA puncture bar drop test
(2018)
Among other mechanical tests the 1 meter drop onto a steel puncture bar shall be considered for accident safe packages for the transport of radioactive material. According with the IAEA regulations “the bar shall be of solid mild steel of circular section, 15.0 ± 0.5 cm in diameter and 20 cm long, unless a longer bar would cause greater damage…”. The most damaging puncture bar length can be estimated by iterative processes in numerical simulations. On the one hand, a sufficient puncture bar length has to guarantee that shock absorbers or other attachments do not prevent or reduce the local load application to the package, on the other hand, a longer and thus less stiff bar causes a smaller maximum contact force. The contrary influence of increasing puncture bar length and increasing effective drop height shall be taken into account if a shock absorber is directly placed in the target area. The paper presents a numerical approach to identify the bar length that causes maximum damage to the package. Using the example of two typical package masses the sensitivity of contact forces and puncture bar deformations to the initial length are calculated and assessed with regard to the international IAEA package safety requirements.
The containment systems of transport casks for spent fuel and high radioactive waste usually include bolted lids with metallic or elastomeric seals.
The mechanical and thermal loadings associated with the routine, normal and accident conditions of transport can have a significant effect on the leak tightness of such containment system.
Scaled cask models are often used for providing the required mechanical and thermal tests series. Leak tests have been conducted on those models.
It is also common practice to use scaled component tests to investigate the influence of deformations or displacements of the lids and the seals on the standard leakage rate as well as to study the temperature and time depending alteration of the seals.
In this paper questions of the transferability of scaled test results to the full size design of the containment system will be discussed.
There was a need to validate the longitudinal performance required for the cargo securement, as current standards exhibit differences.
A model has been proposed in this paper, to simulate the effect of a shifting cargo on the braking efficiency of the vehicle. Results suggest that the braking efficiency can be greater in the case of a shifting cargo, as a result of the uncoupling of the cargo-vehicle systems, implying that similar braking forces are exerted on a reduced mass. The shifting of the cargo can occur as a result of the vibration of the vehicle, that leads to having a diminished friction force to prevent the shifting of the cargo.
The feasibility study „AGIFAMOR. Ageing infrastructures – distributed acoustic monitoring of pipes” is an interdisciplinary research project at BAM internally financed from 2015 to 2018. Therefore, the quite young fibre optic sensing technology of distributed acoustic sensing (DAS) was investigated to possibly be extended towards a global condition monitoring system for pipelines operating in real time.
DAS is a highly dynamic fibre optic sensing technology based on the method of coherent optical time domain reflectometry (C-OTDR). DAS allows capturing strain changes in the range of kHz. For the experimental work, the most suitable application yielding an optimum sensitivity was proven by wrapping a standard single-mode silica fibre around the pipe.
The DAS sensitivity was investigated regarding the detection of 1) incidents that initiate propagation of acoustic waves in the pipe wall, 2) changes inside the pipeline causing altered flow and 3) damage development in the pipe wall. Therefore, several testing setups in laboratory as well as in real scale were realized. For comparison purposes, experiments were accompanied by acoustic emission analyses and by measurements with accelerometers.
DAS was found to be very sensitive to gas ignition and its propagation across the pipe. Furthermore, the ability of DAS to detect and localize acoustic signals associated with pipeline leakage was demonstrated. The detection of crack formation and propagation within the pipe wall by means of DAS was studied during bending tests on several pipe segments, but was not proven so far with certainty. As expected, these studies turned out as the most difficult challenge due to the random occurrence and transient nature of microscopic damage phenomena.
There was a need to validate the longitudinal performance required for the cargo securement, as current standards exhibit differences. A model has been proposed in this paper, to simulate the effect of a shifting cargo on the braking efficiency of the vehicle. Results suggest that the braking efficiency can be greater in the case of a shifting cargo, as a result of the uncoupling of the cargo-vehicle systems, implying that similar braking forces are exerted on a reduced mass. The shifting of the cargo can occur as a result of the vibration of the vehicle, that leads to having a diminished friction force to prevent the shifting of the cargo.
Small and large-scale tests have been carried out Pressure vessel – to improve numerical modelling Different types of fire must be distinguished Modelling of vessels were discussed Test configuration has been developed to see what happens in the vessel First results encourage us to continue the Research Thermohydraulics needs further work (boundary layers).
Transport safety depends in great extent of what happens to the cargo once the carrying vehicle derails or rollovers. The exposure of tanks to direct fire is a condition that potentially involves catastrophic consequences. Studying the behavior of the contained fluid under these drastic circumstances, is critical to develop methods and techniques to mitigate the serious consequences of many mishaps. In this paper, the experimental potentials of a Particle Image Velocimetry data acquisition system are described, for providing experimental data that could be used to calibrate mathematical models. As an example of the situations that need to be modelled, an experiment is described concerning the effect of the boundary conditions and protecting devices, on the rate of variation of pressure and temperature of the fluid in a tank exposed to a direct fire. In this regard, the results emphasize the importance of equipping the vessels with both thermal insulation and safety valves.