Filtern
Erscheinungsjahr
- 2012 (22) (entfernen)
Dokumenttyp
Referierte Publikation
- ja (22) (entfernen)
Schlagworte
- Laser beam welding (5)
- Electromagnetic weld pool support (3)
- Gas metal arc welding (3)
- Lorentz force (3)
- Marangoni stresses (3)
- Natural convection (3)
- Corrosion (2)
- Instrumentierte Eindringprüfung (2)
- Punktschweißverbindung (2)
- Resistance spot welding (2)
- Stainless steel (2)
- Stress reduction (2)
- Weldability (2)
- Welding simulation (2)
- AZ31 magnesium alloy (1)
- Aluminium (1)
- Aluminium alloy (1)
- Austenitic (1)
- Austenitic stainless steels (1)
- Automotive industry (1)
- Beam welding (1)
- CO2 laser (1)
- CO2 lasers (1)
- Controlled tensile weldability test (1)
- Cracks (1)
- Critical strains (1)
- Deformation (1)
- Duplex (1)
- Duplex stainless steels (1)
- Electromagnetically controlled laser beam welding (1)
- Fatigue life (1)
- Finite element analysis (1)
- Fluid flow (1)
- Full penetration (1)
- GTA welding (1)
- Gap (1)
- Hardness (1)
- Hartmann effect (1)
- Heißrisse (1)
- High energy beam welding (1)
- High power laser beam welding (1)
- Hot cracking (1)
- Hot cracking test (1)
- Kornfeinung (1)
- Laser metal deposition (1)
- Laser powder cladding (1)
- Laser scanner optics (1)
- Laser welding (1)
- Lokale Festigkeit (1)
- Lokale Spannungs-Dehnungskurven (1)
- Manganese (1)
- Mechanical properties (1)
- Microstructure (1)
- Multi-pass welding (1)
- Numerical simulation (1)
- Ortsaufgelöst (1)
- Pores (1)
- Porosity prevention (1)
- Post-weld heat treatment (1)
- Post-welding heat treatment (1)
- Repair welding (1)
- Residual stress (1)
- Residual stresses (1)
- Schweißeignung (1)
- Sensitivity analysis (1)
- Shear strength (1)
- Shielding gases (1)
- Solidification cracking (1)
- Spannungs-Dehnungskurve (1)
- Spot welding (1)
- Stainless steels (1)
- Strain rates (1)
- Tack welding (1)
- Tensile strength (1)
- Tensileshear (1)
- Thermography (1)
- Ti-6Al-4 V (1)
- Torsion (1)
- V groove (1)
- WIG-Schweißen (1)
- Weld microstructure (1)
- Weld pool dynamics (1)
- Weld pool stabilization (1)
- Welding-induced distortion (1)
- Welding-induced residual stress (1)
- YAG lasers (1)
IIW-2326
Austenitic and austenitic-ferritic CrMnNi-stainless steels are suitable materials in the transport and automotive industry due to their high corrosion resistance and high strength that allows weight and cost savings. This study focuses on the laser weldability of a commercial lean duplex and an austenitic high manganese stainless steel. The impact of different laser sources, i.e. a 5 kW CO2- and a 4 kW Nd:YAG-laser, and of the main process parameters on the resulting weld quality will be investigated. One important aspect will concern the appearance of weld defects such as pores and hot cracks. The factors causing such internal imperfections will be analysed in order to find effective methods for preventing them. Weld microstructure and the associated corrosion and mechanical properties will be assessed with different techniques and adequate process parameters for high quality welds will be determined. The advantages and limitations of the applied welding processes will be evaluated for future applications.
Study of fatigue behavior for spot welded tensile shear specimens of advanced high strength steels
(2012)
For automotive body-in-white applications the influence of manufacture-related gaps between the steel sheets and also of manufacture-related surface cracks on the fatigue behavior of tensile shear specimens for spot welded TRIP steel was analyzed. It was shown that gaps between the steel sheets reduce the fatigue strength, whereas the fatigue behavior is neither influenced by cracks in the electrode indentation area nor in the heat effected zone.
In this study, the influence of production-related gaps on the shear tension strength and fatigue performance was investigated for resistance spot welded TRIP steel HCT690. Furthermore, the local strain distribution in shear tension test was calculated by the digital image correlation technique (DIC). The static shear tension strength was found to be almost independent of gaps up to 3 mm. The maximum local strain in the spot weld region however decreases depending on which sample side (deformed or undeformed) is considered. In addition, it has been ascertained that gaps of 3 mm lead to a significant drop in fatigue life compared to gap-free shear tension samples. This fact could be attributed to decreased stiffness, higher transverse vibration and higher rotation (θ) between the sheets as well as increased local stress calculated by 2 dimensional FE simulation.
In a repair process chain, damaged areas or cracks can be removed by milling and subsequently be reconditioned with new material deposition. The use of laser metal deposition has been investigated for this purpose. The material has been deposited into different groove shapes, using both stainless steel and Ti-6Al-4 V. The influence of welding parameters on the microstructure and the heat affected zone has been studied. The parameters have been modified in order to achieve low heat input and consequently low distortion as well as low metallurgical impact. Finally, an evaluation of the opportunities for an automatized repair process is made.
Due to significant developments over the last decades, laser beam welding has become a well-established industrial process offering high processing speeds and causing low component distortions. But an important issue currently preventing its intense use, especially in the energy or plant construction sector where high alloy steels are applied, concerns hot crack formation. Although considerable advances in understanding hot cracking mechanisms have been made, most of the known influencing factors are metallurgical in character. The thermo-mechanical effects are barely considered or quantified. Up to the present, there exist numerous hot cracking tests that were however conceived for welding methods other than laser beam welding. Considering the special features of the laser welding process, such as high cooling rates and the narrow process zone, results obtained with other welding techniques and test procedures cannot be transferred to laser beam welding. In this study, the laser beam weldability of various stainless steels was examined in terms of their susceptibility to hot cracking by means of the controlled tensile weldability test, which was proven to be suitable for use in conjunction with CO2 laser welding. This test allows the application of tensile strain at a variable fixed cross-head speed transverse to the welding direction. Full and partial penetration bead-on-plate welds were produced. In a first attempt to determine the impact of the applied external strain on the local transient strains and strain rates near the weld pool, an optical system was used to measure the backside surface of partial penetration welds. The results showed the influence of the strain and the strain rates on hot crack formation. Furthermore, a classification of the studied austenitic, duplex and ferritic stainless steels according to the established test criteria (critical strain and cross-head speed) was conducted.
Grain refinement is an important possibility to enhance the weldability of aluminium weld metal that is usually defined by its susceptibility to solidification cracking. In this study, grain refinement was achieved through the addition of commercial grain refiner containing titanium and boron to the GTA weld metal of aluminium alloy 6082. The weld metal mean grain size could be reduced significantly from about 70 µm to a saturated size of 21 µm with a change in grain shape from columnar to equiaxed. The grain refinement prevented the formation of centreline solidification cracking that was present only in welds with unrefined grain structure. A variation of torch speed led to a strong change of solidification parameters such as cooling rate that was measured in the weld metal and the corresponding solidification rate and thermal gradient. The ratio thermal gradient/growth rate (G/R) decreased from 50 K s/mm² (high torch speed) to 10 K s/mm² (low torch speed). However, the variation of torch speed did not change the tendency for solidification cracking. The microstructure of unrefined and completely refined weld metal was compared. The observed change in size and distribution of the interdendritic phases was related to the change in susceptibility to solidification cracking.
A multi-physics numerical model was developed to investigate the influence of a steady magnetic field during partial penetration keyhole laser beam welding of an aluminum plate in flat position. Three-dimensional heat transfer, fluid dynamics including phase transition and electromagnetic field partial differential equations were solved with the finite element differential equation solver COMSOL Multiphysics. The magnetic field was aligned perpendicularly to the welding direction. The main objective of these simulations was to estimate the critical value of the magnetic field needed to suppress convective flows in the weld pool during high-power (up to 20 kW) laser beam welding of aluminum alloys with up to 20 mm deep weld pool. It reveals that steady magnetic fields with corresponding Hartmann numbers Ha^2 ~ 10^4 based on the half-width of the weld pool can effectively suppress convective flows in the weld pool. Moreover, the typically occurring wineglass-shape of the weld cross section caused by thermo-capillary flow is weakened.
Simulation of an inductive weld pool support for deep penetration laser beam welding of metal parts
(2012)
three-dimensional laminar steady state numerical model was used to investigate the influence of an altemating current (ac) magnetic field during single pass high power laser beam keyhole welding of 20 mm thick aluminum. The three-dimensional heat transfer, fluid dynamics and electromagnetic field equations were solved with the commercial finite element package COMSOL Multiphysics. Dominant physical effects of the process were taken into account: Thermo-capillary (Marangoni) convection at the upper and lower weld pool surfaces, natural convection due to the gravity influence and the latent heat of solid-liquid phase transition. Simulations were conducted for several magnetic field strengths and it was found that the gravity drop-out associated with welding of thick plates due to the hydrostatie pressure can be prevented by the application of an ac magnetic field below the weld specimen of around 70 mT (rms) at an oscillation frequency of 450 Hz. The inductive support System allows for single-pass laser beam welding of thick aluminum plates. The flow pattem in the molten zone and the temperature distributions are significantly changed by the application of the electromagnetic forces in the weld pool.
The main characteristic feature of deep penetration laser beam welding is a large temperature difference between the plasma cavity (keyhole) in the centre of the weld pool and the melting/solidification front. Large temperature gradients in the weld pool result in a very intensive thermocapillary (Marangoni) convection. The weld pool surface width becomes very large and unstable. However, an externally applied oscillating magnetic field can stabilize the surface of the melt (the Garnier-Moreau effect, 1983). In the present work this technology was used to stabilize the surface of the weld pool in partial penetration 4.4 kW Nd:YAG laser beam welding of AW-5754 alloyin PA position. The AC magnet was mounted on the laser welding head. The oscillating magnet field was oriented perpendicular to the welding direction. It was found that the AC magnet field can drastically reduce the surface roughness of welds. The analysis of the x-ray images shows a rastic reduction of porosity content in the welds. This effect can be explained as a result of electromagnetic ectification of the melt.
Die lokalen Festigkeiten im Bereich einer Schweißverbindung sind maßgebend für deren Widerstandsfähigkeit gegenüber mechanischen Beanspruchungen. Im Gegensatz zu anderen präparationsaufwendigen Methoden, z. B. die Untersuchung von Mikro-Zugproben, liefert die instrumentierte Eindringprüfung mit deutlich geringerem Aufwand Verläufe von Festigkeiten mit sehr guter Ortsauflösung. Im Rahmen dieser Arbeit werden wahre Spannungs-Dehnungskurven aus zyklischen Eindringversuchen mittels Auswertungen auf der Basis repräsentativer Spannungen und Dehnungen und auf der Basis neuronaler Netze an Punktschweißverbindungen aus hochfesten Stählen, jeweils im Bereich des Grundwerkstoffs und der Schweißlinse, bestimmt. Die Ergebnisse werden exemplarisch für einen Stahltyp mit Ergebnissen von Zugversuchen am Grundwerkstoff und am thermisch behandelten Werkstoff mit Schweißgut ähnlicher Struktur verglichen und diskutiert.