Filtern
Erscheinungsjahr
- 2016 (8) (entfernen)
Dokumenttyp
- Beitrag zu einem Tagungsband (8) (entfernen)
Sprache
- Englisch (8)
Schlagworte
- Radioactive material (3)
- Spent fuel assessment (2)
- Transport packages (2)
- Approved packages (1)
- Design of the packaging attachment points (1)
- Experience feedback list (1)
- Fallprüfung (1)
- Finite element methods (1)
- Fire test (1)
- Gap analysis (1)
This paper presents data obtained from experiments performed using a bending test set-up developed at the Joint Research Centre (JRC) – Karlsruhe, for spent fuel segment testing. Adjustable sample holders, loading modes and other experimental conditions can be im- plemented in the experiments to study the effects of different deformation ranges up to cladding failure. The experimental set-up has been adapted to hot cell remote controlling and has a modular configuration, which allows manual and motor-driven loading option. The device has been calibrated on hydrogenated, unirradiated cladding tube segments filled with alumina pellets. The final application of present set-up is to test non-defueled spent fuel rod segments, pressurized to the original spent fuel rod pressure level. The range of applicability of this device, the scope of the experimental program and the first results from actual bending tests will be discussed.
Transport packages for spent nuclear fuel have to be assessed with respect to specific transport conditions which are defined in the regulations of the International Atomic Energy Agency. The physical state of the spent fuel and the fuel rod cladding as well as the geometric configuration of the fuel assemblies are important inputs for the evaluation of the package capabilities under these conditions. Cracks or failures in the fuel rod cladding can cause the release of gas, volatiles or fuel particles into the cavity. The amount of substances in the cavity has to be considered in the assessment of the activity release and criticality safety.
The mechanical analysis of the compound system formed by the fuel rod cladding and the spent fuel pellets is very difficult due to the limited knowledge of the material properties and the insufficient understanding of the interaction between pellets and cladding and between adjacent pellets. The variation of fuel assembly properties regarding cladding material, burn-up and the history of usage makes reliable predictions of the fuel rod behavior even harder.
For a better understanding about the behavior of spent fuel rods, JRC-ITU and BAM have started a joint research project. In this context, JRC-ITU has developed a test device which allows quasi-static 3-point-bending test on fuel rod segments in the hot cell. The loads are applied with respect to the boundary conditions of the activity release assessment. This paper deals with the numerical calculation of a single fuel rod segment under bending load. The aim is to identify the governing mechanical parameters by the variation of constitutive assumptions, contact conditions, inner constraints, etc. This knowledge helps for the interpretation of the experimental results. Furthermore, the improved understanding about the behavior of the cladding-pellets system will be beneficial for the assessment of spent fuel transport conditions.
For stowage and retention during transport, the International Atomic EnergyAgency (IAEA) Transport regulations (SSR-6) only require that the package shall be securely stowed. Additional information is given in the IAEA guidance material (SSG-26), that includes specific load factors that should be considered in the safety demonstrations.
Nevertheless, applicants commonly use other load factors to justify the design of the packaging attachment points. In particular, acceleration values vary between different countries and this may lead to difficulties during the validation of foreign approval certificates.
Discussions with applicants identified that the load factors presented in the IAEA guidance material are not necessarily relevant for the different transport modes. For some modes, the load factors are representative of situations occurring in routine conditions of transport. For other modes, the load factors are more representative of situations occurring in normal or accident conditions of transport.
Furthermore, the origins of the specified values are not clear. In this context, some IAEA TRANSSC members decided to review the stowage guidance. An international working group was constituted in 2013, including representatives of competent authorities, technical support organizations, and transport stakeholders. Several topics were discussed
and many questions were raised during the two year review. For example, some discussions focused on Paper No.1031 2 the conditions which have to be considered for stowage design, both as relevant to the load factors used for strength and fatigue analysis, as well as the criteria which have to be considered for the package attachment points. In addition, related questions on operational aspects were also discussed. Overall, the working group concluded that new guidance material was warranted as input into SSG-26.
As a result of those discussions, the international working group produced new guidance material for stowage in transport, addressing each of these topics. The proposal to modify the IAEA guidance material (SSG-26, Appendix IV), presented by France to the TRANSSC in the 2015 initiated Review cycle of the Regulations, was unanimously accepted and will be implemented in the next edition of the guidance material.
Packages for intermediate level waste (ILW) often contain residual water besides the actual waste. The water either exists as obvious free water or it may be bound physically or chemically, e.g. as pore water. A water driven gas generation could occur by vaporisation and by radiolysis. Steam as the result of vaporisation causes an increasing pressure inside a package and can affect corrosion. Vaporisation and condensation processes itself change the thermal behavior of the content especially during strongly unsteady thermal situations like accident fire situations. Radiolysis changes the chemical composition of the content which could cause an unexpected interaction, e.g. hydrogen embrittlement. Besides the pressure build-up the radiolysis of water generates hydrogen and oxygen, which can be highly flammable respectively explosive. The gas generation caused by vaporisation and radiolysis must be taken into account during the design and the safety assessment of a package. Pressure build-up, a changed thermal behavior and content chemistry, and especially the risk of accumulation of combustible gases exceeding the limiting concentration for flammability has to be considered in the safety assessment. Approaches to ensure the transportability of stored packages due to radiolysis will be discussed.
Packages for the transport of radioactive material are often equipped with impact limiters consisting of wood, encapsulated by steel sheets. These impact limiters shall ensure the transport cask meets the mechanical and thermal IAEA regulatory test requirements. After damage caused by the mechanical tests the package has to withstand a severe fire scenario. According to the regulations during and following the thermal test, the specimen shall not be artificially cooled and any combustion of materials of the package shall be permitted to proceed naturally.
Corresponding to results of the French institute IRSN combustion and smouldering of wood inside the impact limiter occurred during and after the fire test. An additional energy supply from a pre-damaged impact limiter to the cask could be the consequence for the safety assessment of the containment.
BAM started a first test phase to examine the issue of combustion for such kind of package components. The goal was to understand the phenomena under the consideration of relevant regulatory boundary conditions. Several metal buckets were filled with wood and equipped with thermocouples. The test specimens have been prepared with different damage arrangements to take the influence of the mechanical tests into account. This paper shows the experimental setup and the conduction of the tests. The first test shows that pre-damaged metal encapsulations can lead to smouldering of the wood and with this to a supplement energy release after the end of the 30 minute fire. BAM is in the preparation process for a second test phase. A thermal test will take place with a wood filled test specimen weighing about 2Mg.
BAM as competent authority regarding assessment of mechanical and thermal design, activity release and quality assurance aspects of SNF and HLW transport packages developed a thesaurus of experience feedback topics from recent approval procedures. The list is structured according to the European PDSR guide. It involves issues, which from BAM point of view, needed clarification during last package design assessment procedures. The list contains issues from operation (e.g. deactivation of handling lugs not intended for package handling), maintenance (e.g. leak tightness of impact limiting devices) to technical assessment (e.g. formation of hydrogen by radiolysis and its impact on pressure and ignitability, consideration of ageing mechanisms, thermo-mechanical assessment, impact of gaps between content and flask, spent fuel behaviour) as well as to general and specific safety analysis report requirements (e.g. report structure and required data).
Storage of spent nuclear fuel and high-level waste in dual purpose casks (DPC) is related with the challenge of maintaining safety for transportation over several decades of storage. Beside consideration of aging mechanisms by appropriate design, material selection and operational controls to assure technical reliability by aging management measures, an essential issue is the continuous control and update of the DPC safety case. Not only the technical objects are subject of aging but also the safety demonstration basis is subject of “aging” due to possible changes of regulations, standards and scientific/technical knowledge. The basic document, defining the transport safety conditions, is the package design safety report (PDSR) for the transport version of the DPC. To ensure a safe transport in future to a destination which is not known yet (because of not yet existing repository sites) periodical reviews of the PDSR, in connection with periodic renewals of package design approval certificates, have to be carried out. The main reviewing tool is a gap analysis. A gap analysis for a PDSR is the assessment of the state of technical knowledge, standards and regulations regarding safety functions of structures, systems and components.
Type B(U) packages for the transport of radioactive material have to withstand accident conditions of transport defined in the regulations of the IAEA International Atomic Energy Agency in form of different mechanical (drop) tests with a subsequent thermal test. According to the regulatory requirements the orientation of the package in drop tests shall be such to cause the most damaged state in the components performing the safety functions.
For the package lid system a 9-m drop onto the unyielding target with lid side downwards is often the most damaging orientation. The impact loads acting on the lid in this orientation result mainly from interaction between lid and internal content. In case of a movable content its impact onto the inner side of the lid can cause additional load peaks on the lid and the lid bolts. The intensity of the internal collision depends on the position of content relating to lid at the time of package first contact with target. Due to physical limitations an axial gap, which could be set in “pre-drop” configuration of package or which could spontaneously appear during the drop test, usually does not cover the maximum size possible in specific package design. In this context, the combination of drop tests with post-test analysis can be helpful to better estimate the effect of internal impact.
The paper summarized some aspects of this issue based on the BAM experience in the design assessment of Type B(U) transport packages. Additionally the paper shall support applicants in German approval procedures to reduce rounds of questions and ensure delivery of reliable safety case documents to the authorities. International discussions of this issue at the IAEA and a joint proposal by France and Germany to improve Advisory Material text will be introduced.