Filtern
Dokumenttyp
- Beitrag zu einem Tagungsband (2)
- Zeitschriftenartikel (1)
- Vortrag (1)
Sprache
- Englisch (4)
Schlagworte
- Diameter (4) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (1)
Innovative seismic and resistivity tools for determining the diameter of jet grouting columns
(2016)
Jet grouting is used for soil improvement, foundation support and groundwater low control all over the world. It is well accepted and subject of standardization in many countries. However, some issues with the method remain. As the grout columns are produced in the subsurface without visual control in an often inhomogeneous soil, the prediction of the column’s diameter is still a challenge. All methods applied so far have their limitations.
The approach presented in this study is twofold. At Colorado School of Mines a resistivity probe has been developed, which is pushed into the fresh grout directly after production. ERT sections are measured and inverted. Given some background information is available, the diameter of the columns can be evaluated.
At BAM the focus has been on post-production investigations using seismic borehole methods. After hardening of the concrete seismic waves are sent through the column downhole (sensors placed in a casing in the column’s axis, source on top) and crosshole (source and sensor in boreholes on opposite sides of the column). We have developed a scheme to evaluate the diameter of the column based on travel time measurements without calibration. As this method is eventually more time and cost intensive we assume its application mainly for test columns. These are casted and dug out for visual inspection to determine appropriate grouting parameters. Our method would replace the often very cost intensive visual inspection.
Both approaches have been tested at three test columns produced at BAM’s test site at Horstwalde, Germany and on an actual constructions site. Both methods have been in good agreement with the diameters predicted by the jet grouting contractors, which were confirmed in one case by mechanical measurements.
Jet grouting is a geotechnical method of ground improvement to increase shear strength and stiffness of soils. The method is typically used to construct in-situ geometries of grouted soil such as panels or columns. The diameter of grouted columns and its material strength depend on various process parameters and the subsurface soil properties. It is only vaguely possible to predict the final column diameter. Therefore, it is a general practice to excavate a test column and perform a visual examination. However, an excavation to control the in situ diameter is often impossible, especially under complex site conditions, such as a high ground water table. Therefore, as part of a research project, borehole seismic measurements (crosshole, downhole and tomography) were tested as a quality control to verify the extent of the column and to monitor the influence of the jet grout injection on the soil over time. The field surveys were conducted before and after the jet grouting process at different time intervals. The acquired seismic data show clear traveltime differences which allow the determination of the specific column depth and diameter. The tomogram measured in the natural soil and the tomograms of the measurements after the injection process were used to visualize the time dependent effects of the jet grout injection on the soil.
A systematic study of the luminescence properties of monodisperse β-NaYF4: 20% Yb3+, 2% Er3+ upconversion nanoparticles (UCNPs) with sizes ranging from 12–43 nm is presented utilizing steady-state and time-resolved fluorometry.
Special emphasis was dedicated to the absolute quantification of size- and environment-induced quenching of upconversion luminescence (UCL) by highenergy O–H and C–H vibrations from solvent and ligand molecules at different excitation power densities (P). In this context, the still-debated Population pathways of the 4F9/2 energy level of Er3+ were examined. Our results highlight the potential of particle size and P value for color tuning based on the pronounced near-infrared emission of 12 nm UCNPs, which outweighs the red Er3+ emission under “strongly quenched” conditions and accounts for over 50% of total UCL in water. Because current rate equation models do not include such emissions, the suitability of these models for accurately simulating all (de)population pathways of small UCNPs must be critically assessed. Furthermore, we postulate population pathways for the 4F9/2 energy level of Er3+, which correlate with the size-, environment-, and P-dependent quenching states of the higher Er3+ energy levels.
Sealing and strengthening of the subsoil by injection is a major issue in the field of geotechnical engineering. This involves also jet grouting, which allows creating columns of grouted soil by eroding and mixing the in-situ soil with a thin cement suspension. A general difficulty of this method is to predict the column diameter and its material strength. Here, we present two-dimensional finite-difference numerical simulation results of a promising non-destructive quality assurance testing tool to evaluate the diameter of jet grout columns. This approach incorporates crosshole and downhole seismic measurements. Preliminary tests showed that this tool is applicable under real site conditions.