Filtern
Erscheinungsjahr
Dokumenttyp
- Zeitschriftenartikel (18)
- Beitrag zu einem Tagungsband (13)
- Beitrag zu einem Sammelband (4)
- Vortrag (2)
- Dissertation (1)
Sprache
- Englisch (23)
- Deutsch (12)
- Französisch (3)
Schlagworte
- DLC (38) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (2)
Tribological screening tests (simple, reciprocating ball-on-flat tests) were performed with the objective to identify an appropriate coating for the articulating surfaces of artificial hip joints whose acetabular cups and femoral stems are made from Ti6Al4V alloy, which is appreciated for its light weight, good biocompatibility and elastic properties similar to those of natural bone. Standard coatings like TiN or CrN performed better than more complicated multi-layer systems, though not as good as different types of amorphous carbon coatings, generally referred to as diamond-like carbon or DLC coatings. Among the latter, hydrogenated amorphous carbon (a-C:H) displayed the best properties, especially if the hydrogen content was increased by reducing the bias voltage during PA-CVD-deposition.
The optimised a-C:H coating revealed the most promising wear behaviour under the applied testing conditions, i.e. the increase of linear wear with the number of cycles was close to zero. Regarding the materials examined in this study, correlation of wear with mechanical properties obtained by nano-indentation revealed that high hardness was not an adequate criterion for selecting appropriate coatings. A high ratio of hardness and elastic modulus (H/E) proved to be more important. Microstructural and micro-analytical investigations revealed transformation of TiN and CrN to TiO2 and Cr2O3, respectively, and amorphous carbon was, at least partly, transformed to graphite. Furthermore, incorporation of Al2O3 from the ball was observed at a very fine scale. The wear debris of favourable coatings always formed agglomerates of nano-scale particles. It was shown that commercial nano-particles of Al2O3, Cr2O3 and carbon black are comparable to particles generated by the tribological tests. However, it is uncertain whether they are comparable to those formed during simulator studies or in vivo. Furthermore, the performance of the favourable coating has to be tested in a hip joint simulator before its potential for application in prostheses can be assessed.
Zirkonium-basierte Dünnschichten in hochbeanspruchten Wälzkontakten als Alternative zu DLC und ta-C
(2009)
Wälzbeständigkeit von ta-C Dünnschichten unter hohen Hertzschen Beanspruchungen bis zu 3000 MPa
(2010)
Original equipment manufacturers (OEMs) and end-users perceive 'Zero Wear' differently. The 'Zero Wear' approach will be put into a general relation for different applications and illuminated by individual paths, either based on monolithic materials, thin film coatings or alternative base oils, featuring triboactive materials and lubricious oxides for tribological engine components and dry running foil bearings or specific DLC, ta-C and novel Zirconium-based thin film coatings for concentrated contacts above FZG 14 and alternative engine oils (NoSAP & bio-no-tox). The associated tribometric test equipments for these examples will also be detailed.
Some of the properties intrinsically present in the backbone of polyalkylene glycols (PAGs), which have nowadays attracted the automotive original equipment manufacturers (OEMs), are presented, such as bio-no-tox properties, heat capacity, extended drains, low friction, low AlSi-liner wear, fuel economy, and very high viscosity indices, and are achieved with metal-, ash-, and polymer-free formulations, which guarantee no adverse contamination of the lambda sensor and the active centers of the catalyzer as well as not to increase the exhaust back pressure of the particulate filter through ash deposits. This paper illuminates the latest results from OEM's engine bench and road testing supporting the following functional benefits: (a) bio-no-tox, (b) improvements of fuel economy, even when compared with latest hydrocarbon-based prototype oils, (c) reduced wear, (d) reduced engine friction, (e) extended drains, (f) suited for bio-fuels, (g) no adverse effects on after-treatment devices through ash-, metal-, and polymer-free formulations, etc.