Filtern
Dokumenttyp
- Beitrag zu einem Tagungsband (2)
- Zeitschriftenartikel (1)
- Vortrag (1)
Sprache
- Englisch (4)
Referierte Publikation
- nein (4)
Schlagworte
- Cyclic load (4) (entfernen)
Organisationseinheit der BAM
Eingeladener Vortrag
- nein (1)
Whenever geosynthetics are used to reinforce or stabilise infrastructural elements such as road- and railways, bridge abutments, run- and taxiways on airports or to protect coastlines of canals and other steep slopes they may be exposed to cyclic loads. Therefore, a reduction factor for dynamic effects on the geosynthetic tensile strength has been included into the calculation of the Long Term Design Strength (LTDS). An approach to assess the behaviour of geosynthetics is to adopt Woehler- or Smith graphs and Haigh-diagrams for polymers. This is because an endurance limit for polymers, which defines an infinite life under a defined cyclic load, has not been seen so far. A huge amount of mechanical testing is needed to predict the behaviour of geosynthetics against this particular background.
To reduce these efforts while getting an indication of the cyclic effect on geosynthetics, a combined method of mechanical and chemical analysis has been developed. The pure tensile strength tests to determine the residual strength after cyclic stress has been amended by IR-spectroscopy and Differential Scanning Calorimetry (DSC). In this context the chain change model of PET has been proven as valid for cyclic loads as well, which helps to define the endurance limit of materials made out of PET. For polyolefins such as PP and PE, a limit for the maximum alternating load has been identified at the point of the stress strain graph where the actual and the numerical stress of a material diverge from each other. Cyclic tensile strength tests have been carried out in a hydraulic test frame. The test parameters have been set to simulate the service life of a railway bed trafficked by high speed trains (ICE).
Casks for the transport and storage of heat generating radioactive waste in Germany are normally provided with screwed lid systems, which are in most cases equipped with double jacket metal seals with an inner spring wire to provide long term resistance to the seal compression force. Preservation of the high sealing quality of those seals under operational and accidental stress conditions is essentially important to the safety of those casks. Relative displacements of the lid system surfaces caused by specific impact scenarios cannot be excluded and have to be evaluated with respect to a possible increase in the leakage rate.
To get representative data for such metal sealed lid systems, BAM has developed a special conceptualised flange system placed in an appropriate testing machine for relevant mechanical loading of the metal seals under static and cyclic conditions. Furthermore, the flange system enables continuous measurement of the standard helium leakage rate during each test.
The primary aim of the investigation is to identify the correlation between variation of installation conditions (axial displacements) caused by external loads and the standard helium leakage rate. An essential parameter in this case is the useable resilience ru of a metal seal under relevant stress conditions. The useable resilience ru is the vertical difference in the cross-section between the seal's assembling status and the point where the leakage rate, by means of external load relieving, exceeds the quality criterion of 10-8 Pa m3 s-1. Load relieving can instantly occur due to modification of the seal groove dimension caused by accident impacts and deformation of the lid system. Furthermore, component specific basis data for the development of finite element calculation models should be collected. In the tests, seals are subjected to static and cyclic loads. All tests are performed at ambient temperature.
This paper presents the test configuration, different test series and results of the current experiments. Typical load-displacement-leakage rate correlations are presented and discussed.
Global energy consumption will increase in the future necessitating both fossil fuels and renewable energy choices - especially wind energy. Such high energy demand requires installation of offshore energy structures, rigs, platforms and towers, which are susceptible to adverse environmental conditions along with maintenances. Due to their large size and remote locations, cylindrical grouted joints are often adopted between substructure and foundation in these offshore platforms and wind structures such as monopiles. However, these connections are composite structures with exterior sleeve, interior pile and infill mortar. Degradation and settlements were reported inside similar connections, which were installed in last three decades. Besides, grouting in the offshore sites were proven difficult to obtain ideal load bearing capacity. In-situ loading conditions were also found to be affecting the failure mechanism inside such connections. This study aims at characterizing the nature of cracks generated in these grouted connections under both static and cyclic loading. Scaled grouted joints were manufactured using a novel reusable mold, and connections were loaded to failure to visualize the main failure patterns. An assessment between failure under these two types of load is drawn along with comparison to previously available literature.
Global energy consumption will increase in the future necessitating both fossil fuels and renewable energy choices - especially wind energy. Such high energy demand requires installation of offshore energy structures, rigs, platforms and towers, which are susceptible to adverse environmental conditions along with maintenances. Due to their large size and remote locations, cylindrical grouted joints are often adopted between substructure and foundation in these offshore platforms and wind structures such as monopiles. However, these connections are composite structures with exterior sleeve, interior pile and infill mortar. Degradation and settlements were reported inside similar connections, which were installed in last three decades. Besides, grouting in the offshore sites were proven difficult to obtain ideal load bearing capacity. In-situ loading conditions were also found to be affecting the failure mechanism inside such connections. This study aims at characterizing the nature of cracks generated in these grouted connections under both static and cyclic loading. Scaled grouted joints were manufactured using a novel reusable mold, and connections were loaded to failure to visualize the main failure patterns. An assessment between failure under these two types of load is drawn along with comparison to previously available literature.