FG Werkzeugmaschinen
Refine
Year of publication
Document Type
Way of publication
- Open Access (5)
Language
- German (65)
- English (18)
- Russian (3)
- Chinesisch (1)
- Polnisch (1)
Keywords
- Energieeffizienz (12)
- Tragrolle (11)
- Tragrollenprüfstand (5)
- Gurtförderanlage (4)
- Lärm (4)
- strukturierte Bleche (4)
- Leichtbau (3)
- Wasserstrahlschneiden (3)
- energy efficiency (3)
- spanende Bearbeitung (3)
Institute
The article tells about the research on wear and tear of mud pump liners, namely: main characteristics that distinguish ceramic liner from the other ones used on the units equipped with the hydraulic system for washing out the drilling wells from cuttings, design of ceramic liners, calculation of the wear rate of ceramic liners, and the positive contribution they made on the modern drilling process. Besides, the research is made on the simplicity of the structure of ceramic liners, a short amount of time consumed to assemble and replace the liners, safety of the work, cost-effectiveness, wearing and corrosion durability, and also compliance with other requirements.
Design of an energy-autonomous sensor with wireless data data transmission for use on rollers
(2023)
Mechanically moving parts such as rollers in belt conveyor systems are subject to wear and tear that limits their service life. Damage causes loss of production as well as damage to the entire production plant. A system design is presented with which it is possible to record and wirelessly transmit relevant measured values in or on rollers without an additional voltage source. The system should work largely maintenance-free and be realisable with components currently freely available on the market.
Die Erfassung der Eigenschaften von Tragrollen und Fördersystemen ist nicht nur im Rahmen der Fertigung und Qualitätssicherung erforderlich, sondern insbesondere auch nach Inbetriebnahme und während der gesamten Laufzeit der Förderanlage. Im Regelfall erfolgt kurz nach der Erstinbetriebnahme die Abnahmekontrolle durch den Hersteller oder Anlagenbetreiber, indem die im Pflichtenheft aufgeführten Parameter überprüft werden.
Bei Inbetriebnahme:
- grundsätzliche Funktionskontrolle mit und ohne Fördergut
- Anlaufverhalten
- Kontrolle auf Gurtschieflauf
- Ausrichtung der Gerüstfelder und Tragrollengirlanden
- akustische Abnahme für immissionsrelevante Anlagen
- zusätzlich Gurtspannung, Kontrolle der Getriebe, Antriebe und Gurttrommeln hinsichtlich elektrischer Parameter, Schlupf usw.
Im Zuge des Betriebs tritt kontinuierlicher Verschleiß, insbesondere im Bereich der Tragrollen auf. Um ungeplante Stillstände und Störungen zu vermeiden, werden verschiedene Kontrollen und Instandhaltungsmaßnahmen durchgeführt (Lars Sternitzke, LEAG, 2021):
- regelmäßige Kontrollfahrten durch z.B. mobilen Löschtrupp, Überprüfung auf grobe optische und akustische Auffälligkeiten
- automatische Wärmebildkameras zur Detektion von Heißläufern, insbesondere bei brandgefährdeten Anlagen (Kohle)
- jährliche Schallmessungen bei immissionsrelevanten Anlagen
The article tells about the research on wear and tear of mud pump liners, namely: main characteristics that distinguish ceramic liners from others used on the units equipped with a hydraulic system
for washing out the drilling wells from cuttings, design of ceramic liners, calculation of the wear rate of ceramic liners, and the positive contribution they have made on the modern drilling process. Besides, the research is made on the simplicity of the structure of ceramic liners, little time required to assemble and replace the liners, safety of the work, cost-effectiveness, wearing and corrosion durability, and also compliance with other requirements.
Выбор материала и геометрических параметров расточного резца для обработки покрытий на основе никеля
(2023)
Разработка технологии механической обработки восстанавливаемых в ремонтном производстве деталей, включающая в себя выбор способа и режимов их обработки, режущего инструмента и др., является сложной задачей, решение которой определяет качество восстанавливаемых изделий. Качество механической обработки во многом зависит от обрабатываемости металла, под которой понимают способность материала подвергаться резанию. Рассмотрены особенности механической обработки втулок по- сле восстановления изношенной внутренней поверхности, состоящей из черного, чи- стового и тонкого растачивания, а также операции хонингования. При механической обработке восстанавливаемых втулок наибольшую трудность представляют операции чернового и чистового растачивания, так как после индукционного напекания с по- следующим раскатыванием твердость получаемых слоев находится в пределах HRC 48…55, что усложняет работу резцов при растачивании втулок. Для наплавки на де- тали, работающие в условиях изнашивания (коррозионного, эрозионного и термиче- ского), применяют порошок ПГ-СР2, имеющий систему легирования Ni–Cr–B–Si. Значительную волнистость и шероховатость поверхности, возникающую в результате наплавки, устраняют накатыванием. Одним из важных вопросов при обработке по- крытий, нанесенных центробежным индукционным напеканием с последующим рас- катыванием, является выбор материала и геометрических параметров режущего ин- струмента для чернового и чистового растачивания. При правильном выборе матери- ала и геометрических параметров расточного резца можно значительно уменьшить износ режущего инструмента, что позволит увеличить его стойкость и производи- тельность обработки, а следовательно, снизить себестоимость изготовления детали. Исследовано влияние технологических параметров на износ и геометрических пара- метров на стойкость режущего инструмента с целью оптимизации условий растачи- вания восстановленных цилиндров судовых двигателей.
Методика определения теплового состояния втулки цилиндра при центрoбежном индукционном напекании
(2022)
Распределение температуры во втулке цилиндра судового двигателя при ее нагреве и охлаждении — один из важнейших факторов, под действием которых формируются структура и свойства покрытий в процессе восстановления цилиндра методом центро- бежного индукционного напекания. Проведены экспериментальные исследования, позволившие получить графики распределения температуры по диаметрам втулки ци- линдра судового двигателя при ее нагреве и охлаждении. Установлено, что на процесс напекания порошковых материалов существенно влияют теплофизические свойства втулки. Изменяя скорость нагрева, можно получать покрытия при различных значени- ях температуры и времени напекания. Выполнено моделирование распределения тем- пературы в стенке втулки цилиндра при центробежном индукционном напекании в за- висимости от времени напекания, а также с учетом геометрических параметров втулки, теплоотдачи, теплопроводности, материала втулки, температуры внешней среды и т. д. Получены выражения для определения распределения температуры в стенке втулки цилиндра при центробежном индукционном напекании. Задавая значения параметров центробежного индукционного напекания, по полученным формулам можно смодели- ровать и заранее получить распределение температуры в стенке втулки цилиндра. Для визуального отображения изменения температурного поля во втулке при центробеж- ном индукционном напекании выполнено моделирование в среде Autodesk Fusion 360.
機械設計實戰—從零件、裝配到創新設計
(2023)
Innerhalb dieser Arbeit werden Ansätze zur elektrotechnischen Funktionalisierung von industriellen Rohrleitungsdichtungen theoretisch und praktisch analysiert. Das Fernziel ist es hierbei, Neu- und Bestandsanlagen mittels vollständig eingebetteter, multimaterial 3D-gedruckter, messtechnisch neu gedachter Dichtungen nahtlos in moderne Automatisierungssysteme zu integrieren, um eine verbesserte Ressourcennutzung zu erreichen. Im Folgenden sind zunächst die grund-legenden Schritte „Aufbau eines Laborprüfstandes“, „Simulation geeignet scheinender Messmethoden“ und „Studie leitfähig druck- und kontaktierfähiger Strukturen“ als Teil der Forschungsaktivitäten hierzu dargestellt.
The main purpose of the article is to increase productivitiy, reduce processing time and the same time increase the cutting speed. The results are also displayed in Excel using a number of cutting parameters. For this purpose, the article shows the results of both high-speed milling and high-speed turning of a machine with different types of tools, as well as processing of one tool on different types of machines. Unlike other machines, in general, the work on the machines of universal processing centers turned out to be more productive. The feed rate of the machine tools is the focus area here. If we increase cutting values, then the tool life is reduced and that leads to higher tool costs. With universal high-performance machines we cannot save costs for tools (we can only save machine tool costs). Compared to universal high-performance machines, we can save tool costs with Universal Machining Center. Therefore, it is suggested to the machining with the universal machining center, although the machining time and cutting time is faster with the universal high-performance machine.