Refine
Document Type
- Article (5)
- conference proceeding (article) (1)
- conference proceeding (presentation) (1)
- Other (1)
- Report (1)
Publication reviewed
- begutachtet (6)
- nicht begutachtet (3)
Keywords
- LiDAR sensor (2)
- highly automated driving (2)
- open simulation interface (2)
- ASTM E3125-17 standard (1)
- Fahrerassistenzsystem (1)
- LiDAR sensor; rain; fog; sunlight; advanced driver-assistance system; backscattering; Mie theory; open simulation interface; functional mock-up interface; functional mock-up unit (1)
- Simulation (1)
- advanced driver assistance systems (1)
- advanced driver-assistance system (1)
- automotive LiDAR sensor (1)
- deep learning (1)
- false negative (1)
- false positive (1)
- functional mock-up interface (1)
- functional mock-up unit (1)
- micro-electro-mechanical systems (1)
- motion distortion (1)
- motion distortion effect (1)
- point cloud (1)
- point cloud distortion (1)
- simulation-based testing (1)
- velocity estimation (1)
Automated vehicles use light detection and ranging (LiDAR) sensors for environmental scanning. However, the relative motion between the scanning LiDAR sensor and objects leads to a distortion of the point cloud. This phenomenon is known as the motion distortion effect, significantly degrading the sensor’s object detection capabilities and generating false negative or false positive errors. In this work, we have introduced ray tracing-based deterministic and analytical approaches to model the motion distortion effect on the scanning LiDAR sensor’s performance for simulation-based testing. In addition, we have performed dynamic test drives at a proving ground to compare real LiDAR data with the motion distortion effect simulation data. The real-world scenarios, the environmental conditions, the digital twin of the scenery, and the object of interest (OOI) are replicated in the virtual environment of commercial software to obtain the synthetic LiDAR data. The real and the virtual test drives are compared frame by frame to validate the motion distortion effect modeling. The mean absolute percentage error (MAPE), the occupied cell ratio (OCR), and the Barons cross-correlation coefficient (BCC) are used to quantify the correlation between the virtual and the real LiDAR point cloud data. The results show that the deterministic approach matches the real measurements better than the analytical approach for the scenarios in which the yaw rate of the ego vehicle changes rapidly.
This paper provides an approach for controlling the level of risk when operating highly automated transportation systems like cars, trains and similar. Such systems replace human perception and decision-making by employing highly sophisticated solutions based on electronics, IT, and AI. Such systems have demonstrated the potential for building highly automated vehicles, but, as of today, encounter challenges in correctly understanding the extremely complex open contexts, into which such vehicles could be deployed. Its key focus is on bounding the risks stemming from uncertainty in the perception of the environment.
Measurement performance evaluation of real and virtual automotive light detection and ranging (LiDAR) sensors is an active area of research. However, no commonly accepted automotive standards, metrics, or criteria exist to evaluate their measurement performance. ASTM International released the ASTM E3125-17 standard for the operational performance evaluation of 3D imaging systems commonly referred to as terrestrial laser scanners (TLS). This standard defines the specifications and static test procedures to evaluate the 3D imaging and point-to-point distance measurement performance of TLS. In this work, we have assessed the 3D imaging and point-to-point distance estimation performance of a commercial micro-electro-mechanical system (MEMS)-based automotive LiDAR sensor and its simulation model according to the test procedures defined in this standard. The static tests were performed in a laboratory environment. In addition, a subset of static tests was also performed at the proving ground in natural environmental conditions to determine the 3D imaging and point-to-point distance measurement performance of the real LiDAR sensor. In addition, real scenarios and environmental conditions were replicated in the virtual environment of a commercial software to verify the LiDAR model’s working performance. The evaluation results show that the LiDAR sensor and its simulation model under analysis pass all the tests specified in the ASTM E3125-17 standard. This standard helps to understand whether sensor measurement errors are due to internal or external influences. We have also shown that the 3D imaging and point-to-point distance estimation performance of LiDAR sensors significantly impacts the working performance of the object recognition algorithm. That is why this standard can be beneficial in validating automotive real and virtual LiDAR sensors, at least in the early stage of development. Furthermore, the simulation and real measurements show good agreement on the point cloud and object recognition levels.
A Methodology to Model the Rain and Fog Effect on the Performance of Automotive LiDAR Sensors
(2023)
In this work, we introduce a novel approach to model the rain and fog effect on the light detection and ranging (LiDAR) sensor performance for the simulation-based testing of LiDAR systems. The proposed methodology allows for the simulation of the rain and fog effect using the rigorous applications of the Mie scattering theory on the time domain for transient and point cloud levels for spatial analyses. The time domain analysis permits us to benchmark the virtual LiDAR signal attenuation and signal-to-noise ratio (SNR) caused by rain and fog droplets. In addition, the detection rate (DR), false detection rate (FDR), and distance error derror of the virtual LiDAR sensor due to rain and fog droplets are evaluated on the point cloud level. The mean absolute percentage error (MAPE) is used to quantify the simulation and real measurement results on the time domain and point cloud levels for the rain and fog droplets. The results of the simulation and real measurements match well on the time domain and point cloud levels if the simulated and real rain distributions are the same. The real and virtual LiDAR sensor performance degrades more under the influence of fog droplets than in rain.
This work introduces a process to develop a tool-independent, high-fidelity, ray tracing-based light detection and ranging (LiDAR) model. This virtual LiDAR sensor includes accurate modeling of the scan pattern and a complete signal processing toolchain of a LiDAR sensor. It is developed as a functional mock-up unit (FMU) by using the standardized open simulation interface (OSI) 3.0.2, and functional mock-up interface (FMI) 2.0. Subsequently, it was integrated into two commercial software virtual environment frameworks to demonstrate its exchangeability. Furthermore, the accuracy of the LiDAR sensor model is validated by comparing the simulation and real measurement data on the time domain and on the point cloud level. The validation results show that the mean absolute percentage error (MAPE) of simulated and measured time domain signal amplitude is 1.7%.
In addition, the MAPE of the number of points Npoints and mean intensity Imean values received from the virtual and real targets are 8.5% and 9.3%, respectively. To the author’s knowledge, these are the smallest errors reported for the number of received points Npoints and mean intensity Imean values up until now. Moreover, the distance error derror is below the range accuracy of the actual LiDAR sensor, which is 2 cm for this use case. In addition, the proving ground measurement results are compared with the state-of-the-art LiDAR model provided by commercial software and the proposed LiDAR model to measure the presented model fidelity. The results show that the complete signal processing steps and imperfections of real LiDAR sensors need to be considered in the virtual LiDAR to obtain simulation results close to the actual sensor. Such considerable imperfections are optical losses, inherent detector effects, effects generated by the electrical amplification, and noise produced by the sunlight.
Many modern automated vehicle sensor systems use light detection and ranging (LiDAR) sensors. The prevailing technology is scanning LiDAR, where a collimated laser beam illuminates objects sequentially point-by-point to capture 3D range data. In current systems, the point clouds from the LiDAR sensors are mainly used for object detection. To estimate the velocity of an object of interest (OoI) in the point cloud, the tracking of the object or sensor data fusion is needed. Scanning LiDAR sensors show the motion distortion effect, which occurs when objects have a relative velocity to the sensor. Often, this effect is filtered, by using sensor data fusion, to use an undistorted point cloud for object detection. In this study, we developed a method using an artificial neural network to estimate an object’s velocity and direction of motion in the sensor’s field of view (FoV) based on the motion distortion effect without any sensor data fusion. This network was trained and evaluated with a synthetic dataset featuring the motion distortion effect. With the method presented in this paper, one can estimate the velocity and direction of an OoI that moves independently from the sensor from a single point cloud using only one single sensor. The method achieves a root mean squared error (RMSE) of 0.1187 m s−1 and a two-sigma confidence interval of [−0.0008 m s−1, 0.0017 m s−1] for the axis-wise estimation of an object’s relative velocity, and an RMSE of 0.0815 m s−1 and a two-sigma confidence interval of [0.0138 m s−1, 0.0170 m s−1] for the estimation of the resultant velocity. The extracted velocity information (4D-LiDAR) is available for motion prediction and object tracking and can lead to more reliable velocity data due to more redundancy for sensor data fusion.
In this article, the optimization of the control circuit and path planning of a delta kinematic with the help of machine learning is presented. The described delta kinematic is primarily used for pick-and-place applications in the field of packaging machines. The optimization of the path planning procedure aims to make the workflow more efficent and flexible for commissioning the delta kinematic. By optimizing the control circuit using machine learning, mechanical oscillations and the deviation of the specified path are to be minimized. The possible use of a simulator for training, the prediction quality and the implementation on the robot controller are discussed. Furthermore, the path planning procedure was optimized. For this purpose, an environment was implemented in which a reinforcement learning agent plans the path of the robot between a starting point and a target point in a time-optimized manner, considering interference contours e.g. from the machine. The obtained results show the optimization of the robot by machine learning with a root mean squared error of the predicted torques of 0.06025 Nm in a prediction time of around 0.125 ms and the possibility of path planning with different criteria.
Light detection and ranging (LiDAR) sensors are increasingly applied to automated driving vehicles. Microelectromechanical systems are an established technology for making LiDAR sensors cost-effective and mechanically robust for automotive applications. These sensors scan their environment using a pulsed laser to record a point cloud. The scanning process leads in the point cloud to a distortion of objects with a relative velocity to the sensor. The consecutive generation and processing of points offers the opportunity to enrich the measured object data from the LiDAR sensors with velocity information by extracting information with the help of machine learning, without the need for object tracking. Turning it into a socalled 4D-LiDAR. This allows object detection, object tracking, and sensor data fusion based on LiDAR sensor data to be optimized. Moreover, this affects all overlying levels of autonomous driving functions or advanced driver assistance systems. However, since such sensor-specific effects are rarely available in public datasets and the velocities of target objects are not included as ground truth in these datasets, it makes sense to enrich the limited real-world data with synthetic data. Therefore, this paper discusses how such datasets can be created and combined to efficiently predict velocities on realworld data using the authors' novel method dubbed VeloPoints.