Refine
Year of publication
Document Type
Keywords
- (CPV) Approach for Engine Applications (1)
- 3D CFD Engine Knock (1)
- Advanced Predictive (1)
- Assessment of Water Injection (1)
- Combustion, Mechanism Reduction (1)
- Detailed Chemistry (1)
- Development of a Computationally Efficient Progress (1)
- Diesel Engine, Stochastic Reactor Modeling, Particlulate Matter (1)
- Efficient tracking of knock (1)
- Engine knock is an important phenomenon (1)
Institute
BTU
3D CFD Engine Knock Predication and Evaluation Based on Detailed Chemistry and Detonation Theory
(2017)
Advanced Predictive Diesel Combustion Simulation Using Turbulence Model and Stochastic Reactor Model
(2017)
Methanol is today considered a viable green fuel for combustion engines because of its low soot emissions and the possibility of it being produced in a CO2-neutral manner. Methanol as a fuel for combustion engines have attracted interest throughout history and much research was conducted during the oil crisis in the seventies. In the beginning of the eighties the oil prices began to decrease and interest in methanol declined. This paper presents the emission potential of methanol. T-Φ maps were constructed using a 0-D reactor with constant pressure, temperature and equivalence ratio to show the emission characteristics of methanol. These maps were compared with equivalent maps for diesel fuel. The maps were then complemented with engine simulations using a stochastic reactor model (SRM), which predicts end-gas emissions. The SRM was validated using experimental results from a truck engine running in Partially Premixed Combustion (PPC) mode at medium loads. The SRM was able to predict the combustion in terms of pressure trace and rate of heat release. The CO and NOx emissions were matched, however, the HC emissions were underestimated. Finally, the trajectories from the SRM simulations were superimposed on the T-Φ maps to investigate the in engine conditions. The T-Φ map analysis shows that emission of soot are non-existent, formaldehyde can be avoided and that emissions of methane are kept at, compared to diesel combustion, low levels, however CO and NOx levels are similar to diesel combustion. These results were confirmed for engine conditions by the SRM simulations and the engine experiments.
Several models for ignition, combustion and emission formation under diesel engine conditions for multi-dimensional computational fluid dynamics have been proposed in the past. It has been recognized that the use of a reasonably detailed chemistry model improves the combustion and emission prediction especially under low temperature and high exhaust gas recirculation conditions.The coupling of the combustion chemistry and the turbulent flow can be achieved with different assumptions. In this paper we investigate a selection of n-heptane spray experiments published by the Engine Combustion Network (ECN spray H) with three different combustion models: well-stirred reactor model, transient interactive flamelet model and progress variable based conditional moment closure. All models cater for the use of detailed chemistry, while the turbulence-chemistry interaction modeling and the ability to consider local effects differ.The same chemical mechanism is used by all combustion models, which allows a comparison of ignition delay, flame stabilization and flame lift-off length between the experiments and the results from simulations using the different combustion models. The investigated parameters influence the predictions of computational fluid dynamics simulations of diesel engines. This study indicates that the most reasonable behavior with respect to ignition, flame stabilization and flame structure is predicted by the progress variable based conditional moment closure model.
In this work a soot source term tabulation strategy for soot predictions under Diesel engine conditions within the zero-dimensional Direct Injection Stochastic Reactor Model (DI-SRM) framework is presented. The DI-SRM accounts for detailed chemistry, in-homogeneities in the combustion chamber and turbulence-chemistry interactions. The existing implementation [1] was extended with a framework facilitating the use of tabulated soot source terms. The implementation allows now for using soot source terms provided by an online chemistry calculation, and for the use of a pre-calculated flamelet soot source term library. Diesel engine calculations were performed using the same detailed kinetic soot model in both configurations. The chemical mechanism for n-heptane used in this work is taken from Zeuch et al. [2] and consists of 121 species and 973 reactions including PAH and thermal NO chemistry. The engine case presented in [1] is used also for this work. The case is a single-injection part-load passenger car Diesel engine with 27 % EGR fueled with regular Diesel fuel. The two different approaches are analyzed and a detailed comparison is presented for the different soot processes globally and in the mixture fraction space. The contribution of the work presented in this paper is that a method which allows for a direct comparison of soot source terms - calculated online or retrieved from a flamelet table - without any change in the simulation setup has been developed within the SRM framework. It is a unique tool for model development. Our analysis supports our previous conclusion [1] that flamelet soot source terms libraries can be used for multi-dimensional modeling of soot formation in Diesel engines.
A chemical species lumping approach for reduction
of large hydrocarbons and oxygenated fuels is presented. The methodology is based on an a priori analysis of the Gibbs free energy of the isomer species which is then used as main criteria for the evaluation of lumped group. Isomers with similar Gibbs free energy are lumped assuming they present equal concentrations when applied to standard reactor conditions. Unlike several lumping approaches found in literature, no calculation results from the primary mechanism have been employed prior to the application of our chemical lumping strategy.
Modelling Diesel Spray Ignition Using Detailed Chemistry with a Flamelet Progress Variable Approach
(2006)
Modelling Diesel Spray Ignition Using Detailed Chemistry with a Flamelet Progress Variable Approach
(2005)