TY - JOUR A1 - Fabig, Gunar A1 - Kiewisz, Robert A1 - Lindow, Norbert A1 - Powers, James A. A1 - Cota, Vanessa A1 - Quintanilla, Luis J. A1 - Brugués, Jan A1 - Prohaska, Steffen A1 - Chu, Diana S. A1 - Müller-Reichert, Thomas T1 - Sperm-specific meiotic chromosome segregation in C. elegans JF - eLife Y1 - 2020 U6 - https://doi.org/10.7554/eLife.50988 VL - 9 SP - e50988 ER - TY - JOUR A1 - Lindow, Norbert A1 - Brünig, Florian A1 - Dercksen, Vincent J. A1 - Fabig, Gunar A1 - Kiewisz, Robert A1 - Redemann, Stefanie A1 - Müller-Reichert, Thomas A1 - Prohaska, Steffen A1 - Baum, Daniel T1 - Semi-automatic stitching of filamentous structures in image stacks from serial-section electron tomography JF - bioRxiv N2 - We present a software-assisted workflow for the alignment and matching of filamentous structures across a 3D stack of serial images. This is achieved by combining automatic methods, visual validation, and interactive correction. After an initial alignment, the user can continuously improve the result by interactively correcting landmarks or matches of filaments. Supported by a visual quality assessment of regions that have been already inspected, this allows a trade-off between quality and manual labor. The software tool was developed to investigate cell division by quantitative 3D analysis of microtubules (MTs) in both mitotic and meiotic spindles. For this, each spindle is cut into a series of semi-thick physical sections, of which electron tomograms are acquired. The serial tomograms are then stitched and non-rigidly aligned to allow tracing and connecting of MTs across tomogram boundaries. In practice, automatic stitching alone provides only an incomplete solution, because large physical distortions and a low signal-to-noise ratio often cause experimental difficulties. To derive 3D models of spindles despite the problems related to sample preparation and subsequent data collection, semi-automatic validation and correction is required to remove stitching mistakes. However, due to the large number of MTs in spindles (up to 30k) and their resulting dense spatial arrangement, a naive inspection of each MT is too time consuming. Furthermore, an interactive visualization of the full image stack is hampered by the size of the data (up to 100 GB). Here, we present a specialized, interactive, semi-automatic solution that considers all requirements for large-scale stitching of filamentous structures in serial-section image stacks. The key to our solution is a careful design of the visualization and interaction tools for each processing step to guarantee real-time response, and an optimized workflow that efficiently guides the user through datasets. Y1 - 2020 U6 - https://doi.org/10.1101/2020.05.28.120899 ER - TY - JOUR A1 - Lindow, Norbert A1 - Brünig, Florian A1 - Dercksen, Vincent J. A1 - Fabig, Gunar A1 - Kiewisz, Robert A1 - Redemann, Stefanie A1 - Müller-Reichert, Thomas A1 - Prohaska, Steffen A1 - Baum, Daniel T1 - Semi-automatic stitching of filamentous structures in image stacks from serial-section electron tomography JF - Journal of Microscopy N2 - We present a software-assisted workflow for the alignment and matching of filamentous structures across a three-dimensional (3D) stack of serial images. This is achieved by combining automatic methods, visual validation, and interactive correction. After the computation of an initial automatic matching, the user can continuously improve the result by interactively correcting landmarks or matches of filaments. Supported by a visual quality assessment of regions that have been already inspected, this allows a trade-off between quality and manual labor. The software tool was developed in an interdisciplinary collaboration between computer scientists and cell biologists to investigate cell division by quantitative 3D analysis of microtubules (MTs) in both mitotic and meiotic spindles. For this, each spindle is cut into a series of semi-thick physical sections, of which electron tomograms are acquired. The serial tomograms are then stitched and non-rigidly aligned to allow tracing and connecting of MTs across tomogram boundaries. In practice, automatic stitching alone provides only an incomplete solution, because large physical distortions and a low signal-to-noise ratio often cause experimental difficulties. To derive 3D models of spindles despite dealing with imperfect data related to sample preparation and subsequent data collection, semi-automatic validation and correction is required to remove stitching mistakes. However, due to the large number of MTs in spindles (up to 30k) and their resulting dense spatial arrangement, a naive inspection of each MT is too time-consuming. Furthermore, an interactive visualization of the full image stack is hampered by the size of the data (up to 100 GB). Here, we present a specialized, interactive, semi-automatic solution that considers all requirements for large-scale stitching of filamentous structures in serial-section image stacks. To the best of our knowledge, it is the only currently available tool which is able to process data of the type and size presented here. The key to our solution is a careful design of the visualization and interaction tools for each processing step to guarantee real-time response, and an optimized workflow that efficiently guides the user through datasets. The final solution presented here is the result of an iterative process with tight feedback loops between the involved computer scientists and cell biologists. Y1 - 2021 U6 - https://doi.org/10.1111/jmi.13039 VL - 284 IS - 1 SP - 25 EP - 44 ER -