Refine
Document Type
- Article (12)
- Conference Proceeding (4)
- Part of a Book (1)
- Report (1)
Is part of the Bibliography
- no (18)
Keywords
- Electrodeposition (3)
- water electrolysis (2)
- AEM-Electrolysis (1)
- Anion-exchange membrane water electrolysis (AEMWE) (1)
- Catalysis (1)
- Electrolysis (1)
- Electrolyte pH (1)
- Gas Diffusion Electrode (1)
- High Pressure (1)
- Hydraulic Compression (1)
Institute
Femtosecond laser-induced nano structuring offers a novel approach to enhance the performance of porous transport layers (PTLs) in anion-exchange membrane water electrolysis. By applying ultrashort laser pulses to nickel felts, distinct surface morphologies were generated, including high-spatial-frequency laser-induced periodic surface structures (HSFL-LIPSS), irregular ablated surfaces, and hybrid structures. Surface area analysis revealed increases of up to 4-fold for LIPSS, 6-fold for hybrid structures (LIPSS+Ablation), and 9-fold for ablated surfaces compared to untreated fibers. Electrochemical testing showed reduced overpotentials for laser-treated samples, comparable to state-of-the-art electrodes despite the absence of catalyst layers. Overpotentials could be reduced by up to 6.5 % at 10 mA cm−2 and by up to 9.6 % at 100 mA cm−2 compared to the unprocessed felt. Notably, ablated structures, with the highest surface areas, exhibited microcavities that may entrap oxygen bubbles, limiting active site and reaction rates. The LIPSS structures demonstrated the lowest activation losses and highest current density (1.32 A cm⁻² at 2.0 V) due to their periodic morphology and enhanced electrolyte flow, representing a 17 % improvement at 2.0 V compared to the untreated felts. Moreover, Tafel slopes down to 66 mV dec−1 denote a performant kinetic while oxidation charge measurements revealed pronounced peaks for laser-treated samples, with ablated surfaces achieving the highest charge of 16.76 ± 1.64 C cm⁻². Chronopotentiometry revealed the LIPSS structures showing the highest resistance to degradation among the structured samples.
These findings suggest femtosecond laser nano structuring as a promising method to improve PTL performance. Further application of catalyst layers could amplify the electrochemical efficiency of these advanced materials.
The study introduces flexible and scalable manufacturing approach for electrodes utilizing boron-doped silicon as conductive support for iridium nanoparticles, addressing the challenges of cost and scarcity associated with noble catalysts for oxygen evolution reaction (OER). Colloidal Ir nanoparticles are synthesized via pulsed-laser ablation (≈4–7 nm) and decorated on B-doped Si (≈100 nm) through electrostatic adsorption. Titanium substrates are ultrasonically sprayed with Si:B – Ir and Ir nanoparticles with very low iridium loading of 12 wt.%. Crystalline Ir phases (Ir(111), Ir(200)) are observed and known to enhance the OER mechanism. Additionally, atom probe tomography confirms that the Si support particles contained 0.03-0.5 at.% of boron throughout the entire particle, while electrical permittivity and through-plane measurements reveal a positive impact of B-doped Si on the electrical conductivity of the nanocatalysts and of the ultralow-loaded catalyst coated Ti substrates (0.12 mgIr cm−2), respectively. Rotating disk electrode results show pronounced oxidation peaks for decorated Ir nanoparticles. The Si:B-Ir 4 nm catalyst exhibits the highest turnover frequency (2.62 s−1) and a competitive electrochemical surface area (25 m2 gIr−1) compared to Si:B-Ir 7 nm (0.96 s−1; 37.5 m2 gIr−1) and Ir black (0.24 s−1; 5 m2 gIr−1). The overall analysis of the parameters highlights a performant catalytic efficiency, through balancing activity and reaction kinetics effectively.
Electrodeposited Mo-rich NiMo catalysts offer enhanced catalytic activity for the alkaline hydrogen evolution reaction (HER) and provide an electrically conductive, binder-free substrate connection, making them promising catalysts for green hydrogen production. However, creating Mo-rich deposits is challenging, as the codeposition process typically favors Ni. Optimal deposition conditions for Mo-rich NiMo catalysts remain insufficiently explored. This article investigates Mo-rich NiMo electrodeposition from an ammonia-free citrate bath using NaSO4 as a chlorine-free support electrolyte. The effects of the deposition parameters, 1) sodium molybdate concentration in the electrolyte, 2) deposition current density, and 3) enhanced mass transport via working electrode rotation on the alkaline HER activity, were studied. The electrodeposits, containing 44–66 wt% Mo, exhibited increased surface area due to a rough, cracked morphology and variable oxygen content of the catalyst. The oxygen content was linked to HER activity, revealing an inhibiting effect. The lowest overpotential of 118 mV at −10 mA cm−2 for the alkaline HER was achieved using an electrolyte with 0.02 mol L−1 sodium molybdate, a deposition current density of 600 mA cm−2, without electrode rotation. Respective samples combined a favorable Ni:Mo ratio comprising 56 wt% Mo content with increased surface area and low oxygen content.
The technology of polymer electrolyte membrane (PEM) electrolysis provides an efficient way to produce hydrogen. In combination with renewable energy sources, it promises to be one of the key factors towards a carbon-free energy infrastructure in the future. Today, PEM electrolyzers with a power consumption higher than 1 MW and a gas output pressure of 30 bar (or even higher) are already commercially available. Nevertheless, fundamental research and development for an improved efficiency is far from being finally accomplished, and mostly takes place on a laboratory scale. Upscaling the laboratory prototypes to an industrial size usually cannot be achieved without facing further problems and/or losing efficiency. With our novel system design based on hydraulic cell compression, a lot of the commonly occurring problems like inhomogeneous temperature and current distribution can be avoided. In this study we present first results of an upscaling by a factor of 30 in active cell area.
In this experimental work we present a novel electrolyzer system for the production of hydrogen and oxygen at high pressure levels without an additional mechanical compressor. Due to its control strategies, the operation conditions for this electrolyzer can be kept optimal for each load situation of the system. Furthermore, the novel system design allows for dynamic long-term operation as well as for easy maintainability. Therefore, the device meets the requirements for prospective power-to-gas applications, especially, in order to store excess energy from renewable sources. A laboratory scale device has been developed and high-pressure operation was validated. We also studied the long-term stability of the system by applying dynamic load cycles with load changes every 30 sec. After 80 h of operation the used membrane electrode assembly (MEA) was investigated by means of SEM, EDX and XRD analysis.
In this work, a novel polymer electrolyte membrane water electrolyzer (PEMWE) test cell based on hydraulic single-cell compression is described. In this test cell, the current density distribution is almost homogeneous over the active cell area due to hydraulic cell clamping. As the hydraulic medium entirely surrounds the active cell components, it is also used to control cell temperature resulting in even temperature distribution. The PEMWE single-cell test system based on hydraulic compression offers a 25 cm2 active surface area (5.0 × 5.0 cm) and can be operated up to 80°C and 6.0 A/cm2. Construction details and material selection for the designed test cell are given in this document. Furthermore, findings related to pressure distribution analyzed by utilizing a pressure-sensitive foil, the cell performance indicated by polarization curves, and the reproducibility of results are described. Experimental data indicate the applicability of the presented testing device for relevant PEMWE component testing and material analysis.
For proton exchange membrane water electrolysis (PEMWE) to become competitive, the cost of stack components, such as bipolar plates (BPP), needs to be reduced. This can be achieved by using coated low-cost materials, such as copper as alternative to titanium. Herein we report on highly corrosion-resistant copper BPP coated with niobium. All investigated samples showed excellent corrosion resistance properties, with corrosion currents lower than 0.1 µA cm−2 in a simulated PEM electrolyzer environment at two different pH values. The physico-chemical properties of the Nb coatings are thoroughly characterized by scanning electron microscopy (SEM), electrochemical impedance spectroscopy (EIS), X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM). A 30 µm thick Nb coating fully protects the Cu against corrosion due to the formation of a passive oxide layer on its surface, predominantly composed of Nb2O5. The thickness of the passive oxide layer determined by both EIS and XPS is in the range of 10 nm. The results reported here demonstrate the effectiveness of Nb for protecting Cu against corrosion, opening the possibility to use it for the manufacturing of BPP for PEMWE. The latter was confirmed by its successful implementation in a single cell PEMWE based on hydraulic compression technology.
The present paper presents one- and two-step approaches for electrochemical Pt and Ir deposition on a porous Ti-substrate to obtain a bifunctional oxygen electrode. Surface pre-treatment of the fiber-based Ti-substrate with oxalic acid provides an alternative to plasma treatment for partially stripping TiO2 from the electrode surface and roughening the topography. Electrochemical catalyst deposition performed directly onto the pretreated Ti-substrates bypasses unnecessary preparation and processing of catalyst support structures. A single Pt constant potential deposition (CPD), directly followed by pulsed electrodeposition (PED), created nanosized noble agglomerates. Subsequently, Ir was deposited via PED onto the Pt sub-structure to obtain a successively deposited PtIr catalyst layer. For the co-deposition of PtIr, a binary PtIr-alloy electrolyte was used applying PED. Micrographically, areal micro- and nano-scaled Pt sub-structure were observed, supplemented by homogenously distributed, nanosized Ir agglomerates for the successive PtIr deposition. In contrast, the PtIr co-deposition led to spherical, nanosized PtIr agglomerates. The electrochemical ORR and OER activity showed increased hydrogen desorption peaks for the Pt-deposited substrate, as well as broadening and flattening of the hydrogen desorption peaks for PtIr deposited substrates. The anodic kinetic parameters for the prepared electrodes were found to be higher than those of a polished Ir-disc.
Various aqueous citrate electrolyte compositions for the Ni-Mo electrodeposition are explored in order to deposit Ni-Mo alloys with Mo-content ranging from 40 wt% to 65 wt% to find an alloy composition with superior catalytic activity towards the hydrogen evolution reaction (HER). The depositions were performed on copper substrates mounted onto a rotating disc electrode (RDE) and were investigated via scanning electron microscopy (SEM), X-ray fluorescence (XRF) and X-ray diffraction (XRD) methods as well as linear sweep voltammetry (LSV) and impedance spectroscopy. Kinetic parameters were calculated via Tafel analysis. Partial deposition current densities and current efficiencies were determined by correlating XRF measurements with gravimetric results. The variation of the electrolyte composition and deposition parameters enabled the deposition of alloys with Mo-content over the range of 40-65 wt%. An increase in Mo-content in deposited alloys was recorded with an increase in rotation speed of the RDE. Current efficiency of the deposition was in the magnitude of <1%, which is characteristic for the deposition of alloys with high Mo-content. The calculated kinetic parameters were used to determine the Mo-content with the highest catalytic activity for use in the HER.

