Fachbereich Ingenieur- und Naturwissenschaften
Refine
Document Type
Year of publication
Institute
Has Fulltext
- yes (28)
Is part of the Bibliography
- yes (28) (remove)
Keywords
- 3D measurement (2)
- arc evaporation (2)
- endoscope (2)
- Barium nitrate (1)
- Bragg reflector (1)
- CMOS (1)
- DLC (1)
- Diffraction theory (1)
- Ellipsometry (1)
- Fabry-Perot polymer film sensor (1)
Ellipsometrically obtained spectral dependences of ordinary αxy and extra-ordinary αz extinction/attenuation coefficients within the spectral range λ = 300…980 nm of uniaxially anisotropic polytetrafluoroethylene (PTFE) films were analyzed. We considered the capabilities and specific features of the graphical representation technique for determining the contribution of Rayleigh scattering and Urbach absorption to light attenuation in the spectral range beyond fundamental absorption. It has been shown that the graphical approach enables to estimate these contributions qualitatively, semi-quantitatively or quantitatively, depending on the situation. The conclusions made using the analysis of graphical representation are confirmed by numerical solution of the inverse problem via simulation of the αxy (λ), αz (λ) experimental dependences within the framework of a best-fit procedure. Being based on both of these approaches, we have ascertained that, in the as-prepared PTFE films, the so-called anomalous light scattering (ALS) with the spectral dependence of scattering coefficient αs ≈ as λ–p (p > 4) takes place. Transformation of scattering from ALS to the Rayleigh one with p ≈ 4 due to annealing is accompanied by an increase of Urbach (subband) absorption. Both of these factors cause narrowing the dynamic range of extinction coefficient values. Both scattering and absorption coefficients are higher for the component of light polarized along the normal to the substrate as compared to the component polarized in parallel to it. The relationship between observed behavior of the scattering and absorption coefficients and the film structure has been discussed.
Thin polytetrafluoroethylene (PTFE) films are produced by deposition from a gas phase by two methods: electron-enhanced vacuum deposition (EVD) and EVD + low-temperature plasma (LTP). Structure, morphology, and composition of the films are studied by IR spectroscopy, atomic force microscopy, and X-ray photoelectron spectroscopy. They are close to the structure of bulk PTFE. The roughness of the films’ surface is changed with gas pressure and LTP power variations. Films are transparent from UV to near-infrared regions. Refractive and extinction indices and their anisotropy are measured by spectral ellipsometry. They are tuned by variations of deposition conditions. Hardness and Young modulus of the films are increased if EVD + low power LTP is used for film deposition. Use of EVD + LTP also increases thermal stability of the films. Contact angle of the films corresponds to the bulk PTFE. The PTFE molecules oriented are preferentially in perpendicular direction to the substrate surface.
Through Silicon Via (TSV) technology is a key in 3D integration of circuits by the creation of interconnects using vias, which go through the full silicon wafer. Typically, a highly-selective Bosch Si etch process is used. It is characterized by a high etch rate at a high aspect ratio, whereby scallops on the sidewalls are generated. In this work, square via arrays with dimensions from 3 to 50 μm and up to 300 μm depth were fabricated and analyzed by spectroscopic reflectometry. The reflectometric data are compared to simulations by a novel theoretical approach. In order to simulate the reflectance spectra of TSV arrays, a combination of 2D and 3D rigorous coupled wave analysis was applied. Besides the via depth, the sidewall angle and the corner radius of the bottom profile were considered in the model. The general requirements on spectral resolution in TSV metrology are discussed.
Knowledge of optical constants, i.e. refractive index n and extinction coefficient k, and light scattering properties of optical polymers are required to optimize micro-optics for light-emitting diodes in terms of efficiency, color properties and light distribution. We present here a model-based diagnostic approach to determine the optical properties of polymers, which should be particularly useful in the development of plastics for optical applications. Optical constants and scattering coefficients were obtained from transmission and reflection measurements in a wavelength range from UV to NIR taking into account scattering effects due to rough surfaces and volume inhomogeneity. Based on the models for the dielectric function, the molecular optical transition energies Eg, critical point energies, Urbach energies and exciton transition energies were determined. Rayleigh and Mie scattering model and van de Hulst's anomalous diffraction theory were applied to characterize scattering due to volume inhomogeneities. Scalar diffraction theory was applied to account for surface roughness scattering. Atomic force microscopy with nanomechanical characterization was used to characterize domains in size and shape and to assign optical scattering to a suitable morphological model. The combined optical and mechanical characterization help to improve the qualification of new polymer materials for optical applications.
Electro-optical properties of doped polymers with high transparency in the visible wavelength range
(2021)
The electro-optical (EO) properties of poly(methyl methacrylate) and the photopolymer poly(vinyl cinnamate) doped with varying concentrations of the EO chromophore 2-Methyl-4-nitroaniline were measured. The EO polymers were embedded in Fabry-Pérot etalons for the simultaneous determination of the Pockels and Kerr coefficients from measurements of the fringe shift induced by an external electric field. It was found that the host polymer has a significant impact on the EO performance and that the undoped host polymers exhibit a significant Pockels effect. Moreover, the Kerr effect provides a substantial contribution of 27% to the total change of the refractive index at relatively high electric field strengths of E = 91.2 MV m−1.
This work presents experimental and simulation results of a 3D measurement concept based on fiber-optic interference pattern generation. A demonstrator system which is able to adjust different optical and mechanical parameters is described. The results of parameter variation studies are discussed along with possible applications in the field of micro-optical 3D measurement systems like endoscopes. The experiments were prepared with different structures with various scattering properties. To implement that approach into a micro-optical 3D measurement system, the combination of distance variation between the fibers and a controlled phase shift introduced by a retarder can be used to design the system versatile.
The emission of commercial solid-state lasers is shifted by Raman lasers to selected wavelengths suitable for trace gas detection. High power Raman lasers based on Ba(NO3)2, diamond and silicon detect CO2, O3 and H2O. Raman lasers base on the physical effect of stimulated Raman scattering. Two new Raman crystals (Spodumene and LuAlO3) are investigated and their SRS-spectra is shown.
Tomographic photoacoustic (PA) images acquired using a Fabry-Perot (FP) based scanner offer high resolution and image fidelity but can result in long acquisition times due to the need for raster scanning. To reduce the acquisition times, a parallelised camera-based PA signal detection scheme is developed. The scheme is based on using a sCMOScamera and FPI sensors with high homogeneity of optical thickness. PA signals were acquired using the camera-based setup and the signal to noise ratio (SNR) was measured. A comparison of the SNR of PA signal detected using 1) a photodiode in a conventional raster scanning detection scheme and 2) a sCMOS camera in parallelised detection scheme is made. The results show that the parallelised interrogation scheme has the potential to provide high speed PA imaging.
In this work, a measurement concept based on triangulation was developed for borescopic 3D-surveying of surface defects. The integration of such measurement system into a borescope environment requires excellent space utilization. The triangulation angle, the projected pattern, the numerical apertures of the optical system, and the viewing angle were calculated using partial coherence imaging and geometric optical raytracing methods. Additionally, optical aberrations and defocus were considered by the integration of Zernike polynomial coefficients. The measurement system is able to measure objects with a size of 50 μm in all dimensions with an accuracy of ± 5 μm. To manage the issue of a low depth of field while using an optical high resolution system, a wavelength dependent aperture was integrated. Thereby, we are able to control depth of field and resolution of the optical system and can use the borescope in measurement mode with high resolution and low depth of field or in inspection mode with low resolution and higher depth of field. First measurements of a demonstrator system are in good agreement with our simulations.
In this study, we present the experimental investigations on interference patterns, such as those already reported in VIMOS-IFU, and up to now no appropriate explanation has been presented. These interference patterns are produced in multimode fibres coated with acrylate or polyimide, which is the preferred coating material for the fibres used in IFUs. Our experiments show that, under specific conditions, cladding modes interact with the coating and produce interference. Our results show that the conditions at which the fibre is held during data acquisition has an impact in the output spectrum. Altering the positioning conditions of the fibre leads to the changes into the interference pattern, therefore, fibres should be carefully manipulated in order to minimise this potential problem and improve the performance of these instruments. Finally we present a simple way of predicting and modelling this interference produced from the visible to the near infrared spectra. This model can be included in the data reduction pipeline in order to remove the interference patterns.
These results should be of interest for the optimisation of the data reduction pipelines of instruments using optical fibres. Considering these results will benefit innovations and developments of high performance fibre systems.