TY - JOUR A1 - Villringer, Claus A1 - Steglich, Patrick A1 - Pulwer, Silvio A1 - Schrader, Sigurd A1 - Laufer, Jan T1 - Electro-optical properties of doped polymers with high transparency in the visible wavelength range JF - Optical Materials Express N2 - The electro-optical (EO) properties of poly(methyl methacrylate) and the photopolymer poly(vinyl cinnamate) doped with varying concentrations of the EO chromophore 2-Methyl-4-nitroaniline were measured. The EO polymers were embedded in Fabry-Pérot etalons for the simultaneous determination of the Pockels and Kerr coefficients from measurements of the fringe shift induced by an external electric field. It was found that the host polymer has a significant impact on the EO performance and that the undoped host polymers exhibit a significant Pockels effect. Moreover, the Kerr effect provides a substantial contribution of 27% to the total change of the refractive index at relatively high electric field strengths of E = 91.2 MV m−1. KW - Bragg reflector KW - fiber optic coupler KW - refractive index KW - spatial light modulator KW - transparency KW - tunable filter Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:526-opus4-15480 VL - 11 IS - 11 SP - 3801 EP - 3811 PB - Optica Publishing Group ER - TY - CHAP A1 - Steglich, Patrick A1 - Mai, Christian A1 - Stolarek, David A1 - Lischke, Stefan A1 - Kupijai, Sebastian A1 - Villringer, Claus A1 - Pulwer, Silvio A1 - Heinrich, Friedhelm A1 - Bauer, Joachim A1 - Meister, Stefan A1 - Knoll, Dieter A1 - Casalboni, Mauro A1 - Schrader, Sigurd T1 - Partially slotted silicon ring resonator covered with electro-optical polymer T2 - Proceedings of SPIE N2 - In this work, we present for the first time a partially slotted silicon ring resonator (PSRR) covered with an electro-optical polymer (Poly[(methyl methacrylate)-co-(Disperse Red 1 acrylate)]). The PSRR takes advantage of both a highly efficient vertical slot waveguide based phase shifter and a low loss strip waveguide in a single ring. The device is realized on 200 mm silicon-on-insulator wafers using 248 nm DUV lithography and covered with the electro-optic polymer in a post process. This silicon-organic hybrid ring resonator has a small footprint, high optical quality factor, and high DC device tunability. A quality factor of up to 105 and a DC device tunability of about 700 pm/V is experimentally demonstrated in the wavelength range of 1540 nm to 1590 nm. Further, we compare our results with state-of-the-art silicon-organic hybrid devices by determining the poling efficiency. It is demonstrated that the active PSRR is a promising candidate for efficient optical switches and tunable filters. Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:526-opus4-13771 SN - 1996-756X ER - TY - CHAP A1 - Padilla-Michel, Yazmin A1 - Pulwer, Silvio A1 - Saffari, Pouneh A1 - Ksianzou, Viachaslau A1 - Schrader, Sigurd T1 - On the origin and removal of interference patterns in coated multimode fibres N2 - In this study, we present the experimental investigations on interference patterns, such as those already reported in VIMOS-IFU, and up to now no appropriate explanation has been presented. These interference patterns are produced in multimode fibres coated with acrylate or polyimide, which is the preferred coating material for the fibres used in IFUs. Our experiments show that, under specific conditions, cladding modes interact with the coating and produce interference. Our results show that the conditions at which the fibre is held during data acquisition has an impact in the output spectrum. Altering the positioning conditions of the fibre leads to the changes into the interference pattern, therefore, fibres should be carefully manipulated in order to minimise this potential problem and improve the performance of these instruments. Finally we present a simple way of predicting and modelling this interference produced from the visible to the near infrared spectra. This model can be included in the data reduction pipeline in order to remove the interference patterns. These results should be of interest for the optimisation of the data reduction pipelines of instruments using optical fibres. Considering these results will benefit innovations and developments of high performance fibre systems. KW - instrumentation KW - multimode fibre KW - bending loss KW - fringing KW - interference KW - coating material KW - data reduction Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:526-opus4-15295 SP - 1517 EP - 1527 PB - Society of Photo-Optical Instrumentation Engineers (SPIE) ER - TY - CHAP A1 - Pulwer, Silvio A1 - Steglich, Patrick A1 - Villringer, Claus A1 - Bauer, Joachim A1 - Burger, Martin A1 - Franz, M. A1 - Grieshober, K. A1 - Wirth, F. A1 - Blondeau, J. A1 - Rautenberg, J. A1 - Mouti, S. A1 - Schrader, Sigurd T1 - Triangulation-based 3D surveying borescope N2 - In this work, a measurement concept based on triangulation was developed for borescopic 3D-surveying of surface defects. The integration of such measurement system into a borescope environment requires excellent space utilization. The triangulation angle, the projected pattern, the numerical apertures of the optical system, and the viewing angle were calculated using partial coherence imaging and geometric optical raytracing methods. Additionally, optical aberrations and defocus were considered by the integration of Zernike polynomial coefficients. The measurement system is able to measure objects with a size of 50 μm in all dimensions with an accuracy of ± 5 μm. To manage the issue of a low depth of field while using an optical high resolution system, a wavelength dependent aperture was integrated. Thereby, we are able to control depth of field and resolution of the optical system and can use the borescope in measurement mode with high resolution and low depth of field or in inspection mode with low resolution and higher depth of field. First measurements of a demonstrator system are in good agreement with our simulations. KW - borescope KW - 3D measurement KW - triangulation KW - lens design KW - calibration KW - defect Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:526-opus4-15307 SP - 51 EP - 56 PB - SPIE ER - TY - CHAP A1 - Pulwer, Silvio A1 - Jahns, Daniel A1 - Villringer, Claus A1 - Schrader, Sigurd T1 - Dynamic pattern generation by singlemode fibers for endoscopic 3D measurement systems N2 - This work presents experimental and simulation results of a 3D measurement concept based on fiber-optic interference pattern generation. A demonstrator system which is able to adjust different optical and mechanical parameters is described. The results of parameter variation studies are discussed along with possible applications in the field of micro-optical 3D measurement systems like endoscopes. The experiments were prepared with different structures with various scattering properties. To implement that approach into a micro-optical 3D measurement system, the combination of distance variation between the fibers and a controlled phase shift introduced by a retarder can be used to design the system versatile. KW - endoscope KW - 3D measurement KW - phase shift KW - fiber Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:526-opus4-15364 PB - SPIE ER - TY - CHAP A1 - Villringer, Claus A1 - Gilani, Taravat Saeb A1 - Zhang, Edward A1 - Pulwer, Silvio A1 - Steglich, Patrick A1 - Schrader, Sigurd A1 - Laufer, Jan T1 - Development of tuneable Fabry-Pérot sensors for parallelised photoacoustic signal acquisition T2 - Proc. SPIE 10878, Photons Plus Ultrasound: Imaging and Sensing 2019, 108780M (8 March 2019) N2 - Fabry-Pérot (FP) sensors have enabled high resolution 3D photoacoustic (PA) imaging in backward mode. However, raster-scanning of the interrogation laser beam across the sensor can result in slow 3D image acquisition. To overcome this limitation, parallelized PA signal acquisition can be used for which FP sensors with uniform optical thickness are required. In this work, the optical thickness is tuned a) irreversibly through the use of a photopolymer host matrix and b) actively using embedded electro-optic (EO) chromophores. Polymer spacers (5 μm) were deposited using spin coating and sandwiched between two dielectric mirrors and transparent ITO electrodes. The employed polymer guest-host system consists of an EO chromophore (2-methyl-4-nitroaniline) and poly(vinyl cinnamate). EO tuneability was induced using contact poling and a tuneability of 68 pm was demonstrated. The optical thickness was homogenised by raster scanning a UV beam whilst varying the exposure time across a 4 mm2 detection aperture. Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:526-opus4-13769 SN - 1996-756X PB - Society of Photo-Optical Instrumentation Engineers (SPIE) ER - TY - CHAP A1 - Bauer, Joachim A1 - Heinrich, Friedhelm A1 - Fursenko, Oksana A1 - Marschmeyer, Steffen A1 - Bluemich, Adrian A1 - Pulwer, Silvio A1 - Steglich, Patrick A1 - Villringer, Claus A1 - Mai, Andreas A1 - Schrader, Sigurd T1 - Very high aspect ratio through silicon via reflectometry T2 - Proceedings of SPIE N2 - Through Silicon Via (TSV) technology is a key feature of new 3D integration of circuits by creation of interconnections using vias, which go through the silicon wafer. Typically, the highly-selective Bosch Si etch process, characterized by a high etch rate and high aspect ratio and forming of scallops on the sidewalls is used. As presented in this paper, we have developed an experimental setup and a respective evaluation algorithm for the control and monitoring of very high aspect ratio TSV profiles by spectroscopic reflectometry. For this purpose square via arrays with lateral dimension from 3 to 10 μm were fabricated by a Bosch etch process and analyzed by our setup. By exploiting interference and diffraction effects of waves reflected from the top and bottom surfaces as well as from the side walls of the TSV patterns, the measurements provided etch depths, CD values and scallop periods. The results were compared with data obtained by a commercial wafer metrology tool. Aspect ratios of up to 35:1 were safely evaluable by our setup. Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:526-opus4-13758 SN - 1996-756X ER - TY - GEN A1 - Steglich, Patrick A1 - Villringer, Claus A1 - Pulwer, Silvio A1 - Bauer, Joachim A1 - Heinrich, Friedhelm A1 - Casalboni, Mauro A1 - Schrader, Sigurd T1 - Advanced Nanophotonics: Silicon-Organic Hybrid Technology T2 - Wissenschaftliche Beiträge 2016 N2 - Integrated photonic devices have gained increasing research interests. Especially silicon photonics have become very attractive for various optical applications. Using silicon-on-insulator as a material platform provides the ability to fabricate photonic devices with electronic devices on a single chip. Driven by substantial research investments, the integration of photonic devices on silicon-on-insulator substrates has reached a degree of maturity that already permits industrial adoption. However, silicon has the disadvantage of linear electro-optical effects, and, therefore, advanced modulation formats are difficult to realize when using silicon-based high-speed modulators. Hence, a new approach was proposed: the silicon-organic hybrid technology. This technology is a viable extension of the silicon-on-insulator material system for efficient high-speed modulation. We herewith present our theoretical and experimental investigations of the silicon-organic hybrid slot-waveguide ring resonator. The advanced device design is described in detail, which allows using both, the efficient silicon-on-insulator strip-waveguides and the silicon-organic hybrid slot-waveguides in single ring resonator. For the first time, we report the transmission spectra of such a resonator covered with an electro-optical polymer. N2 - Integrierte photonische Bauelemente werden in der Forschung immer bedeutender. Besonders die Siliziumphotonik ist für verschiedene optische Anwendungen sehr attraktiv. Die Verwendung von Silizium-auf-Isolator-Materialsystemen bietet die Möglichkeit, photonische Bauelemente mit elektronischen Geräten auf einem einzelnen Chip zu entwickeln. Durch erhebliche Forschungsinvestitionen hat die photonische Integration auf Silizium-auf-Isolator-Substraten einen Reifegrad, der bereits Industriemaßstäben genügt. Jedoch hat Silizium keinen linearen elektrooptischen Effekt und damit sind moderne Modulationsformate nur schwierig zu realisieren. Daher wird seit eingen Jahren ein neuer Ansatz, die Silizium-Organik Hybridtechnologie, verfolgt. Diese Technologie ist eine tragfähige Ausdehnung des Silizium-auf-Isolator-Materialsystems für eine effiziente Hochgeschwindigkeitsmodulation und optische Signalverarbeitung. In diesem Artikel präsentieren wir unsere theoretischen und experimentellen Untersuchungen zu einem Silizium-Organik Hybrid Ringresonator. Das Design und die Herstellung des neuartigen nanophotonischen Bauelements werden im Detail beschrieben. Der demonstrierte Ringresonator kombiniert die Vorteile zweier verschiedener Wellenleiterarten in einem einzelnen Ring, dem verlustarmen Kanal-Wellenleiter und dem Silizium-organischen Hybridschlitzwellenleiter. Wir demonstrieren erstmals ein Transmissionsspektrum eines solchen Ringresonators, der mit einem elektro-optischen Polymer beschichtet ist. Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:526-opus4-5337 SN - 0949-8214 VL - 20 SP - 45 EP - 48 ER - TY - JOUR A1 - Baumann, Elisabeth A1 - Pohle, Ulrike A1 - Zhang, Edward A1 - Allen, Thomas A1 - Villringer, Claus A1 - Pulwer, Silvio A1 - Gerhardt, Holger A1 - Laufer, Jan T1 - A backward-mode optical-resolution photoacoustic microscope for 3D imaging using a planar Fabry-Pérot sensor JF - Photoacoustics N2 - Optical-resolution photoacoustic microscopy (OR-PAM) combines high spatial resolution and strong absorption-based contrast in tissue, which has enabled structural and spectroscopic imaging of endogenous chromophores, primarily hemoglobin. Conventional piezoelectric ultrasound transducers are typically placed far away from the photoacoustic source due to their opacity, which reduces acoustic sensitivity. Optical ultrasound sensors are an alternative as their transparency allows them to be positioned close to the sample with minimal source-detector distances. In this work, a backward-mode OR-PAM system based on a planar Fabry-Pérot ultrasound sensor and coaxially aligned excitation and interrogation beams was developed. Two 3D imaging modes, using raster-scanning for enhanced image quality and continuous-scanning for fast imaging, were implemented and tested on a leaf skeleton phantom. In fast imaging mode, a scan-rate of 100,000 A-lines/s was achieved. 3D images of a zebrafish embryo were acquired in vivo in raster-scanning mode. The transparency of the FP sensor in the visible and near-infrared wavelength region makes it suitable for combined functional and molecular imaging applications using OR-PAM and multi-photon fluorescence microscopy. KW - optical-resolution photoacoustic microscopy KW - backward-mode imaging KW - dual-wavelength KW - continuous scanning KW - in vivo imaging KW - optical ultrasound sensing KW - planar Fabry-Pérot interferometer Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:526-opus4-14701 SN - 2213-5979 VL - 24 SP - 100293 PB - Elsevier ER - TY - CHAP A1 - Pohle, Ulrike A1 - Baumann, Elisabeth A1 - Pulwer, Silvio A1 - Villringer, Claus A1 - Zhang, Edward A1 - Gerhardt, Holger A1 - Laufer, Jan T1 - Development of a backward-mode photoacoustic microscope using a Fabry-Pérot sensor N2 - Optical-resolution photoacoustic microscopy (PAM) has been shown to enable the acquisition of high resolution (μm) functional and anatomical images. For backward-mode operation, conventional piezoelectric ultrasound transducers need to be placed far away from the signal source due to their opacity and size. This can result in reduced acoustic sensitivity. Planar Fabry-Perot polymer film interferometer (FPI) sensors have the potential to overcome this limitation since they are transparent to the excitation wavelength, can be placed immediately adjacent to the signal source for high acoustic sensitivity, and offer a broadband frequency response (0 –50 MHz). In this study, we present a high frame rate, backward-mode OR-PAM system based on a planar FPI ultrasound sensor. A ns-pulsed laser provides excitation pulses (<200 nJ, maximum pulse repetition frequency = 200 kHz, 532 nm) to generate photoacoustic waves that are detected using a planar FPI sensor interrogated at 765-781 nm. For backwardmode operation and highest acoustic sensitivity, the excitation and interrogation beams are coaxially aligned and rasterscanned. The optical transfer function of the sensor, the spatial resolution and the detection sensitivity were determined to characterise the set-up. Images of a leaf phantom and first in vivo images of zebrafish larvae were acquired. This approach will enable fast 3D OR-PAM with high resolution and high sensitivity for functional and molecular imaging applications. FPI-based ultrasound detection also has the potential to enable dual-mode optical- and acousticresolution PAM and the integration of photoacoustic imaging with purely optical modalities such as multi-photon microscopy. KW - optical-resolution photoacoustic microscopy KW - Fabry-Perot ultrasound sensor KW - in vivo imaging Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:526-opus4-15349 SP - 594 EP - 598 PB - SPIE ER - TY - CHAP A1 - Pulwer, Silvio A1 - Fiebelkorn, Richard A1 - Zesch, Christoph A1 - Steglich, Patrick A1 - Villringer, Claus A1 - Villasmunta, Francesco A1 - Gedat, Egbert A1 - Handrich, Jan A1 - Schrader, Sigurd A1 - Vandenhouten, Ralf T1 - Endoscopic orientation by multimodal data fusion T2 - Proc. SPIE 10931, MOEMS and Miniaturized Systems XVIII N2 - To improve the feasibility of endoscopic inspection processes we developed a system that provides online information about position, orientation and viewing direction of endoscopes, to support the analysis of endoscopic images and to ease the operational handling of the equipment. The setup is based on an industrial endoscope consisting of a camera, various MEMS and multimodal data fusion. The software contains algorithms for feature and geometric structure recognition as well as Kalman filters. To track the distal end of the endoscope and to generate 3D point cloud data in real time the optical and photometrical characteristics of the system are registered and the movement of the endoscope is reconstructed by using image processing techniques. KW - endoscope KW - orientation KW - Kalman filter KW - visual odometry KW - mems KW - gyroscope KW - accelerometer Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:526-opus4-11420 SN - 1996-756X ER - TY - JOUR A1 - Steglich, Patrick A1 - Mai, Christian A1 - Villringer, Claus A1 - Dietzel, Birgit A1 - Bondarenko, Siegfried A1 - Ksianzou, Viachaslau A1 - Villasmunta, Francesco A1 - Zesch, Christoph A1 - Pulwer, Silvio A1 - Burger, Martin A1 - Bauer, Joachim A1 - Heinrich, Friedhelm A1 - Schrader, Sigurd A1 - Vitale, Francesco A1 - De Matteis, Fabio A1 - Prosposito, Paolo A1 - Casalboni, Mauro A1 - Mai, Andreas T1 - Silicon-organic hybrid photonics: an overview of recent advances, electro-optical effects and CMOS integration concepts JF - Journal of Physics: Photonics N2 - In recent decades, much research effort has been invested in the development of photonic integrated circuits, and silicon-on-insulator technology has been established as a reliable platform for highly scalable silicon-based electro-optical modulators. However, the performance of such devices is restricted by the inherent material properties of silicon. An approach to overcoming these deficiencies is to integrate organic materials with exceptionally high optical nonlinearities into a silicon-on-insulator photonic platform. Silicon–organic hybrid photonics has been shown to overcome the drawbacks of silicon-based modulators in terms of operating speed, bandwidth, and energy consumption. This work reviews recent advances in silicon–organic hybrid photonics and covers the latest improvements to single components and device concepts. Special emphasis is given to the in-device performance of novel electro-optical polymers and the use of different electro-optical effects, such as the linear and quadratic electro-optical effect, as well as the electric-field-induced linear electro-optical effect. Finally, the inherent challenges of implementing non-linear optical polymers on a silicon photonic platform are discussed and a perspective for future directions is given. Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:526-opus4-13882 SN - 2515-7647 VL - 3 IS - 2 ER - TY - GEN A1 - Steglich, Patrick A1 - Villringer, Claus A1 - Pulwer, Silvio A1 - Dietzel, Birgit A1 - Ksianzou, Viachaslau A1 - Schrader, Sigurd T1 - Chip-integrierte photonische Bauelemente T2 - Wissenschaftliche Beiträge 2017 N2 - In unserer hochtechnologisierten Gesellschaft spielt die optische Datenübertragung aufgrund der stetig wachsenden Informationsvielfalt eine immer bedeutendere Rolle. In den Anfängen der Nachrichtentechnik waren Datenraten von wenigen bit/s realisierbar. Heute werden mittels optischer Technologien Übertragungsraten von mehreren Gbit/s umgesetzt. Möglich wird dies durch neue Entwicklungen in der Chip-integrierten Photonik. Beispiele dafür sind Chip-integrierte elektrooptische Modulatoren und Schalter. In diesem Artikel werden neue Entwicklungen in der Chip-integrierten Photonik diskutiert und die experimentelle Charakterisierung der Bauelemente in Form eines Ringresonators beschrieben. Für die Experimente wird exemplarisch ein photonisches Bauelement genutzt, das aus einem hybriden Silizium-Polymer-Materialsystem besteht. Die Ergebnisse zeigen, dass diese Materialkombination vielversprechend für zukünftige Chip-integrierte photonische Bauelemente mit extrem geringem Energiebedarf ist. N2 - The focus on high-tech in our society makes optical data transmission increasingly important due to the continually growing diversity of information. At the very beginning of integrated photonics, the data rates achieved were only a few bit/s. Today, transfer rates of several Gbit/s are possible due to novel chip-integrated devices such as electro-optical modulators and switches. This trend was made possible due to new developments in the field of Chip-integrated photonics. In this article, we discuss latest developments in the field of chip-integrated photonic devices and describe their experimental characterization. The experimental setup is developed and described in detail. The example used in our experiments is a hybrid silicon-polymer material system. Our results show that the hybrid material approach is a promising candidate for future on-chip integrated photonic devices with low power consumption. Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:526-opus4-9426 SN - 0949-8214 VL - 21 SP - 55 EP - 59 ER - TY - GEN A1 - Steglich, Patrick A1 - Ksianzou, Viachaslau A1 - Villringer, Claus A1 - Pulwer, Silvio A1 - Schrader, Sigurd T1 - Theorie der Modenlinienspektroskopie zur optischen Charakterisierung von Polymerschichten T2 - Wissenschaftliche Beiträge 2018 N2 - Die Modenlinienspektroskopie kann zur hochpräzisen Charakterisierung von Polymerschichten bezüglich des Brechungsindex verwendet werden. Das vorliegende Manuskript behandelt die Theorie der Modenlinienspektroskopie und beginnt dabei mit den theoretischen Grundlagen eines planaren Wellenleiters, die zum Verständnis der Modenlinienspektroskopie notwendig sind. Die hier präsentierten expliziten Herleitungen können genutzt werden, um die Modenlinienspektroskopie so zu modifizieren, dass auch die Messung des Pockelseffektes möglich ist. Eine Anwendungsmöglichkeit soll in der zukünftigen Bestimmung des Pockelskoeffizienten bestehen, der für die Weiterentwicklung von polymerbasierten elektrooptischen Modulatoren benötigt wird. Zudem werden der Aufbau und die experimentelle Herangehensweisen beschrieben und die Brechungsindexbestimmung wird exemplarisch am Beispiel einer Wirt-Gast-Polymerschicht demonstriert. N2 - M-Line spectroscopy can be used for high precision measurements of polymer layers. The present manuscript deals with the theory of m-line spectroscopy and thus begins with the theoretical background of a planar waveguide structure, which is necessary for a deeper understanding of m-line spectroscopy. The explicit derivations presented here can be used to modify the m-line spectroscopy in such a way that the measurement of the Pockels effect is also possible. One application is to be obtained in the future configuration of the Pockels coefficients, which is needed to optimize electro-optical modulators. In addition, the set-up and the experimental approach are described. Finally, a host-guest polymer layer is experimentally characterized in terms of the refractive index. Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:526-opus4-10248 SN - 0949-8214 VL - 22 SP - 31 EP - 38 ER - TY - JOUR A1 - Steglich, Patrick A1 - Mai, Christian A1 - Villringer, Claus A1 - Pulwer, Silvio A1 - Casalboni, Mauro A1 - Schrader, Sigurd A1 - Mai, Andreas T1 - Quadratic electro-optic effect in silicon-organic hybrid slot-waveguides JF - Optics Letters N2 - This Letter reports on the quadratic electro-optic effect of polymers, observed in a silicon slot-waveguide at low voltages. We demonstrate that in narrow slots, the electro-optic response with respect to refractive index change is strong enough for on-chip wavelength tuning and intensity modulation using voltages as low as 1 V. A silicon slot-waveguide embedded by a nonlinear optical polymer, consisting of the dye Disperse Red 1 in poly(methyl methacrylate), serves as the phase shifter in a racetrack ring resonator. As deduced from the experimental data, the third-order susceptibility of the utilized electro-optic polymer is about 2·10−19 m2/V2. The demonstrated low-voltage operation and inherently thermal stability show the potential for silicon-organic hybrid devices using the quadratic electro-optic effect. Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:526-opus4-12148 SN - 1539-4794 VL - 43 IS - 15 ER -